Sharif Digital Repository

The main focus of this paper is to present thermodynamic and economic analyses and multi-objective optimization of a novel geothermal-solar multigeneration system. The system aims to produce hydrogen, freshwater, electricity, cooling load, and hot water and designed based on geothermal and solar energy. After modeling and thermodynamic and economic analysis, exergy destruction rate, exergy efficiency and, cost rate were calculated for each component of the system. The results showed that the highest amount of exergy destruction was related to parabolic trough collectors (PTCs) and absorption chillers. To select the geothermal fluid of the organic Rankine cycle (ORC), several different fluids... 

Photovoltaic (PV) panels provide a suitable way for the direct conversion of solar energy into electricity. The electrical output and efficiency of PV modules are dependent on working temperature. The present study contributes to investigate the efficiency of utilizing a flat plate closed-loop pulsating heat pipe (CLPHP) to cool down a PV panel in both thermal and economic aspects. Accordingly, a numerical investigation is employed to obtain the surface temperature and electrical gain of the PV panel through four scenarios, including natural cooling without additional equipment, CLPHP-based passive cooling, CLPHP-based active cooling, and a conventional flat plate cooling methods. The... 

Increasing energy demand has led to a substantial growth in the use of wind energy across the world, which can be attributed to the low initial and running costs and rapid and easy deployment of this technology. The development of hydrogen from wind energy is an excellent way to store the excess wind power produced, as the produced hydrogen can be used not only as clean fuel but also as input for various industries. Considering the good wind potentials of Yazd province, the variety of industries that are active in this area, and the central location of this province in Iran, which gives it ample access to major transport routes and other industrial hubs, hydrogen production from wind power... 

This paper describes the designing and evaluation of an alternative energy system which consists of PEMFC, PV, PEM electrolyser, methane reformer and hydrogen tank. In order to find out the minimum capacity of the components, a system sizing model is developed in MATLAB based on meteorological and electrical demand data. Three scenarios are considered based on different combinations of solar energy and fossil fuel energy as energy resources. The heating energy produced by the fuel cell is recovered for supplying domestic hot water while the system would supply electrical energy. Results show that system sizing strongly depends on scenarios and unit cost of electricity decreases through the... 

The plasmonic effects of infiltrated silver (Ag) nanoparticles, with different contents, inside a nanostructured TiO2 film on the photovoltaic performance of dye-sensitized solar cells (DSSCs) are explored. The synthesized Ag nanoparticles are immobilized onto deposited TiO2 nanoparticles by a new strategy using 3-mercaptopropionic acid (MPA), a bifunctional linker molecule. Transmission electron microscope (TEM) images show that monodispersed Ag and polydispersed TiO2 nanoparticles have an average diameter of 12 ± 3 nm and 5 ± 1 nm, respectively. Moreover, Fourier transform infrared spectroscopy (FTIR) analysis reveals that Ag nanoparticles were successfully functionalized and capped with... 

Herein, we demonstrate a facile low temperature chemical bath deposition approach to deposit a light scattering layer on a nanostructured mesoporous TiO2 bottom layer in a dye-sensitized solar cell architecture. Large TiO2 nanoparticles were formed on the top surface of photoanode electrodes via hydrolysis of TiCl4 at 70 °C. We controlled the size and agglomeration of these TiO2 nanoparticles by altering the concentration of TiCl4 in the chemical bath during the hydrolysis process. Electron microscope images revealed that mono-dispersed scattering particles having uneven surfaces with diameters between 100 to 300 nm formed on the mesoporous titania layer. The scattering behavior of the... 

This paper proposes a robust investment and operation model to attend the power and heat needs of a microgrid (MG) connected to the distribution system. The optimization algorithm decides on the best investment and operation of combined heat and power (CHP), boilers, PV power generation and battery energy storage systems (BESS). For the BESS, the algorithm estimates the optimal energy storage capacity (MWh) as well as the maximum hourly delivery capacity (MW). The non-linear and non-concave heat rate chart is recast by a mix-integer linear model to have a tractable and precise model. The model considers the uncertain in some parameters using probability density function (pdf) to portrait its... 

In this paper, special focus is paid to the long-term adoption of renewable electricity technologies and their implications for emissions reductions in Iran. MESSAGE, as a bottom-up energy supply optimization model, is used to assess the lowest-cost technology options. The potential impacts of transitioning to a renewable electricity supply are quantified, and the investment requirement to achieve a low-carbon generation mix is estimated. Alternative scenarios are defined to evaluate the impact of fossil fuel prices, the carbon tax and government incentives on the utilization of renewable resources, national renewable targets, and emissions reductions. The prioritization of non-hydro... 

Solar Chimney (SC) can play a significant role in energy consumption reduction of ventilation applications. The primary purpose of this study is to ameliorate the performance of an inclined rooftop SC integrated with the Phase Change Material (PCM) and Photovoltaic (PV) module, called the SC-PCM-PV system. To this aim, the effects of using finned absorbers and composite PCMs on the performance of the SC-PCM-PV system are investigated for the first time. A 3D-CFD model is developed via the finite volume method to examine the impact of various design parameters, including fin number, fin thickness, PCM type, and PCM mass on natural ventilation duration, ventilation capacity, and power output.... 

A comparative study has been made of hybrid solar cells based on poly(3-hexylthiophene) (P3HT) and different nano-structures of TiO2. Electrospinning, which is a low cost production method for large area nanofibrous films, was employed to fabricate TiO2 nanofibers and spin coating method was employed to fabricate organic-inorganic hybrid solar cells based on P3HT and TiO2 nanostructures. The performance of the hybrid solar cells was analyzed for four density levels of the TiO2 nanostructure. It was found that higher densities of TiO2 leads to more interface area and generates excitons, so that the power conversion efficiency increases to... 

Isolated microgrids depend mainly on diesel generation and have polluting transportation. This is being addressed by the introduction of renewable energy resources and electric vehicles (EVs). Hence, this paper presents a novel long-term planning model for the introduction of EVs in isolated microgrids. This work studies the replacement of internal combustion vehicles with electric ones by analyzing their respective investment, maintenance and operation costs. Various case studies are discussed, considering different EV and solar photovoltaic (PV) penetration levels, and varying prices of diesel in the planning horizon. Results demonstrate that investing in EVs could significantly reduce net... 

In this study, quick route-coating is practiced to substitute methyl ammonium (MA) cation with formamidinium (FA) at different ratios. Through optimizing the MA:FA ratio, a maximum power conversion efficiency (PCE) of 8.31% is achieved for holes transporting material-free MA0.8FA0.2PbI3 mixed PSCs with the JSC of 19.02 mA/cm2, VOC of 0.859 V and FF of 50.88%. Then, to improve the performance, stability and carrier transport dynamic, various additives (PVA, PVP, PEG and EC) are incorporated into the perovskite layer. The treatment of perovskites with additives has proved to cause significant changes in the surface roughness, charge accumulation, charge transport, charge transport resistance,... 

This study attempts to investigate a new way for cooling PV cell using natural vapor as coolant. The performance of solar cell was examined on simulated sunlight. The natural vapor encountered backside of PV cell vertically in various distribution and different mass flow rates. Also, the effect of natural vapor temperature in cooling performance was analyzed. Results indicated that the temperature of PV cell drops significantly with increasing natural vapor mass flow rate. In detail, the PV cell temperature decreased about 7 to 16°C when flow rate reaches 1.6 to 5grmin-1. It causes increasing electrical efficiency about 12.12% to 22.9%. The best performance of PV cell can be achieved at high... 

In this research, the design of a solar reverse osmosis desalination plant was investigated by integrating various components using TRNSYS and ROSA software. To this goal, a two-stage reverse osmosis system with 50% recovery in the city of Chabahar was modeled. The calculations were performed in three different case studies, i.e., a photovoltaic power plant, a solar collector power plant with Organic Rankine Cycles, and a photovoltaic thermal power plant with Organic Rankine Cycles, with the reverse osmosis desalination plant being a novel investigation. Water production and electrical energy generation of each case study were evaluated both on a daily and yearly bases. The simulation... 

This paper addresses a low complexity and high efficient cooling system applicable on photovoltaic (PV) system leading to enhance electrical efficiency and provide preheated water. The developed system consists of a photovoltaic panel, a cooling water system establishing a uniform surface temperature, and a solar water heater. According to the proposed system characteristics, the setup is constructed based on a single mono-crystalline solar panel to absorb more solar radiation intensity and generate more electrical energy per area in compare to a poly-crystalline panel. The preheated water produced by absorbed heat from the photovoltaic is conducted to a solar water heater to satisfy... 

This paper addresses a low complexity and high efficient cooling system applicable on photovoltaic (PV) system leading to enhance electrical efficiency and provide preheated water. The developed system consists of a photovoltaic panel, a cooling water system establishing a uniform surface temperature, and a solar water heater. According to the proposed system characteristics, the setup is constructed based on a single mono-crystalline solar panel to absorb more solar radiation intensity and generate more electrical energy per area in compare to a poly-crystalline panel. The preheated water produced by absorbed heat from the photovoltaic is conducted to a solar water heater to satisfy... 

In this work, the combination of H2O2 and an active visible-light-driven photocatalyst (Ag-S/PEG/TiO2) was utilized under natural solar radiation for the degradation of 2-nitrophenol (2-NP), and interaction effects between the photocatalyst and hydrogen peroxide were analyzed. For this purpose, experiments were designed using the response surface methodology based on the central composite design. The resulting data was utilized to obtain a model for the prediction of response (the degradation efficiency) as a function of two independent factors (H2O2 concentration and the photocatalyst loading). The statistical analysis indicated that optimum values of each of the two independent factors... 

Different structures of TiO2 photoelectrodes were fabricated with various arrangement modes of the layers. TiO2 nanoparticles were synthesized by a combination of sol–gel and solvothermal methods and were employed as the active layer of solar cells. Hierarchical TiO2 spheres (HTS) and spherical TiO2 particles (STP) were also prepared by hydrothermal and sol–gel processes, respectively, and used as the scattering layer of solar cells. Field emission scanning electron microscope and X-ray diffraction analyses revealed that all synthesized morphologies showed anatase structure with particle size around 20, 200–400 nm and 1.5–2.0 µm for the... 

Variability and uncertainty of wind and photovoltaic (PV) generations greatly influence technical and financial aspects of power systems. This paper examines the potential impacts of large-scale wind and PV farms on reliability level of composite generation and transmission systems. At first, reliability models of renewable-based units are developed. In these models, both component failure rates and uncertainty nature of renewable resources are taken into account. Using the proposed technique, the multi-state analytical models of a wind farm placed in Manjil and a PV farm placed in Jask both in Iran are extracted. Then, reliability studies of high renewable-energies penetrated power system... 

Variability and uncertainty of wind and photovoltaic (PV) generations greatly influence technical and financial aspects of power systems. This paper examines the potential impacts of large-scale wind and PV farms on reliability level of composite generation and transmission systems. At first, reliability models of renewable-based units are developed. In these models, both component failure rates and uncertainty nature of renewable resources are taken into account. Using the proposed technique, the multi-state analytical models of a wind farm placed in Manjil and a PV farm placed in Jask both in Iran are extracted. Then, reliability studies of high renewable-energies penetrated power system...