Sharif Digital Repository

A superhydrophobic polystyrene hollow fiber was electrospun around a copper spring collector. This approach led to the construction of a hollow fiber membrane, and the copper spring acted as a scaffold. The characteristic properties of the hollow fiber were studied by scanning electron microscopy. The membrane was used as a probe to transfer the extracting solvent from aquatic media to a gas chromatograph. After performing the liquid–liquid microextraction procedure on 10 mL of water sample by octanol, the whole solution was passed through the prepared polystyrene hollow fiber. Propanol, containing 2 mg/L lindane as the internal standard, was used for desorption and an aliquot of 2 μL of the... 

In this paper, the conventional 2D H-filter is modified to 3D multi-layer structures fabricated by low-cost xurography. The extraction efficiency was studied experimentally for different 3D structures and then compared with conventional 2D H-filter. Numerical simulations were performed to model the diffusion flow in the proposed H-filters, showing a good agreement with the experimental observations. Results show that 3D H-filters have higher extraction efficiency at the same Reynolds number. Moreover, these structures could benefit low-cost and commercial applications due to their higher efficiency at smaller sizes. © 2022, The Author(s), under exclusive licence to Springer-Verlag GmbH... 

In this research, organic solvent composed of hexane and methanol was used for lipid extraction from dry and wet biomass of Chlorella vulgaris. The results indicated that lipid and fatty acid extraction yield was decreased by increasing the moisture content of biomass. However, the maximum extraction efficiency was attained by applying equivolume mixture of hexane and methanol for both dry and wet biomass. Thermodynamic modeling was employed to estimate the effect of hexane/methanol ratio and moisture content on fatty acid extraction yield. Hansen solubility parameter was used in adjusting the interaction parameters of the model, which led to decrease the number of tuning parameters from 6... 

In this research, an attempt was made toward synthesizing a sol–gel–based silica aerogel and its subsequent coating on a copper wire by phase separation of polystyrene. Adaption of this new approach enabled us to coat the metallic wire with powder materials. The use of this method for coating, led to the formation of a porous and thick structure of silica aerogel. The coated wire was placed in a needle and used as the sorbent for in–tube solid phase microextraction of chlorobenzenes (CBs). The superhydrophobicity of sorbent on extraction efficiency was investigated by using different ratios of tetraethylorthosilicate/methyltrimethoxysilane. The surface coated with the prepared silica aerogel... 

In this study, cellulose acetate (CA) fibers were prepared using different solvent systems in electrospinning. The recorded scanning electron microscopy micrographs indicated that the morphology of the prepared fibers is closely associated with the type of electrospinning solvents. The prepared CA fibers were used as an extractive phase for on–line micro–solid phase extraction (μ-SPE) of nonsteroidal–inflammatory drugs (NSAIDs) in biological samples pursued by HPLC–UV determination. Work conducted on this research ascertained that the use of dichloromethane:acetone (3:1, v/v) solvent system in the CA dissolution for electrospinning, leads to the formation of porous ribbon–like fibers and... 

Polystyrene is one of the best candidates as the extracting medium due to its high stability in different media and acceptable extraction capability. However, the hydrophobic nature and low wettability of polystyrene limits its application to non–polar analytes. To resolve this limitation, in this project, amine groups were chemically attached to the surface of magnetic polystyrene. The resulting hydrophilic magnetic particles were expected to be capable of extracting both polar and non–polar analytes. Non–steroidal anti–inflammatory drugs (NSAIDs) were chosen for testing the applicability of modified magnetic polystyrene according to the importance of their analysis and also their wide... 

Sample preparation for non-target analysis is challenging due to the difficulty in the extraction of polar and non-polar analytes simultaneously. Most commercial solid sorbents lack the proper comprehensiveness for extraction of analytes with different physiochemical properties. A possible key is the combination of hydrophobic polymer and hydrophilic surface functional groups in solid based extraction methods in order to generate the susceptibility for retaining both polar and non-polar analytes. To pursue this goal, in this study, four polar groups including [sbnd]NH 2 , [sbnd]NO 2 , [sbnd]COOH, and [sbnd]COCH 3 were chemically bound to Amberlite XAD-4 substrate in order to prepare a... 

In this study, a method was described for the extraction of three antibiotic residues from cow milk samples using a graphene oxide–starch–based nanocomposite. The prepared nanocomposites were employed as an extractive phase for micro-solid phase extraction of antibiotics from cow milk samples. The extracted antibiotics, i.e. amoxicillin, ampicillin and cloxacillin, were subsequently analyzed by high-performance liquid chromatography–ultraviolet detection (HPLC–UV). Important variables associated with the extraction and desorption efficiency were optimized. High extraction efficiencies for the selected antibiotics were conveniently achieved using the starch–based nanocomposite as the... 

Molecularly imprinted polymer (MIP) was synthesized through the coprecipitation method on the graphene oxide anchored pencil lead as a substrate for the first time and applied as an efficient sorbent for pseudo stir bar sorptive extraction of nabumetone. The extracted analyte was determined by a novel spectrophotometric method based on the aggregation of silicate sol-gel stabilized silver nanoparticles in the presence of the analyte. The synthesized polymer was characterized using Fourier transform infrared spectroscopy and field emission scanning electron microscopy. Optimization of important parameters affecting the extraction efficiency was done using central composite design whereas the... 

To reduce the sulfur content of crude diesel, several sets of experiments have been conducted using electrochemical oxidative desulfurization technique using electrolyte of NaOH at different applied voltages. Due to impacts of operating parameters on desulfurization, kinetic study is pursued and it is found that the kinetic follows a second order reaction rate with a high accuracy. The reaction of desulfurization was modeled using COMSOL and followed by coupled electrochemical oxidation-extraction, while the extraction process was particularly performed using process simulator. The effects of different solvents on extraction performance were studied and dimethyl sulfoxide was selected for... 

To evaluate the selectivity and efficiency of solid phase microextraction (SPME) fiber coatings, synthesized by sol-gel technology, roles of precursors and coating polymers were extensively investigated. An on-line combination of capillary microextraction (CME) technique and high performance liquid chromatography (HPLC) was set up to perform the investigation. Ten different fiber coatings were synthesized in which five of them contained only the precursor and the rests were prepared using both the precursor and coating polymer. All the coatings were chemically bonded to the inner surface of copper tubes, intended to be used as the CME device and already functionalized by self-assembly... 

In the present work, the roles of inorganic oxide nanoparticles on the extraction efficiency of polyethylene terephthalate-based nanocomposites were extensively studied. Four fiber coatings based on polyethylene terephthalate nanocomposites containing different types of nanoparticles along with a pristine polyethylene terephthalate polymer were conveniently electrospun on stainless steel wires. The applicability of new fiber coatings were examined by headspace-solid phase microextraction of some environmentally important volatile organic compound such as benzene, toluene, ethylbenzene and xylene (BTEX), as model compounds, from aqueous samples. Subsequently, the extracted analytes were... 

A magnetic nanocomposite consisting of nanoparticles–polybutylene terephthalate (MNPs–PBT) was electrospun and used as an extracting medium for an on-line μ-solid phase extraction (μ–SPE)–high performance liquid chromatography (HPLC) set–up with an ultraviolet (UV) detection system. Due to the magnetic property of the prepared nanofibers, the whole extraction procedure was implemented under an external magnetic field to enhance the extraction efficiencies. The developed method along with the synthesized nanocomposite were found to be appropriate for the determination of trace levels of selected drugs including furosemide, naproxen, diclofenac and clobetasol propionate in the urine sample.... 

Direct extraction of molybdenum from sulfate solution with synergistic extractants (mixture of D2EHPA and TBP) was studied in the rotation column. The influence of extractant concentration and initial pH of aqueous phase was studied in the bench scale experiments. The outcomes demonstrated that the synergistic solvent extraction enhances the constancy of the extracted complexes for transfer into the organic phase. In the continuous experiments, the effect of different operating parameters such as speed of agitation, inlet solvent flow rate and inlet aqueous flow rate on the holdup, mean drop size, drop size distribution, slip and characteristic velocities and extraction percentage were... 

In salting-out liquid-liquid extraction (SALLE) technique, water-miscible organic solvents are used for extraction of polar analytes from saline solutions. In this study, for the first time, a coupled 1-mL syringes system was utilized to perform a miniaturized SALLE method. Sulfanilamide antibiotic was extracted and determined via the developed method followed by high performance liquid chromatography-ultraviolet detection (HPLC-UV). The extraction process was carried out by rapid shooting of acetonitrile as extraction solvent (syringe B) into saline aqueous sample solution (syringe A), and then the shooting was repeated several times at a rate of 1 cycle s-1. Thereby, an extremely large... 

A solution of polyamide (PA) containing polyethylene glycol (PEG) as a side low-molecular-weight polymer was electrospun. After synthesizing the PA-PEG nanofibers, the constituent was subsequently removed (modified PA) and confirmed by Fourier transform infrared spectroscopy. The scanning electron microscopy images showed an average diameter of 640 and 148 nm for PA and PA-PEG coatings, respectively, while the latter coating structure was more homogeneous and porous. The extraction efficiencies of PA, PA-PEG, and the modified PA fiber coatings were assayed by headspace solid-phase microextraction of a number of chlorophenols from real water samples followed by their determination by gas... 

A molecularly imprinted xerogel (MIX) for fentanyl was successfully prepared on the inner surface of a copper tube by sol-gel technology. Primarily, the tube was treated by self-assembly monolayers of 3-(mercaptopropyl) trimethoxysilane and then [3-(2,3-epoxypropoxy)-propyl]-trimethoxysilane was employed as a precursor for imprinting the template molecule in acidic conditions. During the sol-gel process influential parameters including volume and concentration of fentanyl were carefully investigated to obtain the most efficient and appropriate xerogel. In parallel, a non-imprinted xerogel (NIX) was synthesized in the absence of fentanyl. The extraction efficiencies achieved from MIX and NIX,... 

In the present work, a novel microextraction method named in situ solvent formation microextraction (ISFME) using ionic liquids (ILs) for preconcentration of carbaryl and carbofuran in water samples is introduced. In this method, a small amount of sodium hexafluorophosphate (NaPF6), as an ion pairing agent, was added to a sample solution containing a small quantity of 1-hexyl-3-methylimidazolium tetrafluoroborate [Hmim][BF4] as a hydrophobic ionic liquid. A cloudy solution formed as a result of formation of fine droplets of 1-hexyl-3-methylimidazolium hexafluorophosphate [Hmim][PF 6]. After centrifugation, the fine droplets of the extractant phase settled to the bottom of the conical-bottom... 

Molybdenum resources around the world are mainly associated with porphyry copper ores. Molybdenite (MoS2) is the main Mo mineral that has rhenium in its crystal lattice. This paper investigates the recovery of rhenium and molybdenum from a molybdenite concentrate using a hydrometallurgical treatment method. The molybdenite concentrate is leached with nitric acid and subjected to solvent extraction to recover and separate rhenium and molybdenum from the leached liquor. The effects of pH and the chemicals' concentration on extraction characteristics of Mo and Re are investigated to define the best condition for selective extraction of these metals. The tested leached liquor contained of 8.2... 

A new method based on the combination of magnetic solid phase extraction (MSPE) and spectrofluorimetric determination was developed for isolation and preconcentration of fluoxetine form aquatic and biological samples using sodium dodecyl sulfate (SDS) coated Fe 3O 4 nanoparticles (NPs) as a sorbent. The unique properties of Fe 3O 4 NPs including high surface area and strong magnetism were utilized effectively in the MSPE process. Effect of different parameters influencing the extraction efficiency of fluoxetine including the amount of Fe 3O 4 and SDS, pH value, sample volume, extraction time, desorption solvent and time were optimized. Under optimized condition, the method was successfully...