Sharif Digital Repository

LLC resonant converter has been widely used in dcdc converters. In this paper, optimum dead-time and maximum switching frequency of a wide-adjustable-range LLC resonant converter are investigated for realizing the zero voltage switching (ZVS) operation even under the worst-case conditions. Analyses demonstrate that these parameters depend on the converter inductance ratio and ratio of the converter resonant capacitor and the effective capacitance appeared in parallel with the drainsources of the power MOSFETs. The necessary dead time for realizing the ZVS operation can be minimized by choosing the normalized maximum switching frequency, properly. Using the dead-time optimum value, soft... 

LLC resonant converter with significant resonant inductance is proposed for designing an adjustable wide-range regulated voltage source. Large resonant inductance increases output voltage adjustment range and conversion efficiency, particularly at light loads. Soft switching is achieved for all power devices under all operating conditions by choosing the dead time and maximum switching frequency properly and operating in the converter's inductive region. Using a power-factor-correction (PFC) converter reduces the resonant converter's output voltage dependence to the variations of the main ac input voltage. Thus, the compensation of the load variations and the wide-range adjustment of the... 

In this paper, a new zero-voltage-switching, high power-factor, bridgeless rectifier is introduced. In this topology, an auxiliary circuit provides soft switching for all of the power semiconductor devices. Thus the switching losses are reduced and the highest efficiency can be achieved. The proposed converter has been analyzed and a design procedure has been introduced. The control circuit for the converter has also been developed. Based on the given approach, a 250 W, 400 Vdc prototype converters has been designed at 100 kHz for universal input voltage (90-264 Vrms) applications. A maximum efficiency of 94.6% and a power factor correction over 0.99 has been achieved. The simulation and... 

Today's technology is going to be switched to power electronics equipment due to their wide applications in industries. Their development is too fast since the electronic and microprocessor technology promoted together, which play a significant role in this issue. In this paper, a novel boost converter with an h-bridge auxiliary LCC resonant circuit which provides soft switching technique to the converter is introduced. Then different modes of its operation are investigated and key parameters of the converter are extracted. Finally, simulation analyses are carried out to validate each mode's equation. In this study, the proposed structure of auxiliary circuit permits converter to work in... 

LLC resonant converter is one of the most suitable circuit topologies that have been introduced for designing constant output voltage switched-mode power supplies. In this paper, a design procedure is introduced for using this converter as a wide output range voltage source. Unlike constant output voltage applications which need small converter inductance ratio and narrow switching frequency variations, for wide output range applications, large values of these parameters are needed simultaneously and should be optimized. Instead of minimizing the components stresses, leading to a great value of the inductance ratio, proper choice of the converter parameters resulting in a smaller inductance... 

In this paper, a novel zero-voltage-switching topology for power factor correction bridgeless boost rectifier is proposed. By employing an improved switch cell, ZVS for all the main switches is achieved without additional current or voltage stress. The zero-current-switching is also provided for the auxiliary switch. In all modes of operation of this converter, the input current flows through only two semiconductors. Therefore, conduction loss of this converter is as low as the conventional parent converter. With these features, the efficiency of the proposed converter is very high. A 500 W prototype is designed and simulated to verify the system performance  

Simplified equations are used for the analysis of a dual active bridge converter leading to a conservative estimation of the zero voltage switching (ZVS) region. The ZVS is directly affected by the inserted deadband in each leg of the converter. In this paper the impact of the ZVS capacitor and deadband on soft switching region for this converter is analyzed. Also, the sufficient constraints for ZVS condition in the input and output bridges are determined by analyzing the circuit behavior during the bridges deadband. Simulation results of a 700V-350V, 50-kW DC-DC converter validate the analysis. © 2017 IEEE  

This paper presents an analytical model to design a class-E power amplifier under only zero-voltage-switching (ZVS) term with the MOSFET nonlinear drain-source shunt parasitic capacitance that is named as the subnominal operation. The presented analysis is performed under any grading coefficient m of MOSFET body junction diode and any duty ratio D. The grading coefficient m along with the switching duty ratio D are implemented as tuning variables to satisfy design specifications and ZVS term simultaneously. The restriction of selecting the value of m and D for the subnominal operation has a major effect on simultaneously satisfying of load-resistance, operating frequency, and junction... 

Multi-port converters (MPC), used in multi-input/multi-output power electronic systems have low cost, low weight and low mass integrated control system. Besides these converters offer bidirectional and isolated ports, which are inevitable in some applications. Three-Port Half Bridge Converters (TPHBC) are the ones which have the lowest component count. But these converters suffer from a low Zero Voltage Switching (ZVS) range that is lost in medium to low load powers. Low ZVS range cause low efficiency, especially in low output powers. In this paper a modified Pulse Width Modulation (PWM) technique is introduced to increase the ZVS range of main switches which results higher efficiency and... 

This paper proposes a new variable frequency zero voltage switching (ZVS) control method for boost converter operating in boundary conduction mode (BCM). The intended method keeps the converter in BCM despide of the load and input voltage variations. This is done by changing switching frequency in a certain specified range. The proposed method can guarantee circuit performance in BCM via zero-crossing detection of the inductor current and changing the switching frequency. In addition, with a slight modification in control structure, it is possible to achieve a fully ZVS in all cases. This converter control is carried out in analog form without using microprocessors which, compared with the... 

In this study, a new isolated high-gain switched-boost DC/DC converter employing two symmetrical switched-boost networks along with a modified control algorithm based on the combination of the pulse-width modulation (PWM) and phase-shift modulation is proposed. Utilising symmetrical switched-boost networks increase the voltage gain of the proposed converter, significantly. Moreover, applying the proposed switching algorithm on the proposed isolated switched-boost DC/DC converter leads to the following advantages: (i) high-voltage gain, (ii) zero voltage switching (ZVS) turn-on of two switches, (iii) ZVS turnoff of two switches and (iv) appearing three controllable parameters (the... 

Power density is an influential factor in 400 volt telecom energy distribution systems. In addition, systems are desired to reach an acceptable efficiency while they take advantage of a galvanic isolation. This paper presents a new architecture that is based on push pull topology and its power switches perform ZVS in both their turn on and turn off conditions. Besides, the presented topology uses an interleaving technique that has made it desirable for high power applications. Power loss for the presented topology is calculated and compared to conventional topologies. Finally, by considering the efficiency and power density of the presented topology, it is concluded why this topology is... 

In this study, a new LLC resonant converter for high-voltage high-power applications is introduced. The introduced power converter is a two-phase interleaved full-bridge based that uses a transformer with secondary and tertiary windings to obtain higher output voltage. Zero voltage switching (ZVS) at MOSFETs turn on and zero current switching (ZCS) for all the output diodes at turn off are achieved for a wide range of input voltage (100 V-200 V) and output power (200 W-1500 W) variations. Simulation results show a 95% peak efficiency. © 2021 IEEE  

A new high step-up boost converter with an active clamp circuit to eliminate voltage spike caused by leakage inductor is introduced in this paper. The introduced power converter has a high voltage gain for variable input voltage from 48V to 80V. Since both main and auxiliary switches turn on with zero voltage switching (ZVS) and all the diodes turn off under zero current switching (ZCS) condition, switching losses and EMI noises are strongly degraded. Therefore, the converter's efficiency is improved significantly. Simulation results show a 96.4% peak efficiency and 95.4% average efficiency. The proposed topology is suitable for low-input-voltage and low-output power applications such as... 

LLC resonant converter has been used widely as dc-dc converter for achieving constant dc voltage. In this paper, an LLC resonant converter, by adding an inductance to its conventional topology and considering the rectifying stage stray inductances, is proposed for an adjustable wide range regulated current source (20-200 A dc) for using as ion implanter's filament power supply. The additional inductor increases output current adjustment range and efficiency, especially at light loads. Transformer's leakage inductances and rectifying stage stray inductances have been considered. Because of these inductances, the rectifier stage always works in continuous conduction mode, and its conduction... 

In this paper, the FHA and a simple TDA approaches have been used to derive the normalized maximum switching frequency of wide adjustable range LLC resonant converter for realizing the ZVS operation even under the worst-case conditions. By accounting the resonant current higher harmonics, more accurate expressions are derived. These analyses demonstrate that the normalized maximum switching frequency depends on the dead-time and the converter inductance ratio. It also depends on the ratio of the converter resonant capacitor and the effective capacitance appeared in parallel with the power MOSFETs drain-sources. The simulated and experimental results are in good agreement with the derived... 

LLC-LC resonant converter is a suitable circuit topology to design switched-mode power supplies for wide-output-voltage and wide-output-load applications. In this paper, a design procedure is introduced to optimize this converter. Unlike soft switching techniques for pulse width modulated converters, which usually apply an active auxiliary circuit to reduce switching losses and EMI, in the proposed converter, not only such circuits are not used, but also all of the parasitic elements are merged to the converters main components. Zero-voltage switching (ZVS) operation is realized for all power devices under all operating conditions. Thus, this converter is a suitable choice for... 

Switched Reluctance Motors (SRMs) are widely used in high-speed and low voltage applications because of their attractive features such as robustness and simplicity. No winding on the rotor of this type of motors allows reaching high speed which is desired for many applications. Drive circuits of SRMs also play an important role in their performance and operation. In this paper, a new bifilar drive circuit for this type of motors has been proposed. This novel configuration has been tested and investigated by PSIM software. Results show that the new bifilar drive circuit highly reduces the voltage stresses on semiconductor switches, and also considerably reduces the switching losses which are... 

The demand for bidirectional DC/DC converters is increasing because of their potential capability for sustainable energy conversion systems where the power is to be captured from or stored in energy storage elements. This paper presents a three-phase series resonant bidirectional converter which is suitable for high power applications. The converter consists of two three-phase full bridge networks, the resonant tanks and a high frequency three-phase transformer. All switches can work either in ZVS or ZCS mode. The voltage drop on leakage inductances is minimized by choosing the switching frequency close to the resonant frequency, allowing high efficient power conversion. The phasor analysis...