Sharif Digital Repository

In this study, an experimental investigation was conducted from a thermal performance standpoint on closed-loop pulsating heat pipes (CLPHPs) with four different fluids and their water-based binary mixtures as working fluids with volume mixing ratios of 3:1, 1:1, and 1:3. Ethanol and acetone as two types of fluids that are soluble in water and, to unprecedentedly compare the behavior of insoluble mixtures with the soluble ones as the working fluids, toluene and hexane as two types that are insoluble in water were used. Additionally, to predict the thermal performance of the pure, soluble binary, and insoluble binary fluids simultaneously for the first time, a correlation was derived. © 2018... 

In this study, an experimental investigation was conducted from a thermal performance standpoint on closed-loop pulsating heat pipes (CLPHPs) with four different fluids and their water-based binary mixtures as working fluids with volume mixing ratios of 3:1, 1:1, and 1:3. Ethanol and acetone as two types of fluids that are soluble in water and, to unprecedentedly compare the behavior of insoluble mixtures with the soluble ones as the working fluids, toluene and hexane as two types that are insoluble in water were used. Additionally, to predict the thermal performance of the pure, soluble binary, and insoluble binary fluids simultaneously for the first time, a correlation was derived. © 2018,... 

The increment of using fossil fuels has caused many perilous environmental problems such as acid precipitation, global climate change and air pollution. More than 50% of the energy that is used in the world is wasted as heat. Recovering the wasted heat could increase the system efficiency and lead to lower fuel consumption and CO2 production. Organic Rankine cycle (ORC) which is a reliable technology to efficiently convert low and medium temperature heat sources into electricity, has been known as a promising solution to recover the waste heat. There are numerous studies about ORC technology in a wide range of application and condition. The main objective of this paper is to presents a... 

In the present research an experimental investigation is performed to explore the effects of working fluid, heat input, ferrofluid concentration, magnets location, and inclination angle on the thermal performance of an Open Loop Pulsating Heat Pipe (OLPHP). Obtained results show that using ferrofluid can improve the thermal performance and applying a magnetic field on the water based ferrofluid decreases the thermal resistance. It shows that at an inclination angle of the OLPHP to be zero, the thermal performance of the present OLPHP reduces. Best heat transfer capability was achieved at 67.5 degree relative to horizontal axis for all of working fluids. Variation of the magnets location... 

In this work, a four-turn Pulsating Heat Pipe (PHP) is fabricated and tested experimentally. The novelty of the present PHP is the capability of obtaining various thermal performances at a specific heat input by changing the magnetic field. The effects of working fluid (water and ferrofluid), charging ratio (25%, 40%, and 55%), heat input (25, 35, 45, 55, 65, 75, and 85 W), orientation (vertical and horizontal heat mode), and magnetic field on the thermal performance of PHPs are investigated. The results showed that applying the magnetic field on the water based ferrofluid reduced the thermal resistance of PHP by a factor of 40.5% and 38.3% in comparison with the pure water case for the... 

A novel rotary magnetohydrodynamic (MHD) (RMHD) micropump is presented in this paper in order to both benefit exclusive advantages from the MHD micropumps and eliminate the current obstacles in their implementation. Lorentz force, which is the actuation mechanism in RMHD, is used to propel a mercury slug in a circular microchannel in order to suck the working fluid from the inlet and pump it to the outlet. This idea is integrated with a valve which prevents the working fluid from passing through, while allowing the mercury slug to pass, during each pumping loop. The performance of a fabricated RMHD is evaluated, considering parameters such as pressure difference, running duration, electric... 

Pulsating heat pipe (PHP) is a type of wickless heat pipe that has a simple structure and an outstanding thermal performance. Nanofluid is a type of fluid in which nanoparticles are dispersed in a base fluid and have generally a better thermal conductivity in comparison with its base fluid. In this article, the performance of a nanofluid PHP is investigated. Graphene/water nanofluid with a concentration of 1 mg mL−1 and TiO2 (titania)/water nanofluid with a concentration of 10 mg mL−1 are used as the working fluids. To simultaneously investigate the thermal performance and flow regimes in the PHP, a one-turn copper PHP with a Pyrex glass attached to its adiabatic section is used. A one-turn... 

Pulsating heat pipe (PHP) is a type of wickless heat pipe that has a simple structure and an outstanding thermal performance. Nanofluid is a type of fluid in which nanoparticles are dispersed in a base fluid and have generally a better thermal conductivity in comparison with its base fluid. In this article, the performance of a nanofluid PHP is investigated. Graphene/water nanofluid with a concentration of 1 mg mL −1 and TiO 2 (titania)/water nanofluid with a concentration of 10 mg mL −1 are used as the working fluids. To simultaneously investigate the thermal performance and flow regimes in the PHP, a one-turn copper PHP with a Pyrex glass attached to its adiabatic section is used. A... 

The effect of working fluid inventory and heat input on the performance of thermosyphon is investigated in this paper. First, a thermosyphon with diameter of 16 mm made of steel with toluene as working fluid and the length of the evaporator, adiabatic and condenser section 10, 23 and 17 cm was considered, respectively. The working fluid inventory was considered 0.1, 0.14, 0.18 and 0.24 of total volume of thermosyphon and in each case 54–235 W of heat input applied to the evaporator area also. In order to evaluate the transient behavior of the thermosyphon, in any amount of working fluid, 28 W of heat input was considered and temperature of the evaporator area were recorded at different... 

The present work investigates the thermal performance of a five turn Open Loop Pulsating Heat Pipe (OLPHP). The effects of working fluid namely water and ferrofluid, heat input, ferrofluid concentration, charging ratio, and orientation will be considered. Experimental results show that using ferrofluids can enhance the thermal performance in comparison with the case of distilled water. In addition, applying a magnetic field on the OLPHP charged with ferrofluid reduces its thermal resistance. Variation of the ferrofluid concentration results in different thermal performance of the OLPHP. Best charging ratio for the distilled water and ferrofluid without magnetic field is 60 % in most of the... 

Pulsating Heat Pipes are an effective mean for heat removal with the potential for a widespread application in electronic packaging. An experimental study a Closed Loop Pulsating Heat Pipe (CLPHP) constructed of copper tubes formed into four meandering turns is presented. Once configured in a vertical orientation the lower portion of the CLPHP comes in contact with a heat source (called the evaporator) from which it will remove heat through the pulsating action of the two-phase mixture contained within the initially evacuated copper tubes eventually transfer the heat to a heat sink (known as the condenser). Heat fluxes can be measured using temperature data gathered from experiments.... 

In this study, the aim is to investigate the application of pulsating heat pipes (PHPs) as a heat transfer tool in a solar water heater (SWH). For this purpose, an extra-long pulsating heat pipe (ELPHP) is designed, constructed and installed in a thermosyphon solar water heater. In this work the ELPHPs are made of copper tubes of internal diameter 2.0. mm. The number of meandering turns is 6 and the working fluid employed is distilled water. The lengths of condenser and evaporator sections are 0.8 and 0.96. m, respectively. The length of adiabatic section varies between 0.7 and 1.8. m. Inclination of the ELPHPs varies between 15° and 90° but is 45° for evaporator section. Four different... 

The present study attempts to use the methanol-silver nanofluid filled heat pipe heat exchanger and compares the effectiveness as well as the energy saving with pure methanol. A heat pipe heat exchanger has been tested in a test rig under steady-state conditions. The lengths of both the evaporator and the condenser sections of the heat exchanger were 700 mm, and its central adiabatic section had a length of 160 mm. The heat exchanger had 36 plate finned copper thermosyphons arranged in three rows. The inlet air temperature across the evaporator section was varied in the range of 33-43 °C while the inlet air temperature to the condenser section was nearly constant to be 13 °C. First, pure... 

In this work, a four-turn pulsating heat pipe (PHP) is fabricated and tested experimentally. The novelty of the present PHP is the capability to obtain various thermal performances at a specific heat input by changing the magnetic field. The effects of working fluid (water and ferrofluid), charging ratio (40% and 70%), heat input (35, 45, 55, 65, 75, and 85 W), orientation (horizontal and vertical heat mode), ferrofluid volumetric concentration (2.5% and 7%), and magnetic field on the thermal performance of PHPs are investigated. The results showed that applying the magnetic field on the water-based ferrofluid reduced the thermal resistance of PHP in all orientations. In the presence of a... 

The bio-microfluidic systems are usually encountered with non-Newtonian behaviors of working fluids. The rheological behavior of some bio-fluids can be described by differential viscoelastic constitutive equations that are related to PTT and FENE-P models. In the present work, thermal transport characteristics of the steady fully developed electroosmotic flow of these fluids in a slit microchannel with constant wall heat fluxes have been investigated. The Debye-Huckel linearization is adopted and the effects of viscous dissipation and Joule heating are taken into account. Analytical solutions are obtained for the transverse distributions of velocity and temperature and finally for Nusselt... 

In this paper, the effect of different parameters on the thermal operation of a Closed Loop Pulsating Heat Pipe (CLPHP) has been investigated. These parameters include the working fluid, the inclination angle, the filling ratio, and the input heat flux. The effect of nanoparticle mass concentrations has been analyzed as well. It was observed that the CLPHP can decrease thermal resistance up to 11.5 times compared to the same empty copper tube with thermal resistance of 9.4 K/W. Optimum thermal operation for a system with the water-silver nanofluid was achieved at conditions of the 50% filling ratio with thermal resistance of 0.9 K/W, and for the water-titanium oxide system, the optimal... 

This work concerns with experimental and analytical investigation of role of ultrasonic wave radiation in relative permeability of both wetting and non-wetting phases in a free gravity drainage process in porous media under the influence of ultrasonic wave. Glass beads ranged from 70 to 100 mesh sizes were packed and used in the tests. The working fluids consist of distilled water, kerosene and Doroud and Paidar crude oils as wetting and air as non-wetting phase. The measured oil recovery data along with Hagoort (1984) backward methodology were used to determine and to compare the relative permeability of wetting phases in presence and absence of ultrasonic radiation. In addition, the... 

Thermopneumatic micropump is one type of positive displacement micropump, which has many applications due to its relatively large stroke volume, low working voltage, and simple fabrication in microscale. In this paper, a numerical study of heat transfer and fluid flow in a valveless thermopneumatically driven micropump is presented. For rectifying the bidirectional flow, a nozzle and a diffuser are used as the inlet and outlet channels of the chamber. Since the fluid flow is induced by the motion of a diaphragm, the numerical simulation includes fluid structure interaction, which requires applying a dynamic mesh. The domain of solution is divided into two sections; the actuator unit, which...