Sharif Digital Repository

In this study, titanium substrates which previously oxidized through Micro arc oxidation method, was coated by Hydroxyapatite (HAp) coating once more by means of the same method. Morphology, topography and chemical properties as well as phase composition and thickness of layers were studied to reveal the effect of the electrolyte concentration on coating features. According to results, the obtained coatings are consisted of HAp and titania as the major phases along with minor amounts of calcium titanate and α-tri calcium phosphate. Ca and P are present on surface of obtained layers as well as predictable Ti and O based on the XPS results. Thickness profile of coatings figured out that by... 

Micro Arc Oxidation (MAO) process was utilized to fabricate nano bioceramic TiO 2-hydroxyapatite coatings on titanium substrates. Samples were produced in electrolytes contained 1 g/l β-glycerophosphate and 5, 10 and 15 g/l calcium acetate for 3, 6 and 10 min at 350 V. The techniques including XRD, XPS, SEM, FESEM and EDX were employed to study the effect of processing parameters. Hydroxyapatite, anatase, α-tri calcium phosphate and calcium titanate phases as well as 30-60 nm-size crystals were detected in the coating layer. It was also observed that the pore volume would increase by increasing the electrolyte concentration. The growth time was also found to influence the total pore volume.... 

Electrophoretic technique was used to deposit micro- and nano-sized aluminum nitride coatings on stainless steel surfaces by using a well-dispersed stable suspension produced by addition of AlN powder plus a small amount of iodine to ethanol. Parabolic regime governed the deposition. Electrophoretic deposition for 240 s at 100 V resulted in formation of a uniformly dense film on the top, but a porous inhomogeneous layer at the bottom. This was attributed to fast deposition of coarse particles and/or agglomerates at large electric fields. After drying, micro-sized particles led to a uniform crack-free interface while nano-particles resulted in fragmented non-cohesive layers. Weight loss... 

Zeolite-based micromotors were developed to eliminate the biological and chemical contamination of water in a fast and efficient way. The motors consist of a silver-exchanged zeolite core and a partial catalytic coating. These porous engines showed rapid killing of Pseudomonas aeruginosa bacteria cells in a very short time, less than 7.5 minutes. The heavy metal uptake of the zeolitic motors during the first 20 minutes of contact was considerably higher than that of zeolite particles by 23% for Pb2+, 19% for Co2+, and 16% for Ni2+. Also, the maximum removal efficiency of the motors (at room temperature and for 6 hours) for Pb2+, Co2+, and Ni2+ was 93%, 87%, and 78%, respectively, higher than... 

In the present research, the introduction of multi-walled carbon nanotubes (MWCNTs) into the hydroxyapatite (HA) matrix and dip coating of nanocomposite on titanium alloy (Ti-6Al-4V) plate was conducted in order to improve the performance of the HA-coated implant via the sol-gel method. The structural characterization and electron microscopy results confirmed well crystallized HA-MWCNT coating and homogenous dispersion of carbon nanotubes in the ceramic matrix at temperatures as low as 500 C. The evaluation of the mechanical properties of HA and HA/MWCNT composite coatings with different weight percentages of MWCNTs showed that the addition of low concentrations of MWCNTs (0.5 and 1 wt.%)... 

This paper describes the effects of using direct and pulse current on composition and corrosion resistance of Fe-Ni-Cr alloy coatings. In both direct and pulse current electrodeposition, increasing the current density has a decreasing effect on Fe and Ni and an increasing influence on Cr. In pulse current electrodeposition, duty cycle has a greater effect than frequency on composition of the alloy coating, particularly in the range of 10-50%. In this range, by increasing the duty cycle, Ni decreases, Fe sharply increase and Cr shows an increasing trend. Following a study of the microhardness of coatings, it is determined that the microhardness increases about 1.5 times by pulse current... 

In this paper, the so-called small time-step instability in finite element simulation of the fluid part is considered in fluid-structure interaction (FSI) problems in which a high-frequency vibrating structure interacts with an incompressible fluid. Such a situation is common in many microfluid manipulating devices. A treatment has been proposed that uses the dimensionless set of FSI governing equations in order to scale up the problem time step to a proper level that precludes the potential small time-step instability. Two-dimensional and three-dimensional finite element simulations of a mechanical micropumping device are performed to verify the efficiency of the presented approach. Solid... 

The fracture toughness and deformation mechanism of PP/CaCO3 (15 wt.%) composites were studied and related to load-bearing capacity of the particles. To alter the load-bearing capacity of the particles, different particle sizes (0.07-7 μm) with or without stearic acid coating were incorporated. The fracture toughness of the composites was determined using J-Integral method and the deformation mechanism was studied by transmission optical microscopy of the crack tip damage zone. It was observed that the load-bearing capacity of the particles decreased by reduction of particle size and application of coating. A linear relationship between normalized fracture toughness and inverse of... 

Corrosion of steel rebars in concrete can reduce the durability of concrete structures in coastal environments. The corrosion rate of these concrete structures can be reduced by using suitable concrete additives and coating on rebars. This paper investigates the corrosion resistance of steel rebars by the addition of pozzolanic materials including fly ash, silica fume, polypropylene fibers, and industrial 2-dimethylaminoethanol (FerroGard 901) inhibitors to the concrete mixture. Three different types of rebars including mild steel rebar st37, and two stainless steel reinforcements, AISI 304 and AISI 316, were used. Various types of primer and coating including alkyd based primer, hot-dip... 

Electrochemical co-deposition approach was expanded to prepare composite bio-ceramic coating of hydroxyapatite (HA)/polyvinyl acetate on the surface of titanium. The role is to improve the bioactive and crystallization properties. The results of XRD, XPS, SEM and TEM characterization showed that by increasing amount of vinyl acetate in the composite bio-ceramic coating before and after immersing in the simulated body fluid (SBF), an oriented growth of HA planes on the (0 0 2) direction had been observed on titanium substrate. Also significant surface morphology changes were obtained  

The aim of this research is to obtain composite coatings of bronze (90% Cu-10% Sn) with graphite particles. The electrodeposition of G-Cu (Sn) composites from an alkaline bath containing cyanide is described. Composite coatings consisting of graphite particles and copper-tin were prepared by means of the conventional electrocodeposition (CECD) and sediment codeposition (SCD) techniques. The graphite particles involved were less than 10 μm. The dependence of graphite amount in the composite coatings was investigated in relation to the graphite concentration in bath, cathode current density, stir rate and technique type and it was shown that these parameters strongly affected the volume... 

Titanium is a highly reactive metal with an inclination to compose with oxygen. In order to increase its corrosion resistance and application, therefore, a thin layer of titanium oxide is produced on the surface by chemical and electrochemical methods. In the present research, titanium has been anodized in 20 M of NaOH solution under potentiostatic conditions at constant voltages of 25 and 35 V. The microstructure of the anodic layers has been studied by the use of a Scanning Electron Microscope (SEM) and X-Ray Diffraction (XRD). The results indicated that the structure of the anodic layers is amorphous with low porosity and that thickness increases with an increase in anodizing voltage. The... 

A hierarchical superhydrophobic surface is prepared via a two-step boiling water immersion process and anodization of the treated aluminum substrate in a novel hydrophobic electrolyte of aluminum nitrate and stearic acid mixture at room temperature. The immersion time in boiling water had a significant influence on the morphology and durability of the sample. A pseudoboehmite coating is created on the aluminum surface during the boiling process, as revealed by the field emission scanning electron microscopy (FE-SEM) and Fourier transform infrared (FTIR) spectrophotometer results. The energy-dispersive x-ray spectroscopy analysis confirmed the formation of hydrophobic coating surface after... 

Line nanopatterns are produced on the positive photoresist by scanning near-field optical microscope (SNOM). A laser diode with a wavelength of 450 nm and a power of 250 mW as the light source and an aluminum coated nanoprobe with a 70 nm aperture at the tip apex have been employed. A neutral density filter has been used to control the exposure power of the photoresist. It is found that the changes induced by light in the photoresist can be detected by in situ shear force microscopy (ShFM), before the development of the photoresist. Scanning electron microscope (SEM) images of the developed photoresist have been used to optimize the scanning speed and the power required for exposure, in... 

Finesmigration is a noticeable problem in petroleum-production engineering. Plugging of throats in porous media occurs because of detachment of fine particles from sand surfaces. Thus, the study of interactions between fines and pore surfaces and the investigation of governing forces are important factors to consider when describing the mechanism of the fines-release process. The main types of these forces are electric double-layer repulsion (DLR) and London-van der Waals attraction (LVA). It may be possible to alter these forces with nanoparticles (NPs) as surface coatings. In comparison with repulsion forces, NPs increase the effect of attraction forces. In this paper, we present new... 

To improve the biocompatibility and corrosion resistance of 316L SS (Stainless Steel) metal implants, HAp(hydroxyapatite)/TiO2/Al2O3 nanocomposite coating was created using dip sol-gel method sintered at 550 °C. The weight percentage of TiO2+ Al2O3 in these coatings was 20, 30, and 40% wt. In this study, characterization was performed using FTIR (Fourier-Transform Infrared Spectroscopy), XRD, FE-SEM (Field Emission Scanning Electron Microscope), EDS (Energy Dispersive Spectroscopy), DLS (Dynamic Light Scattering), Pull-off, and AFM (Atomic Force Microscopy) analysis. The potentiodynamic polarization and EIS (Electrochemical Impedance Spectroscopy) were performed in the simulated body fluid... 

Biocompatibility materials such as Ti6Al4V alloy have many medical applications, but their corrosion resistance and antibacterial properties are low, which limits their medical application. Therefore, to improve these challenges in this study, HAp + 15 wt% TiO2 + 5 wt% Ag nanocomposite coating was applied on Ti6Al4V/TiO2 substrate by sol-gel dip method and sintered at 550 °C. The TiO2 layer was pre-formed on the Ti6Al4V substrate using the gel-sol process. The results showed that the nanocomposite was synthesized correctly, and the particle size was in range of 40–90 nm. The evaluation of the coatings developed showed that TiO2/HAp + 15 wt% TiO2 + 5 wt% Ag coating had higher adhesion... 

To improve the biocompatibility and corrosion resistance of 316L SS (Stainless Steel) metal implants, HAp(hydroxyapatite)/TiO2/Al2O3 nanocomposite coating was created using dip sol-gel method sintered at 550 °C. The weight percentage of TiO2+ Al2O3 in these coatings was 20, 30, and 40% wt. In this study, characterization was performed using FTIR (Fourier-Transform Infrared Spectroscopy), XRD, FE-SEM (Field Emission Scanning Electron Microscope), EDS (Energy Dispersive Spectroscopy), DLS (Dynamic Light Scattering), Pull-off, and AFM (Atomic Force Microscopy) analysis. The potentiodynamic polarization and EIS (Electrochemical Impedance Spectroscopy) were performed in the simulated body fluid... 

Biocompatibility materials such as Ti6Al4V alloy have many medical applications, but their corrosion resistance and antibacterial properties are low, which limits their medical application. Therefore, to improve these challenges in this study, HAp + 15 wt% TiO2 + 5 wt% Ag nanocomposite coating was applied on Ti6Al4V/TiO2 substrate by sol-gel dip method and sintered at 550 °C. The TiO2 layer was pre-formed on the Ti6Al4V substrate using the gel-sol process. The results showed that the nanocomposite was synthesized correctly, and the particle size was in range of 40–90 nm. The evaluation of the coatings developed showed that TiO2/HAp + 15 wt% TiO2 + 5 wt% Ag coating had higher adhesion... 

To improve the biocompatibility and corrosion resistance of 316L SS (Stainless Steel) metal implants, HAp(hydroxyapatite)/TiO2/Al2O3 nanocomposite coating was created using dip sol-gel method sintered at 550 °C. The weight percentage of TiO2+ Al2O3 in these coatings was 20, 30, and 40% wt. In this study, characterization was performed using FTIR (Fourier-Transform Infrared Spectroscopy), XRD, FE-SEM (Field Emission Scanning Electron Microscope), EDS (Energy Dispersive Spectroscopy), DLS (Dynamic Light Scattering), Pull-off, and AFM (Atomic Force Microscopy) analysis. The potentiodynamic polarization and EIS (Electrochemical Impedance Spectroscopy) were performed in the simulated body fluid...