Sharif Digital Repository

Improvement in switching techniques is one of the effective methods for increasing the voltage quality in Multilevel Inverters. In this paper, a novel switching technique using frequency modulation is proposed to achieve high quality output voltage of multilevel inverters. This method is employed to different configurations of multilevel inverters consist of Diode Clamped (or Neutral Point Clamped), Flying Capacitor and Cascaded H-bridge. Each multilevel inverter which utilizes this technique is modeled and simulated to investigate the performance of this method by the help of MATLAB/Simulink software. The Results show that this innovative method considerably reduces total harmonic... 

Harmonic information is necessary tools in the estimation of motors life and performance. The conventional expression of harmonic amount is carried out by total Harmonic distortion. This distortion factor is only related to amplitude of harmonics while the motor loss is affected by frequency domain of them. In this paper a new definition of this factor has been presented. This definition includes the frequency of harmonics as well as their amplitudes. Experimental results verify the validity of this new definition  

In this paper the aim is to minimize the total harmonic distortion (THD) in PWM inverters while suppressing chosen harmonics concurrently and maintaining the fundamental component of the output voltage at a required level. This is reformed as an optimization task and the optimal pulse patterns are accomplished using genetic algorithm (GA) optimization technique to minimize a predefined fitness function. The complete solutions that suppress the 5 th and 7 th harmonics and optimize the THD are given. A practical limitation on the determination of sequential switching angles has been considered as a set of constraints in derivation of the results. © 2006 IEEE  

This paper presents a single-phase Cascaded H-Bridge (CHB) inverter for photovoltaic applications. The proposed control strategy permits the optimum control of each string of PV panels in different insolation conditions. Based on the presented mathematical analysis, an analytic constraint is derived to check the stable operation of the inverter. A modified MPPT control strategy is also proposed based on this new condition. This strategy enhances the stability margins of the system by changing the operating point of some PV arrays. In this approach, the extracted power from high power cell is reduced to prevent instability issue and to avoid injection of highly distorted current into the... 

A novel control strategy based on predictive control is presented for continuous conduction mode boost converter which operates as a power factor correction. In the proposed algorithm two horizons for the behavior of the circuit are predicted which improves the total harmonic distortion, mainly the low frequency harmonics. The algorithm doesn't need elaborating calculations therefore, implementation of the controller using low price processor is feasible. Moreover, an extra horizon of the prediction leads to expansion of the calculation time. Reduction of the harmonic distortion of the input current and improvement of the power factor have been demonstrated on an isolated boost PFC converter... 

Non-linear loads such as rectifiers are growing in industry. Three phase inverter with non-linear load can lead to highly distorted output voltage. This paper proposes a method for reducing voltage THD in three phase inverters with non-linear load. The proposed method considers the load current as a disturbance and provide a control strategy to reject it using the disturbance observer method. This method doesn't need any additional sensors or hardware and is implemented digitally in controller. Simulation results show that the presented method will reduce the total harmonic distortion of the output voltage. © 2017 IEEE  

Distribution system operators that seek operational excellence are supposed to design and implement capable processes throughout their value stream and assess how well their real services match the design specifications. Process capability analysis is a critical stage in systematic and sophisticated quality engineering approaches such as six sigma, which are based on quantitative studies. The capability of a distribution network to maintain the power quality and voltage level within an acceptable range is one of the most important aspects of design and utilisation of electricity distribution network. Capability analysis has been successfully used in the previous studies to assess the quality... 

In Z-source family inverters, shoot-through (ST) states are applied as a part of passive state in each switching cycle. The distribution of ST intervals along a switching period affects the system parameters as total harmonic distortion (THD), switching loss and common-mode voltage (CMV). In this paper, ST methods in a three-phase quasi-Z-source inverter (q-ZSI) are compared due to the CMV level. High-frequency harmonics of CMV cause leakage current flow in a transformerless grid-connected photovoltaic (PV) system. Through the comparison of the ST methods, the method with minimum CMV is identified. The experimental results are Prasented for a low voltage q-ZSI prototype. © 2018 IEEE  

This paper presents an effective hybrid optimal modulation technique for a cascaded H-bridge (CHB) multilevel inverter. The introduced method is generalized optimal pulsewidth modulation, which can be extended to any m-level CHB multilevel inverter operating at any switching frequency. The presented hybrid optimal modulation strategy includes the pattern exchange and optimal modulation techniques. In the optimal modulation technique, the hybrid interior-point algorithm, which is more flexible and efficient than conventional optimization techniques, is applied. The proposed hybrid optimal modulation strategy yields balanced units' output fundamental voltages, and low total harmonic distortion... 

Leakage current is originated from common-mode voltage (CMV) time variations in a grid-connected photovoltaic (PV) system and results in several deficiencies. In this paper, a new method is proposed for CMV reduction in a three-phase voltage source inverter (VSI) system. The proposed method is based on space vector modulation and it utilizes only odd and zero vectors. By using the proposed method, the number of fluctuations of the CMV waveform per switching cycle is reduced; therefore, the amount of high-frequency harmonics of CMV is decreased. In addition, because of applying both active and zero vectors by the proposed method, the total harmonic distortion becomes less than most of other... 

This paper proposes a straightforward control method for voltage control of a three-phase transformer-based inverter in uninterruptible power supplies or distributed generation systems. The approach offers a dual-loop design consisting inner current control loop and outer voltage loop. Sliding mode current controller provides desired bandwidth for voltage controller which consists of a state feedback term for stabilization and resonant term for harmonic damping. The proposed scheme provides fast dynamic response and low total harmonic distortion even for high power inverters with the limitations of switching frequency and LC filter components. Experimental studies for 2KVA linear and... 

Nowadays position sensors are increasingly used in many applications. One of the most commonly used sensors are resolvers. There are different types of resolvers including Wound Rotor (WR) resolvers, Variable Air-gap Length Variable Reluctance (VAGL-VR) resolvers, and Sinusoidal Rotor Variable Reluctance (SR-VR) resolvers. Regardless of the resolvers’ configurations, including linear, cylindrical and disk type, finite element analysis (FEA) is inseparable part of design and performance evaluation of these magnetic sensors. The scope of this study is to discuss challenges in the FEA of resolvers. The influence of mesh quality, time steps, stop time, excitation methods including volt-age... 

Distribution network reconfiguration as a technique for reducing network losses and enhancing voltage profile has attracted attention of many researchers. In spite of impacts network reconfiguration can have on power quality indices, the potentials have not been studied enough. To fill the gap, this paper presents a method to determine optimum network configuration considering voltage profile, network losses, and total harmonic distortion (THD). The proposed method also vouches for radial structure of the network, supplying all loads, and maintaining voltages and currents within allowable bounds. Since network reconfiguration problem is a combinatorial optimization problem, a meta-heuristic... 

A large-signal linearization method for operational transconductance amplifiers (OTA) using a combination of cross-coupled quadratic cell and a novel non-linear current injection technique is presented in this paper. Post-layout simulations show that for 180 nm CMOS process with a 1.8 V power supply, total harmonic distortion (THD) at 1.5 V peak-to-peak and 5 kHz input is less than −46 dB. Also, the dynamic range (DR) at given THD is 68 dB with power consumption of 0.64 mW. To verify the performance, the proposed OTA is used to design a new configurable filter in high-frequency range using N-path filter methodology. Universal Butterworth Gm-C active filters are embedded in the proposed... 

Nowadays, position sensors are increasingly used in many applications. One of the most commonly used sensors are resolvers. There are different types of resolvers including wound rotor resolvers, variable air-gap length variable reluctance resolvers, and sinusoidal rotor variable reluctance resolvers. Regardless of the resolvers' configurations, including linear, cylindrical and disk type, finite element analysis (FEA) is inseparable part of design and the performance evaluation of these magnetic sensors. The scope of this study is to discuss challenges in the FEA of resolvers. The influence of mesh quality, time steps, stop time, excitation methods including voltage source and current... 

Accurate position estimation is an integral part of any motion control system. Besides, instantaneous position of poles plays an important role in electronic drive system of modern PM machines. Resolvers, due to their structure, are the most reliable position sensors in harsh environments. However, resolvers are not as accurate as optical encoders in normal conditions. To increase the accuracy of these sensors, various solutions are used, such as optimization in winding arrangement, rotor and stator contour, slot-pole combinations, and improvements in resolver-to-digital converter. In this paper, fractional slot concentrated winding is used in an axial flux resolver. By the aid of winding... 

Among position sensors, resolvers are superior from reliability point of view. However, obtaining lower output voltage harmonics and simple manufacturing process is a challenge in the design and optimization of resolvers. In this paper, a metaheuristic optimization algorithm is used to minimize total harmonic distortion of the output signals, and consequently the estimated position error in concentrated coil wound field resolvers. Meanwhile, to minimize total coil numbers, manufacturing costs, and complexity of the winding process, modified objective function and constraints are proposed. In this way, a modified winding function method is employed for performance analysis of the axial flux... 

High pole number permanent magnet (PM) motors, due to their high torque density, have been receiving considerable attentions in recent years. To achieve an accurate position control in PM machines, resolvers are suggested for industrial applications. Mechanical and electromagnetic considerations in the case of high pole number resolvers lead the machine designers to choose small cores with low slot numbers. This paper proposes two different on-tooth winding configurations to achieve high pole number without increasing the slot numbers, while the accuracy of the detected position is intended to be the maximum value. Variable turn on tooth winding (VTTW) is compared with fractional slot...