Sharif Digital Repository

Typical non-hydrocarbon gases, which have been utilized in miscible and immiscible processes, are carbon dioxide and nitrogen. These gases are usually injected separately and have been rarely utilized together as a tertiary recovery process. In this article, the authors have experimentally focused on sequential carbon dioxide and nitrogen gas injection as a new enhanced oil recovery method. The periodic injections of carbon dioxide and nitrogen have been repeated for six injection pore volumes. Sensitivity analysis of injection pressure, injection volume, and injection rate has also been investigated in core flood experiments. The experimental results have revealed that a sequential miscible... 

Gas injection is the second largest enhanced oil recovery process being applied in many reservoirs around the world. Simulation of these processes is necessary for implementation, management, and decision making. Relative permeability is one of the most important factors in numerical reservoir simulation. In this study, several core flood experiments are done and the relative permeability in carbon dioxide (CO2) injection is compared with nitrogen (N2) injection. Oil relative permeability in CO 2 injection is found to be higher than in N2 injection, but gas relative permeability in CO2 injection is found to be lower than in N2 injection. Higher oil relative permeability in CO 2 injection... 

During any microbial enhanced oil recovery process, both cells and the metabolic products of bacteria govern the tertiary oil recovery efficiency. However, very accurate examination is needed to find the functionality of these tiny creatures at different reservoir conditions. In this regard, the effect of cell structure on ultimate microbial recovery efficiency which is the most dominant mechanism based on the microorganism types (gram-negative or gram-positive) was systematically investigated. At the first stage, possible different active mechanisms using Bacillus stearothermophilus SUCPM#14 strain were tested using specially designed injection protocol, in situ and ex situ core flooding... 

Anatase and amorphous TiO2 nanoparticles were used to improve recovery of heavy oil from sandstone cores. Before performing core floods, the stability of nanoparticles at different salinities was tested using ζ potential and ultraviolet-visible (UV-vis) methods. While water recovered only 49% of the oil in the core flood experiments, 0.01% anatase structure solution recovered 80% of the oil after injecting two pore volumes at optimum conditions. To understand the mechanism responsible for improved recovery, contact angle measurements were performed on the rock surface before and after treatment with the nanoparticle solution. Contact angle measurements showed that the rock wettability... 

This paper studies a WAG process for improving the recovery efficiency in light oil reservoirs. Until now, few references have reported the role of CO2 mole percent on recovery improvement in light oil reservoirs. The injected gas was changed, and the effect of composition changes on performance of core flood experiments were conducted at fixed flow rate. Five series of experiments (varied in methane mole percentages, 0, 25, 50, and 75, 100) were systematically examined. The results indicated that the oil recovery efficiency improved with the increasing of CO2 mole ratio and there was also maximum recovery efficiency in this work. That would be helpful to better understanding the role of CO2... 

The use of water-alternating-gas injection can potentially lead to improved oil recovery from the fields; simultaneous water and gas injection is a form of water-alternating-gas injection. However, there is still an incomplete understanding of these processes and the need for comparative work is inevitable. Core flood experiments and compositional simulations of water-alternating-gas and simultaneous water and gas processes are presented. Immiscible, near miscible, and miscible modes of injection are covered. Matching process is done and optimization of design parameters (injection rate, slug size, water-alternating-gas ratio, and injection gas) is performed. Experimental data demonstrate... 

This work concerns with experimental investigation of CO2 WAG injection to light crude oil in near miscible conditions which has been rarely attended in the available literature. Here, several core flood experiments at three constant injection rates and four WAG ratios are conducted on sandstone rocks saturated with light crude oil in presence of saline water. The results showed that higher injection rate has a better performance regarding oil recovery for smaller PVs of injected fluids, while lower injection rate showed higher ultimate recovery for a 30% increase in injected PVs. Secondary continuous gas injection showed a superior performance than all the other WAG injections in different... 

In this work effect of composition changes of injection gas, CH4 + CO2, on the performance of immiscible WAG injection in light oil, 41 oAPI, which has been rarely attended in the available literature is investigated. Presence of CO2 helps to reduce the MMP of CH4 significantly. Core flood experiments are conducted at reservoir conditions and fixed flow rate of 0.5cc/min on a sandstone sample with the brine concentration of 5000 ppm, and the influence of injection gas composition as well as WAG ratio on oil recovery is investigated. Different mole percents of methane in mixture, 0%, to 100% are examined, and the tests continued to ten alternate cycles with a slug size of 0.1 pore volumes and... 

Despite previous researches on ion-engineered waterflooding (IEWF), its underlying mechanisms are not fully understood, particularly in presence of additives, like surfactants. This paper concerned with the contribution of Ca 2+ , Mg 2+ , SO 4 2- and Na + into altering wettability of oil-wet carbonate minerals towards water preferred state. As a mechanistic study, an experiment workflow was conducted to probe the impact of ions' concentrations in SW, either with or without sodium dodecylbenzene sulfonate (SDBS) which is an anionic surfactant. At first, contact angle (CA) measurement was carried out to evaluate the degree of wettability reversal upon treating the oil-aged calcite slabs with...