Sharif Digital Repository

In this study, we have used a low temperature plasma, produced by a DC magnetron sputtering device, for decolorizing of denim fabrics, and the effect of using different gases such as Argon and Oxygen as the discharge medium have been investigated. The results obtained under equal periods of time have been compared and the effect of washing on the treated denims has been reported. © 2006 Elsevier B.V. All rights reserved  

In the present study, an aqueous root-extract of Acanthophyllum laxiusculum (AREAL) was evaluated for phenanthrene removal from two samples of contaminated soil. AREAL showed a linear solubilization enhancement for phenanthrene with a weight solubilization ratio of 0.05. Batch soil washing experiments caused the removal of phenanthrene with efficiencies of 96.7% and 78% from soils with 0.78% and 2.73% organic carbon, respectively. Desorption kinetics of phenanthrene exhibited a twophase pattern, namely, a rapid release as the initial phase and a slower removal as a subsequent phase. A two-compartment exponential model could adequately represent the two phases of the kinetic pattern of... 

This article presents the research results on production and performance of palladium-only catalytic converters. Monolith is used as catalyst carrier and gamma alumina as substrate. Dipping method is used for monolith washcoating. Palladium as the active metal is impregnated on gamma alumina using wet impregnation to produce catalyst samples. The effects of factors such as percent solid in slurry, milling time, calcination time and temperature, pH and existence of Al(NO3)3 on wash-coat characteristics were studied experimentally. SEM, XRD, and BET tests were carried out on the samples. Catalyst performance was tested in an experimental reactor that was designed for this research. The results... 

The effect of up velocity and influent COD concentration on the activity of sulphate-reducing bacteria (SRB) in UASB reactors is discussed. To study these effects, four UASB reactors were built and utilized in parallel. Examinations were carried out in two different concentrations of molasses (500 mg COD/l and 1000 mg COD/l) and four different upward flow velocities. It was observed that at velocities greater than 1 m/h, SRB bacteria were easily washed out from the reactors due to lower density and lack of ability to form dense and firm granules. It was found that in low-strength wastewaters with a COD to sulphate ratio of 2, an upward velocity in the range of 1.5-2.5 m/h could be... 

Washing the corpse and dressing the body prior to burial is an act of love and necessity in many religions. Applying robotics and automation technologies for the washing and preparation of a deceased Muslim in accordance with the Islamic Shari'at laws has been the challenging foundation of this research. With an increasing annual population growth resulting in an increase in the number of deaths (historically and/or immediately after a national disaster), automating part of this procedure to increase the speed of operation, reducing the health risks to the personnel of washing rooms "Ghassalkhaneh™ at the cemeteries and enhancing their quality of life have been the primary objectives of this... 

In this study, the effect of moving pressure source and channel parameters on the generated waves in a channel was numerically investigated; draught, angle of attack, and profile shape as parameters of pressure source, and water depth and blockage factor as channel parameters for wave height. Firstly, the chosen Computational Fluid Dynamics (CFD) approach was validated with the experimental data over a range of speeds. Then, the CFD study was conducted for further investigations. It was shown that that by enlarging draught, angle of attack, and beam of the pressure source, the wave height generated would be increased. Channel study showed that it was possible to increase the wave height... 

Polypropylene (PP) has a very low value of the surface free energy (approximately 20-25 mJ m-2). And thus, has very weak hydrophilic properties and doesn't have any affinity to any dyestuffs, such as cationic or anionic dyes. In this study, we covered some parts of PP fabrics by mask, and then irradiated them by electrons with different energies. After electron irradiation, the samples were dyed by cationic dyestuff. The result showed that, electron irradiated parts could be dyed easily and the fabric could be printed and decorated simply. The treated surfaces were investigated by scanning electron microscope (SEM), reflective spectrophotometery, and Fourier transform infrared spectroscopy... 

Physical separation methods, especially membrane technology, can be a good substitute for biological wastewater treatment, due to its simple constructions and operations. There are many papers and patents in this field. Membranes need to be cleaned periodically to be able to operate economically, and need to be replaced after a while. Several factors can influence the membrane cleaning procedure, including pressure of backwash, acid and base concentration, duration of forward washing, and duration of acid-base backwashing. In this study the effect of these parameters was investigated to find an optimum condition which could result in a good polyethersulphone (PES) membrane cleaning with less... 

Zinc-stearate-layered hydroxide nanohybrid was prepared using stearate anion as an organic guest, and zinc layered hydroxide nitrate, as a layered inorganic host by the ion-exchange method. Powder X-ray diffraction patterns and Fourier transform infrared results indicated that the stearate anion was actually intercalated into the interlayer of zinc layered hydroxide nitrate and confirmed the formation of the host-guest nanohybrid material. Also, surface properties data showed that the intercalation process has changed the porosity for the as-prepared nanohybrid material in comparison with that of the parent material, zinc hydroxide nitrate. The nanohybrid material was heat-treated at 600 °C... 

Vertically aligned multi-wall carbon nanotube (CNT) arrays were fabricated in tip-growth mode on Ni/Si substrates using plasma enhanced chemical vapor deposition. In a purification process including hydrogenation and acid washing of the Ni/CNTs, the oxygen-containing functional groups were substantially reduced and a wide hollow core at the tip of the CNTs was formed by removing the Ni seeds. Sol-gel silver nanoparticles were deposited on the surface of the unpurified Ni/CNTs, while they could also be embedded within the hollow core of the Ni-removed CNTs. The persistency of the silver ions in the Ni-removed Ag-CNTs in comparison to the release of the silver ions from the Ag-Ni/CNTs in a... 

Cotton fabrics have been prepared with smart properties by functional finishing with stimuli-responsive nano gel. A biopolymer (chitosan) and a synthetic polymer (poly-NiPAAm) have been used for the synthesis of nano gel through semi-batch surfactant-free dispersion polymerization (SB-SFDP) method. The incorporation of nano gel to textile fabrics is achieved by pad-dry-cure procedure, using an aqueous nano gel dispersion and 1,2,3,4-butantetracarboxylic acid as a crosslinking agent. With this cross linking method, it is possible to integrate the nano gel into the cotton fabric’s structure with good resistance to washing. The changes in physiological comfort parameters of cotton fabric such... 

Conjugated Linoleic Acid (CLA) was produced from castor oil using washed cells of Lactobacillus plantarum PTCC 1058 and Lactobacillus plantarum subsp. plantarum PTCC1745 as the catalyst. Under the optimal reaction conditions, the washed cells of Lactobacillus plantarum PTCC1058 produced 1661.26 mg of CLA/L reaction mixture (36% yield of production) from 4.6 mg/ml of castor oil after using 15% (w/v) cell for 121 h. The resulting CLA was a mixture of two CLA isomers, cis-9, trans-11 (or trans-9, cis-11)-octadecadienoic acid (CLA1, 44% of total CLA) and trans-10, cis-12-octadecadienoic acid (CLA2, 46% of total CLA). The total production of CLA is extracellular in all of the reactions performed... 

Reclaimed silica from spent lead-acid battery separator was exploited by pyrolysis process to avoid further extraction of raw materials and energy-consuming methods and was mixed with ultra-high molecular weight polyethylene as a matrix to fabricate a workable separator to be used in a simulated procedure in a lead-acid battery. On the other hand, fresh silica was catered and undergone similar production design to examine our product. As results showed, recycled silica after acid washing to deplete lead impurities and reaching 95.7% purity, had finer particles which contributed to some exciting functions of the separator. This microporous separator with appropriate silica dispersion, ideal... 

Copper-succinate-layered hydroxide (CSLH), a new nanohybrid material, was synthesized as an inorganic-organic nanohybrid, in which organic moiety was intercalated between the layers of a single cation layered material, copper hydroxide nitrate. Microporous scaffold carbon material was obtained by thermal decomposition of the nanohybrid at 500°C under argon atmosphere followed by acid washing process. Furthermore, the heat-treated product of the nanohybrid at 600°C was ultrafine mesoporous metallic copper particles. The results of this study confirmed the great potential of CSLH to produce the carbon material with large surface area (580m2/g) and high pore volume copper powder (2.04cm3/g)