Sharif Digital Repository

In this article, out-of-phase thermo-mechanical fatigue (TMF) behaviours of light alloys were investigated in comparison to their high temperature low cycle fatigue (LCF) behaviours. For this objective, strain based fatigue tests were performed on the A356 aluminium alloy and on the AZ91 magnesium alloy. Besides, TMF tests were carried out, where both strain and temperature changed. The fatigue lifetime comparison demonstrated that the TMF lifetime was less than that one under LCF loadings at elevated temperatures for both light alloys. The reason was due to severe conditions in TMF tests in comparison to LCF tests. The temperature varied in TMF test but it was constant under LCF loadings.... 

In this paper, a new fatigue lifetime prediction model is presented for the aluminium-silicon-magnesium alloy, A356.0. This model is based on the plastic strain energy density per cycle including two correction factors in order to consider the effect of the mean stress and the maximum temperature. The thermal term considers creep and oxidation damages in A356.0 alloy. To calibrate the model, isothermal fatigue and out-of-phase thermo-mechanical fatigue (TMF) tests were conducted on the A356.0 alloy. Results showed an improvement in predicting fatigue lifetimes by the present model in comparison with classical theories and also the plastic strain energy density (without any correction... 

In the present paper, the heat treatment effect on A356.0, a cast aluminum alloy which has been widely used in diesel engine cylinder heads, is investigated under out-of-phase thermo-mechanical fatigue and low cycle fatigue (at different temperatures) loadings. A typical heat treatment is applied to the material including 8. h solution at 535 °C, water quench and 3. h ageing at 180 °C. The experimental fatigue results show that the heat treatment process has considerable influence on mechanical and low cycle fatigue behaviors, especially at room temperature, but its effect on thermo-mechanical fatigue lifetime is not significant. The improvement in the strength can be explained by the... 

In this investigation, the effect of microstructural constituents on thermal fatigue resistance of A319 aluminum casting alloy was studied. For this purpose, both thermo-mechanical fatigue and thermal-shock fatigue experiments were performed in thermal cycling range between 40 and 250 °C. Following the results, samples with finer SDAS, lower porosity volume fraction and lower brittle intermetallic contents, as well as higher Si modification showed better thermal fatigue resistance. Moreover, T6 and T7 heat treatments appeared to be highly beneficial for thermal fatigue performance. According to the fractography analysis, porosities and coarse intermetallic phases were determined as the most... 

In the present paper, thermo-mechanical fatigue (TMF) and low cycle fatigue (LCF) or isothermal fatigue (IF) lifetimes of a cast magnesium alloy (the AZ91 alloy) were studied. In addition to a heat treatment process (T6), several rare elements were added to the alloy to improve the material strength in the first step. Then, the cyclic behavior of the AZ91 was investigated. For this objective, strain-controlled tension-compression fatigue tests were carried out. The temperature varied between 50 and 200. °C in the out-of-phase (OP) TMF tests. The constraint factor which was defined as the ratio of the mechanical strain to the thermal strain, was set to 75%, 100% and 125%. For LCF tests,... 

In this article, numerical simulations of cyclic behaviors in light alloys are conducted under isothermal and thermo-mechanical fatigue loadings. For this purpose, an aluminum alloy (A356) which is widely used in cylinder heads and a magnesium alloy (AZ91) which can be applicable in cylinder heads are considered to study their stress-strain hysteresis loops. Two plasticity approaches including the Chaboche's hardening model and the Nagode's spring-slider model are applied to simulate cyclic behaviors. To validate obtained results, strain-controlled fatigue tests are performed under low cycle and thermo-mechanical fatigue loadings. Numerical results demonstrate a good agreement with... 

In the present paper, an improvement in high temperature fatigue properties of the AZ91 magnesium alloy with rare earth elements has been obtained by a typical heat treatment, denoted by T6. For this objective, out-of-phase thermo-mechanical fatigue, room temperature and high temperature low cycle fatigue tests are performed to compare lifetimes. Several rare earth elements are initially added to the AZ91 alloy during a gravity casting process in permanent molds. Also, the type of the heat treatment is examined. Results of specimens with only the solution (the T4 heat treatment) and the solution with the ageing process (the T6 heat treatment) are compared under isothermal fatigue loadings.... 

This paper presents the fatigue lifetime of an aluminum-silicon-magnesium alloy, widely used in diesel engine cylinder heads, both with and without a thermal barrier coating (TBC) system. The coating system in this study consists of two layers including a 150 μm thick metallic bond coat and a zirconium oxide top coat 350 μm thick. These coating layers were applied on the substrate of A356.0 alloy by air plasma thermal spraying. The isothermal fatigue tests were conducted in low cycle fatigue (LCF) regime at various temperatures. Out-of-phase thermo-mechanical fatigue (OP-TMF) tests were also performed at different maximum temperatures and constraint factors. Experimental results demonstrate... 

In this paper, effects of strain rate and mean strain on the cyclic behavior and the lifetime of aluminum-silicon alloys are investigated under thermo-mechanical and isothermal fatigue loadings. To achieve these goals, low cycle fatigue tests are accomplished at evaluated temperatures under various strain rates (by changing the loading frequency) and different strain ratios (minimum to maximum strain). Thermo-mechanical fatigue experiments are performed in an out-of-phase condition where the temperature varies between 50 and 250 °C. Various heating/cooling rates are taken into account to assess the strain rate effect and different starting temperatures are considered to study the mean strain... 

In this article, a novel energy-based lifetime prediction model has been presented for uncoated and coated aluminum alloys, subjected to thermal and mechanical fatigue loadings. For this objective, isothermal and thermo-mechanical fatigue tests were performed on the A356.0 alloy, with and without thermal barrier coating systems. This model, which was based on the plastic strain energy, had three correction factors including temperature, strain and mean stress effects. The predicted lifetime showed a proper agreement with experimental data. By the present model, higher accuracy was obtained in comparison to other existed approaches. Besides, the present model had lower number of material... 

In this article, simulations of the stress-strain behavior in aluminum alloys were investigated under cyclic loadings at various strain rates. Four plasticity approaches were applied to simulate cyclic behaviors. To validate obtained results, strain-controlled tensile-compressive fatigue tests were performed in the low cycle fatigue regime. Isothermal fatigue experiments were conducted at various strain rates. Thermo-mechanical fatigue experiments were carried out at different rates of cooling and heating processes. Numerical results demonstrated a good agreement with experimental data at the mid-life cycle of the material. Material constants for different models were also presented for... 

Cast aluminium-silicon alloy, A356.0, is widely used in automotive and aerospace industries because of its outstanding mechanical, physical, and casting properties. Thermal barrier coatings can be applied to combustion chamber to reduce fuel consumption and pollutions and also improve fatigue life of components. The purpose of the present work is to simulate stress distribution of A356.0 under thermo-mechanical cyclic loadings, using a two-layer elastic-visco-plastic model of ABAQUS. The results of stress-strain hysteresis loop are validated by an out of phase thermo-mechanical fatigue test. Different thicknesses from 300 to 800. μm of top coat and also roughness of the interfaces are... 

This article presents the cyclic behavior of the A356.0 aluminum alloy under low-cycle fatigue (or isothermal) and thermo-mechanical fatigue loadings. Since the thermo-mechanical fatigue (TMF) test is time consuming and has high costs in comparison to low-cycle fatigue (LCF) tests, the purpose of this research is to use LCF test results to predict the TMF behavior of the material. A time-independent model, considering the combined nonlinear isotropic/kinematic hardening law, was used to predict the TMF behavior of the material. Material constants of this model were calibrated based on room-temperature and high-temperature low-cycle fatigue tests. The nonlinear isotropic/kinematic hardening... 

In the present study, the out-of-phase thermomechanical fatigue (OP-TMF) behavior of a cast aluminum-silicon-magnesium alloy, the A356.0 alloy which has been widely used in diesel engine cylinder heads, is compared to room-temperature and high-temperature low cycle fatigue (RT-, HT-LCF) behaviors. For this purpose, strain/temperature-controlled isothermal and non-isothermal fatigue tests were performed based on realistic loading conditions in cylinder heads. Fatigue tests results showed that the plastic strain increased during cycles under constant mechanical strain amplitude, while the specimen failed. Under LCF loadings, the cyclic hardening occurred at low temperatures for the A356.0... 

Radial forging is one of the modern open die forging techniques and has a wide application in producing machine parts. During operation at high temperatures, severe temperature change associated with mechanical loads and the resultant wearing of the die surface lead to intense variation in strain on the die surface. Therefore, under this operating condition, thermo-mechanical fatigue (TMF) occurs on the surface of the radial forging die. TMF decreases the life of the die severely. In the present research, different layers were deposited on a 1.2714 steel die by SMAW and GTAW, with a weld wire of UDIMET 520. The microstructure of the radial forging die surface was investigated during welding...