Sharif Digital Repository

In this study, the properties of poly (vinyl alcohol)(PVA) films incorporated with Zataria multiflora essential oil (ZMO) as a potential antioxidant/antibacterial material was investigated. PVA films were prepared from PVA solutions (2% w/v) containing different concentrations of ZMO. Water solubility, moisture absorption, water swelling, and water vapor permeability for pure PVA films were 57 ± 1.1, 99 ± 3.2%, 337 ± 8%, and 0.453 ± 0.015 g mm/m2 h, respectively. Incorporation of ZMO into PVA films caused a significant decrease in water swelling and moisture absorption and increase in solubility and water vapor permeability. Tensile strength, elastic modulus, and elongation at break for pure... 

Nano-biocomposites are a new class of hybrid materials composed of nano-sized filler (nanofiller) incorporated into a bio-based matrix. Such an association between eco-friendly biopolymers and nano-objects, with the aim to obtain synergic effects, is one of the most innovating routes to enhance the properties of these bio-matrices. In recent years, there has been an increasing interest in Starch as an inexpensive and renewable source has been used as a filler for environmentally friendly plastics for about two decades. However, the poor mechanical properties of starch based biopolymers, leads to use of nanoparticles as reinforcing materials. In the present study, the influence of a... 

The effects of melt quality and the placement of a filter in the filling system on Weibull distributions of tensile strength and elongation of Al-7%Si-Mg alloy castings were investigated. Three different combinations of melt quality and filtering were used: (a) unstirred, with filter in the filling system, (b) stirred to produce and entrain surface oxide films with no filter in the filling system to emulate poor initial melt preparation and melt handling, and (c) stirred and with a filter placed in the filling system. The results showed that the highest elongation and tensile strength values were obtained from the unstirred, filtered condition and lowest values were from stirred and... 

This work was carried out to investigate the effect of different Ti concentrations as a modifying agent on the microstructure and tensile properties of an in-situ Al-15 pctMg2Si composite. Cast, modified, homogenized small ingots were extruded at 753 K (480°C) at the extrusion ratio of 18:1 and ram speed of 1 mm/s. Various techniques including metallography, tensile testing, scanning electron microscopy were used to characterize the mechanical behavior, microstructural observations, fracture mechanisms of this composite. The results showed that 0.5 pctTi addition and homogenizing treatment were highly effective in modifying Mg2Si particles. The results also exhibited that the addition of Ti... 

Ultrahigh-molecular-weight polyethylene (UHMWPE)/fumed silica nanocomposites were prepared via in situ polymerization using a bi-supported Ziegler-Natta catalytic system. Nanocomposites with different nanoparticle weight fractions were produced in order to investigate the effect of fumed silica on thermal and mechanical properties of UHMWPE/fumed silica nanocomposites. The viscosity average molecular weight (M) of all samples including pure UHMWPE as the reference sample and nanocomposites were measured. Scanning electron microscope (SEM) images showed the homogenous dispersion of nanoparticles throughout the UHMWPE matrix while no nanoparticle cluster has been formed. Crystallization... 

The oxygen-barrier properties of poly(lactic acid) (PLA)/poly(vinyl acetate-co-vinyl alcohol) [P(VAc-co-VA)] were investigated. P(VAc-co-VA)s with vinyl alcohol (VA) contents of 5, 10, and 15 mol % were prepared with the acid-catalyzed hydrolysis of poly(vinyl acetate). The obtained copolymers with various contents of VA were blended with PLA at 5/95, 10/90, and 15/85 compositions. Films of the blends were prepared by a solution-casting method with chloroform as the cosolvent. Although the blend with 5% VA in the copolymer appeared to be miscible, the blends with 10 and 15% VA content in the copolymer were immiscible, as verified by dynamic mechanical analysis. The oxygen-barrier properties... 

In this study, a near equiatomic NiTi shape memory alloy was hot rolled at 800°C using thethickness reductions of 30 and 50%. Optical and transmission electron microscopy, together withX-ray diffraction were used to demonstrate the microstructural changes associated with the hotrolling at different thickness reductions. Repeated transformation cycling was employed toinvestigate the evolution of R phase during cycling. Microstructural observations revealed thepresence of deformation twins embedded in an elongated grain matrix in the hot rolled material.Moreover, it was found that with increasing degree of thickness reduction, the size and number ofdeformation twins increased throughout the... 

A cyclic forward-backward extrusion (CFBE) process was used as a severe plastic deformation (SPD) technique to produce ultrafine-grained aluminum rods. Yield strength and tensile strength of the specimens increased by increasing the number of CFBE cycles, while elongation to break decreased due to an increase in the grain refinement and microhardness. According to transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD) results, the average grain size was reduced from 120 μm to 315 nm after only 3 cycles of CFBE  

Hot deformation behavior of Al6063 alloy produced by direct powder extrusion was studied by means of uniaxial compression test in the temperature range between 300 and 450°C and strain rate range between 0.01 and 1s -1. Electron backscatter diffraction (EBSD) technique and transmission electron microscopy (TEM) were utilized to study the microstructure of the material before and after the hot deformation. The microstructure of the extruded alloy consisted of elongated grains within a subgrain structure and small grains free of low angle grain boundaries (LAGBs). An equiaxed duplex microstructure consisting of large substructured grains and fine grains separated by high angle grain boundaries... 

This paper presents the effect of martensite volume fraction (VM) on mechanical properties of AISI 4340 steel with ferrite-bainite-martensite microstructures. The steel bars were austenitized at 900°C for 1h followed by intercritical annealing at 740°C for 100min and quenching into a salt bath with temperature of 300°C and holding at different times to obtain triple phase (TP) microstructures with 34vol.% fraction ferrite and various martensite (or bainite) contents. Presence of three phases in adjacent to each other was confirmed by metallographic analysis and TEM studies. TEM observation also indicates higher density of dislocations within ferrite near martensite colonies compared to that... 

Reinforcement of styrene-butadiene-rubber (SBR) was investigated using two different carbon blacks (CBs) with similar particle sizes, including highly structured CB and conventional CB, as well as multi-walled carbon nanotube (MWCNT) prepared by mechanical mixing. The attempts were made to examine reinforcing mechanism of these two different classes of carbon nanoparticles. Scanning electron microscopy and electrical conductivity measurement were used to investigate morphology. Tensile, cyclic tensile and stress relaxation analyses were performed. A modified Halpin-Tsai model based on the concept of an equivalent composite particle, consisting of rubber bound, occluded rubber and... 

Al6063 powder was subjected to severe plastic deformation via high-energy mechanical milling to prepare ultrafine-grained (UFG) aluminium alloy. Uniaxial compression test at various temperatures between 300 and 450 °C and strain rates between 0.01 and 1 s-1 was carried out to evaluate hot workability of the material. Microstructural studies were performed by EBSD and TEM. The average activation energy and strain rate sensitivity of the hot deformation process were determined to be 280 kJ mol-1 and 0.05, respectively. The deformation temperature and applied strain rate significantly affected the grain structure of UFG Al alloy. A finer grain structure was obtained at lower temperatures and... 

The aim of this research is bonding of three-layered St/AZ31/St composite by roll-bonding process. The roll-bonding process was performed at three preheating temperatures, 340, 400 and 450°C, with thickness reduction of 30 to 68% and different thicknesses of intermediate layer (AZ31). In order to improve the bonding strength, the as-rolled specimens were annealed at constant temperature of 375°C. For evaluation of bond strength and investigating the formation of a diffusion layer, the results of peel test and microscopic images were studied. Tensile specimens were prepared along the rolling direction to measure the mechanical properties of the composite. The results showed that by increasing... 

Ethylene vinyl acetate/graphene oxide (EVA/GO) nanocomposite films were prepared via solution casting method. The morphological studies investigated using SEM and XRD methods and the results confirmed the formation of likely exfoliation structures and good interaction between matrix and fillers. The results of permeability measurements showed that films have good resistance against oxygen. Mechanical measurements revealed that Young’s modulus and tensile strength of EVA have improved with introducing GO because of proper dispersion of GO into matrix and good interaction between them; however, elongation at break decreased due to formation of strong and rigid polymer/filler network preventing... 

Thermo mechanical processing and controlled rolling of microalloyed steel sheets are affected by several factors. In this investigation, finishing temperature of rolling which is considered as the most effective parameters on the final mechanical properties of hot rolled products has been studied. For this purpose, three different finishing temperatures of 950, 900 and 850 °C below the non-recrystallization temperature and one temperature of 800 °C in the intercritical range were chosen. It is observed that decreasing the finishing temperature causes increase of strength and decrease of total elongation. This is accompanied by more grain refinement of microstructure and the morphology was... 

Dual-phase (DP) steels with different martensite contents were produced by subjecting a low carbon steel to various heat treatment cycles. In order to investigate the effect of dynamic strain aging (DSA) on mechanical properties, tensile specimens were deformed 3% at 300 °C. Room temperature tensile tests of specimens which deformed at 300 °C showed that both yield and ultimate tensile strengths increased, while total elongation decreased. The fatigue limit increased after pre-strain in the DSA temperature range. The effects of martensite volume fraction on mechanical properties were discussed  

4340 steel bars were austenitized at 850°C for 1 hour followed by heating at 700°C (ferrite and austenite region) for 90 min and quenching into a salt bath with different temperatures of 300, 350, 400 and 450°C. The steel bars were held for 1 hour at these temperatures before air cooling to room temperature. Various ferrite-bainite microstructures with 34% volume fraction of ferrite and different bainite morphologies were obtained. The results of SEM studies showed that by increasing the austempering temperature, the morphology of bainite varies from lower to upper bainite. According to the T-T-T diagram of the studied steel, the bainite transformation will not complete for the holding time... 

Stepwise-graded composite layer of M2 tool stel and 17-4PH stainless steel was fabricated by a simple powder layering technique and the isothermal and nonisothermal sintering response of the bilayer were examined. It was shown that the materials exhibit poor compatibility during co-sintering, i.e., the amount of mismatch shrinkage is significant. An improved compatibility was obtained by adding 0.2 wt% B to the stainless steel powder. Formation of relatively dense layer at the bonding zone indicated an enhanced densification rate at the interface. Microstructural studies showed formation of a ferritic interface in M2/17-4PH composite and elongated grains with an intergranular boride phase...