Sharif Digital Repository

In high-voltage applications, due to the use of high-ratio step-up transformers, the value of parasitic capacitance of these transformers is large compared to the low-voltage transformers. Moreover In these applications it is prefered to use single-capacitor filters instead of filters with inductors. In this paper a simple electrical model for two-winding high frequency transformer considering all of the parasitic elements is presented. This model is used in a full-bridge based dc-dc converter with capacitive output filter controlled by phase-shifted method. The operation of this converter in DCM is analysed and its analytical relations in different time intervals is derived and confirmed by... 

Boost converter operating in critical conduction mode is widely used in low-power power factor corrector because of its simplicity and low switching losses. The switching loss due to parasitic capacitor discharge at the on-time instant can also be reduced by a valley switching technique. In this paper, we introduce a new driver topology for the high-side switch in a synchronous boost converter operating in the critical conduction mode to obtain full zero-voltage switching. Using the proposed high-side driver topology, the conventional control circuit is sufficient to control the low-side switch, and no additional control circuit is required to adjust the timing of the switches. Finally, the... 

A Bandgap circuit capable of generating a reference voltage of less than 1 V with high PSRR and low temperature sensitivity is proposed. High PSRR achieved by means of an improved current mode regulator which isolates the bandgap voltage from the variations and the noise of the power supply. A vigorous analytical approach is presented to provide a universal design guideline. The analysis unveils the sensitivity of the circuit characteristic to device parameters. The proposed circuit is fabricated in a 0.18μm CMOS technology and operates down to a supply voltage of 1.2 V. The circuit yields 20 ppm/°C of temperature coefficient in typical case and 50 ppm/°C of temperature coefficient in worst... 

Developing efficient and appropriate modeling and control techniques for DC-DC converters is of major importance in power electronics area and has attracted much attention from automatic control theory. Since DC-DC converters have a complex hybrid nature, recently several techniques based on hybrid modeling and control have been introduced. These techniques have shown better results as compared with conventional averaging-based schemes with limited modeling and control abilities. But the current works in this field have not considered all possible dynamics of the converters in both continuous and discontinuous current modes (CCM, DCM) of operations. These dynamics are results of controlled... 

In this study, the effects of pulse current mode on corrosion resistance and mechanical properties of anodized coatings were explored. Thickness and hardness measurements, polarization and electrochemical impedance spectroscopy were employed to take mechanical and corrosion behaviors of the anodized coatings into consideration. Also, field-emission scanning electron microscopy (FE-SEM) was utilized to characterize the surface morphology of the coatings. It was shown that in short anodizing times, coating thickness is controlled by the heat concentrated on coating. Although at prolonged anodizing times, the coating thickness is affected by average current density. Hardness measurements showed... 

Several attempts have been made to design suitable controllers for DC-DC converters. However, these designs suffer from model inaccuracy or their inability to desirably function in both continuous and discontinuous current modes. This paper presents a novel switching scheme based on hybrid modeling to control a buck converter using mixed logical dynamical (MLD) methodologies. The proposed method is capable of globally controlling the converter in both continuous and discontinuous current modes of operation by considering all constraints in the physical plant such as maximum inductor current and capacitor voltage limits. Different loads and input voltage disturbances are simulated in MATLAB... 

This paper introduces "switched-resistor" circuits as a new family of current-mode sampled-data circuits with improved accuracy and linearity. Advantages of the switched-resistor circuits for high-speed and low-voltage applications are demonstrated. A switched-resistor biquad band-pass filter with a quality factor of 10 and clock frequency of 100 MHz, fabricated in a 0.18 μ m CMOS process, is also presented. The filter consumes 9 mW from 1.8 V supply. © 2008 Elsevier GmbH. All rights reserved  

A new low voltage bandgap reference (BGR) in CMOS technology, with high power supply rejection ratio (PSRR) is presented. The proposed circuit uses a regulated current mode structure and some feedback loops to reach a low voltage, low power and high PSRR voltage reference. The circuit was designed and simulated in 0.18um CMOS technology, with a power supply of 1.4 volt. The results show PSRR is 65dB at 1MHz and the output voltage variation versus temperature (-40 to 140) is less than 0.1%. This circuit shows robustness against process variation. ©2008 IEEE  

A compact low power circuit for implementation of a direct conversion OQPSK modulator is proposed. The circuit consists of a digital to analog converter, a low pass filter and an up-converter mixer. By embedding these three blocks, the circuit performance is enhanced and the total power consumption is reduced. The mixer is designed base on a Gilbert cell with on chip inductor loads. Instead of transconductance transistors of Gilbert cell, a fully deferential current mode DAC is used and proficiently a low pass filter is embedded between them and therefore the linearity of total system is improved. All of circuits are designed based on 0.18 μm CMOS technology with a single 1.8 volt power... 

this paper presents a new class AB circuit for current-mode signal processing. The proposed circuit provides high-dynamic range, low distortion and accurate definition of quiescent current and it is well suited for high-speed applications. A third-order low-pass filter with a cutoff frequency of 200MHz and 51dB dynamic range is also presented. The Alter consumes 2.7mW from 1.8V supply. © 2007 IEEE  

This paper presents a new class AB circuit for current-mode signal processing. These current mirrors are especially designed for advanced CMOS technologies and low-voltage high-speed applications. As an example two current amplifiers with a gain of 2, settling time of less than 6ns and current consumption of 500μA are designed and simulated. ©2006 IEEE  

A low voltage current mode sample and hold (S/H) in 0.18μm technology with 1.5v supply voltage is presented. This S/H has 12-bit linearity, i.e., gain and nonlinearity errors of S/H are less than 0.02μA for 100uA input current. Maximum sampling rate for this structure is 100 MHz (using double sampling technique). © 2005 IEEE