Sharif Digital Repository

Poly (vinylidene fluoride) (PVDF) nanocomposites were prepared via melt, solution, and co-precipitation mixing methods using Cloisite 30B as organoclay. The results from X-ray diffraction patterns display intercalation or exfoliation of nanoclay depending on the nanocomposite preparation method. The solvent cast and co-precipitated samples showed exfoliation, while intercalation was observed in the nanocomposites prepared by melt mixing. Introducing organoclay induced formation of β-crystals in the PVDF nanocomposites as evidenced by XRD and FT-IR. FT-IR analysis indicated that the samples prepared by the co-precipitation method had a higher tendency for β phase formation, while the sample... 

Soil deposits may experience different hydraulic states in terms of suction (φ) and saturation degree (Sr) while being subjected to large strain caused by dynamic loading during earthquakes. This phenomenon was investigated by considering the effects of initial φ, initial (Sr, sample preparation method, drainage condition, and cycle number (N) on dynamic properties. Shear modulus (G) and damping ratio (D) were specifically studied for unsaturated sand using a modified cyclic simple shear device for all zones of Soil Water Retention Curve (SWRC). Results revealed the relative significance of both φ and Sr in relation to SWRC on observed trends in G and D. Based on the analysis of some results... 

In this work, a comparative study has been performed on two ex-situ and one in-situ doping of titania photoanodes with reduced graphene oxide. The presence of finely dispersed reduced graphene oxide facilitates electron transport and reduces electron-hole recombination resulting in a better performance of doped titania photoanodes. It was found that in-situ doping, i.e. introduction of graphene oxide in solution together with titania precursor was the most performant case of graphene doping. This result was obvious by studying dye-sensitized solar cells based on such doped photoanodes but was also and mainly analytically demonstrated by subjecting the obtained materials to characterization... 

Multi-walled carbon nanotubes (MWCNTs) were immobilised with cobalt nanoparticles and analyzed by transmission electron microscopy. This modification procedure substantially improved colloidal dispersion of the immobilised MWCNTs in water and organic solvents, yielding uniform and stable thin films for modification of the glassy carbon electrode surface. The modified electrode showed an efficient catalytic role for the electrochemical oxidation of thioridazine (TR), leading to remarkable decrease in its oxidation overpotential of approximately 100 mV and enhancement of the kinetics of the electrode reaction, which can be confirmed by increasing in the peak current and sharpness of the peak.... 

Nowadays, gasochromic Pd/WO3 coatings as optically switchable materials have become more applicable for hydrogen sensors and smart windows. In this study, WO3 films were prepared by Pulsed Laser Deposition (PLD) and spin-coating sol-gel techniques. For deposition of Pd, first a layer of PdCl2 was obtained via a simple drop-drying process by dropping PdCl2 solution onto WO3 substrates and drying them at room temperature. Then Pd nanoparticles were synthesized via hydrogen gas exposure that causes reduction of the PdCl2 layer. According to Scanning Electron Microscope (SEM) observations before hydrogen reduction, many individual nanoparticles or fractal-like constructions of palladium were... 

A carbon paste electrode (CPE) modified with thionine immobilized on multi-walled carbon nanotube (MWCNT), was prepared for simultaneous determination of ascorbic acid (AA) and acetaminophen (AC) in the presence of isoniazid (INZ). The electrochemical response characteristics of the modified electrode toward AA, AC and INZ were investigated by cyclic and differential pulse voltammetry (CV and DPV). The results showed an efficient catalytic role for the electro-oxidation of AA and AC, leading to a remarkable peak resolution (∼303 mV) for two compounds. On the other hand, the presence of INZ, which is considered as important drug interference for AC, does not affect the voltammetric responses... 

Low cost dispersed supported cobalt oxide nanocatalysts on activated carbon (AC) were prepared by two different methods: (1) combined impregnation and deposition–precipitation (IMP-DP) and (2) heterogeneous deposition–precipitation (HDP). XRD, TEM, FESEM, BET and Boehm techniques were used for the characterization of the support and the catalysts. Characterization analyses indicated the negative effect of the wet impregnation method on the IMP-DP technique for the preparation of catalysts for the total oxidation of cyclohexane in air. The catalysts prepared by HDP and IMP-DP methods were found to have significant differences in oxidation activity, morphology, particle size, and shape of... 

Titanium dioxide is a cheap, chemically stable and non-toxic material. However its photocatalytic properties are unstable and it is a modest semiconductor and a mediocre insulator. For several applications it would be interesting to make it either more insulating or more conducting. The goal of this work was to modify the photocatalytic properties of nano-crystalline TiO2 powders by wet chemical routes and hydrothermal methods to understand the mechanism leading to these modifications The principal factors that influence the photocatalytic properties are on the one hand the concentration and nature of the chemical and physical conditions in TiO2, and on the other hand the morphology of the... 

Herein, we report a modified two-step method to construct a uniform and pinhole-free polycrystalline perovskite film with large grains up to the microscale using lead mixed-halide (PbI2-PbCl2) precursor solutions to guarantee the device functioning. Commonly used sequential deposition methods based on dip- and spin-coatings are combined with a vapor-assisted solution process to improve the perovskite morphology and tune the residual lead mixed-halides. These can enhance the optical absorption and efficiency of perovskite solar cell (PSC) devices. The impact of the Cl content in the lead mixed-halide precursors and the employed preparation methods on the photovoltaic performance of PSCs are...