Search for: wind-energy-conversion-system
Power System Load Frequency Control in the Presence of Wind Turbines, M.Sc. Thesis Sharif University of Technology ; Ranjbar, Ali Mohammad
This study presents the application of the doubly fed induction generator (DFIG) to reduce the frequency deviation and improve frequency of a power system. This has been done by proposing a wind turbine model and a new fuzzy controller. The fuzzy controller has been suggested to change the speed of the wind turbine rotor and modify the impacts of wind speed fluctuations on the output power. The fuzzy controller parameters are optimized using the genetic algorithm (GA) to achieve the appropriate transient response. A smart controller is combined with fuzzy controller to optimize the usage of wind turbine’s kinetic energy. Furthermore, the DFIG with the proposed controller participates in the...
Wind energy conversion system based on DFIG with open switch fault tolerant six-legs AC-DC-AC converter, Article Proceedings of the IEEE International Conference on Industrial Technology, Cape Town ; February , 2013 , Pages 1656-1661 ; 9781467345699 (ISBN) ; Zolghadri, M. R ; Poure, P ; Saadate, S ; The Institute of Electrical and Electronics Engineers (IEEE); IEEE Industrial Electronics Society (IES); IEEE Technology Management Council; IEEE Region 8; IEEE South Africa Section IE/IA/PEL Joint Chapter ; Sharif University of Technology
Continuity of service of wind energy conversion systems as well as their reliability and performances are some of the major concerns in this power generation area. Six-legs AC/DC/AC converters are normally used in modern wind energy systems like as in the system with a doubly-fed induction generator (DFIG). A sudden failure of the converter can lead to the total or partial loss of the control of the phase currents and can cause serious system malfunction or shutdown. Therefore, to prevent the spread of the fault to the other system components and to ensure continuity of service, fault tolerant converter topologies associated to quick and effective fault detection and compensation methods...
Estimation of weibull parameters for wind energy application in Iran's cities, Article Wind and Structures, An International Journal ; Volume 21, Issue 2 , 2015 , Pages 203-221 ; 12266116 (ISSN) ; Hannani, S. K ; Boroushaki, M ; Sharif University of Technology
Techno Press 2015
Wind speed is the most important parameter in the design and study of wind energy conversion systems. The weibull distribution is commonly used for wind energy analysis as it can represent the wind variations with an acceptable level of accuracy. In this study, the wind data for 11 cities in Iran have been analysed over a period of one year. The Goodness of fit test is used for testing data fit to weibull distribution. The results show that this data fit to weibull function very well. The scale and shape factors are two parameters of the weibull distribution that depend on the area under study. The kinds of numerical methods commonly used for estimating weibull parameters are reviewed. Their...
Spare parts management algorithm for wind farms using structural reliability model and production estimation, Article IET Renewable Power Generation ; Volume 10, Issue 7 , Volume 10, Issue 7 , 2016 , Pages 1041-1047 ; 17521416 (ISSN) ; Oraee, A ; Oraee, H ; Sharif University of Technology
Institution of Engineering and Technology
Doubly fed induction generators (DFIGs) are widely used in wind power systems; hence their reliability model is an important consideration for production assessment and economic analysis of wind energy conversion systems. However, to date mutual influences of reliability analysis, production estimations and economic assessments of wind farms have not been fully investigated. This study proposes a reliability model for DFIG wind turbines considering their subcomponent failure rates and downtimes. The proposed production estimation algorithm leads to an economic assessment for wind farms. A comprehensive spare parts management procedure is then presented in the study. As a case study,...
Five-leg converter topology for wind energy conversion system with doubly fed induction generator, Article Renewable Energy ; Volume 36, Issue 11 , 2011 , Pages 3187-3194 ; 09601481 (ISSN) ; Poure, P ; Saadate, S ; Zolghadri, M. R ; Sharif University of Technology
In this paper, application of a five-leg converter in Doubly Fed Induction Generator (DFIG) for Wind Energy Conversion Systems (WECS) is investigated. The five-leg structure and its PWM control are studied and performances are compared with the classical six-leg topology. The main drawback of five-leg converter with respect to the six-leg back-to-back converter is the need to increase the dc-link voltage for the same operation point, i.e. the same powers in case of WECS. So, different methods for the reduction of the required dc-link voltage in the five-leg case are studied. The five-leg converter is used to replace the conventional six-leg one, with the same ability. For the performance...
Fault Tolerant AC/DC/AC Converters for Wind Energy Turbine with Doubly-Fed Induction Generator, Ph.D. Dissertation Sharif University of Technology ; Zolghadri, Mohammad Reza ; Saadate, Shahrokh
AC/DC/AC converters are widely being used in a variety of power applications. Continuity of service of these systems, as well as their reliability and performance are now of the major concerns. Indeed, the failure of the converter can lead to the total or partial loss of the control of the phase currents and can cause serious system malfunction or even shutdown. Thus, uncompensated faults can quickly endanger the system. Therefore, to prevent the spread of the fault to the other system components and to ensure continuity of service, fault tolerant converter topologies associated with quick and effective fault detection and compensation methods must be implemented. In this thesis, the...
Open-circuit switch fault tolerant wind energy conversion system based on six/five-leg reconfigurable converter, Article Electric Power Systems Research ; Volume 137 , 2016 , Pages 104-112 ; 03787796 (ISSN) ; Saadate, S ; Poure, P ; Zolghadri, M ; Sharif University of Technology
Elsevier Ltd 2016
In this paper, an FPGA-controlled fault tolerant back-to-back converter for DFIG-based wind energy conversion application is studied. Before an open-circuit failure in one of the semiconductors, the fault tolerant converter operates as a conventional back-to-back six-leg one. After the fault occurrence in one of the switches, the converter will continue its operation with the remaining five healthy legs. Design, implementation, simulation and experimental verification of a reconfigurable control strategy for the fault tolerant six/five leg converter used in wind energy conversion are discussed. The proposed reconfigurable control strategy allows the uninterrupted operation of the converter...
FPGA-based fault tolerant scheme with reduced extra-sensor number for WECS with DFIG, Article Proceedings - ISIE 2011: 2011 IEEE International Symposium on Industrial Electronics, 27 June 2011 through 30 June 2011 ; 2011 , Pages 1595-1601 ; 9781424493128 (ISBN) ; Gaillard, A ; Poure, P ; Zolghadri, M. R ; Sharif University of Technology
Fast fault detection and converter reconfiguration is necessary for fault tolerant doubly fed induction generator (DFIG) in wind energy conversion systems (WECS) to prevent further damage and to make possible the continuity of service. Extra sensors are needed in order to detect the faults rapidly. In this paper, a very fast FPGA-based fault detection scheme is presented that minimizes the number of additional voltage sensors. A fault tolerant converter topology for this application is studied. Control and fault detection system are implemented on a single FPGA and Hardware in the Loop experiments are performed to evaluate the proposed detection scheme, the digital controller and the fault...