Sharif Digital Repository

In this research, we investigate the effects of various microstructural features on the behavior of spherical steel sheets, using the crystal plasticity finite element method. The cementite phase ratio, the grain sizes of ferrite and cementite, and the percentage of residual pearlite in the steel structure due to incomplete annealing are the major microstructural parameters studied in this work. A grain generator software has been developed to generate hexagonal ferrite grains as well as circular cementite particles distributed in the ferrite matrix. We use a hard coating with special properties as an intermediate layer around the cementite grains to simulate the contact between ferrite... 

This study investigates the effect of cold rolling prior to inter-critical annealing on microstructure and mechanical properties of ferrite-martensite dual phase steel. Samples were heated to 850 °C for 1 h followed by oil quenching, then the steel sheet were cold rolled by 0%,10%,15% and 20% reduction in thickness. The inter-critical annealing treatment (750 °C, 120min) was performed to generate a ferrite-martensite microstructure. Microstructural studies showed that increasing the applied cold rolling, leading to increase in volume fraction of martensite and decrease in ferrite grain size. Mechanical properties of dual phase steel were measured by tensile, impact and hardness tests.... 

The main purpose of the present research is to investigate the shunting phenomenon in a three-sheet RSW joint usingfinite element simulation. To this end, a three-sheet resistance spot weldingjoint was simulatedas an electrical-thermal-mechanical couplingproblem.Tovalidate the presentedsimulation, the finite element results were compared with the experimental results, including nugget size and geometric shapein theresistance spot weldingjoint.Afterwards, the multi-spot welds of three-sheet low carbon steels with the same thicknesses were analyzed considering the sequential distance of 45 mm. Various techniques, includingnewspot-welddiametermeasurement, electrical current density, electrical... 

In order to increase the cross-tension to the tensile-shear peak load ratio, aluminum clad steel sheet produced by roll bonding, was used for resistance spot welding to Al-Mg aluminum alloy. The results showed that the weld nugget formed between the aluminum clad layer and Al-Mg base sheet was the load bearing area. Presence of the metallurgical bond between the steel sheet and the aluminum clad layer led to the formation of the Al/Fe intermetallic compound with the thickness less than ∼3.5 μm. This narrow intermetallic layer did not play a detrimental role in the weld strength and therefore, the cross-tension to the tensile-shear peak load ratio reached up to ∼0.5 at the maximum... 

Tailored welded blanks (TWBs) technology can give the important possibilities to obtain components in the automobile industry. Friction stir welding (FSW) is a joining approach, which can adhere parts well with desired properties in weld zone. In this article, the main aim is investigation the effect of weld zone orientation on forming limit diagram (FLD) of the TWBs using experimental and finite element model. Three TWBs are produced FSW with three different orientations of weld zones including 00, 450 and 900 against major stress direction. The microstructure of the weld zones is divided and then observed via metallography procedures. Tensile tests are carried out to determine the... 

The application of electropulsing treatment (EPT) is studied on the microstructure and hardness of cold-rolled low carbon steel. The effects of electrical pulses on the grain refinement, precipitate size evolution and hardness are investigated. It is found that applying electrical pulse decreases the grain and precipitate size and increases the hardness in the early stages of electropulsing, but the grain and precipitate size is increased and the hardness is decreased by continuing electropulsing. Also, the effect of electropulsing treatment variables as well as treated time and number of periods are discussed. It is demonstrated that increasing treated time can accelerate achieving maximum... 

Al-Mg aluminum alloy was lap joined to aluminum clad steel sheet using pulsed gas tungsten arc welding process and Al-Si filler metal. The effects of the welding heat-input were investigated on the joint microstructure and mechanical properties. Weld metal microstructure, formation of intermetallic compounds (IMCs) at the joint interface and the fracture locations were studied using stereo, optical and scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS). The joint strength of the welds was evaluated by shear-tensile test. The results showed that presence of a thin aluminum clad layer with 350 μm thickness drastically decreased the Al-Fe intermetallic... 

Joining of Al-5083 alloy sheet to St-12 steel sheet was performed using a new friction stir spot welding (FSSW) technique in which the tool pin tip did not enter lower steel sheet. Effect of dwell time on the microstructure and mechanical properties of the joints was studied by various methods including microhardness measurements, shear test, stereo and light microscopy as well as scanning and transmission electron microscopy (SEM and TEM). Results indicated that compared to the conventional FSSW process, stronger joints can be achieved by this FSSW technique. Cross-sectional observation of the failed specimens indicated the occurrence of final fracture from the circumference of the tool pin... 

In this study six Cold-Formed Steel shear wall (CFS) with one and two side steel sheeting are tested under reversed cyclic loading. Besides, thirteen numerical models are simulated, using nonlinear finite element method, and analyzed under monotonic pushover loading. The studied parameters are the comparison of one and two side steel sheeting, the nominal thickness of steel sheet and boundary elements, and height to width aspect ratios of the wall. The performance of tested specimens is investigated in terms of lateral load-story drift response, failure modes and ultimate strength of shear walls. Based on AISI S213 the available strength of two-sided steel-sheathed walls is cumulative but... 

We studied the microstructure and mechanical characteristics of spot welded specimens, fabricated from low carbon steel sheets with different microstructures. Both ultra-fine grained (UFG) steel sheet and coarse grained (CG) steel sheet were used. The refined microstructure of the UFG steel has been produced by severe plastic deformation (SPD) using the constrained groove pressing (CGP) method. The grain size of the base metals was approximately 260. nm and 30. μm in diameter, respectively, in the UFG and CG steels. Examining the microstructure of a cross section cut through the spot weld reveals a similar grain size and phase distribution in the nugget on both the sides of the initial... 

Constrained groove pressing as a severe plastic deformation method is utilized to produce ultra-fine grained low carbon steel sheets. The ultra-fine grained sheets are joined via resistance spot welding process and the characteristics of spot welds are investigated. Resistance spot welding process is optimized for welding of the sheets with different severe deformations and their results are compared with those of as-received samples. The effects of failure mode and expulsion on the performance of ultra-fine grained sheet spot welds have been investigated in the present paper and the welding current and time of resistance spot welding process according to these subjects are optimized.... 

In this work, the feasibility of friction stir lap welding an aluminium alloy (Al-5083) to the aluminium clad steel sheet was studied. The welded joints were characterised by various methods including shear-tensile test and optical microscopy and scanning electron microscopy. The results indicated that sound and defect free joints were obtained. The fracture loads of the samples reached up to 94% compared with that of the steel base metal. Moreover, the joint strength linearly increased with the decrease in thickness of the aluminium layer roll bonded on the steel sheet. It was also shown that welding rotation and travel speed variation did not considerably impact the fracture loads in the... 

The influence of sheet thickness on sheet metal forming limits is a controversial issue; while some investigations indicate the considerable influence of thickness on forming limit diagrams (FLDs), others suggest that it is of negligible importance. In the present work, it has been demonstrated that if the thickness-reduction process is chosen so as not to alter the micro structure of the material, the forming limits do not change with variations of thickness. A material which has extensive usage in sheet metal forming processes of automotive industry (St14) has been provided. The initial thickness of the sheet is 1.5mm and using grinding process (which does not alter the microstructure) the... 

The newly developed multiphase transformation-induced plasticity (TRIP) steels are of interest for industrial applications because of their excellent combination of high strength and ductility. Their performance can be successfully controlled by designing an optimum balance in the volume fractions of ferrite, bainite and retained austenite. The characteristics of the retained austenite are considered to be the main key to achieving the desired final properties. Against this background, the effects of retained austenite characteristics, such as volume fraction, carbon concentration, size and shape, on the behaviour of TRIP steels have been studied. The crystallographic orientation of the... 

The welding of nanostructured low carbon steel sheets produced by severe plastic deformation (SPD) has been considered in the present paper. Constrained groove pressing (CGP) method is used for imposing the severe plastic deformation to the steel sheets as a large pre-strain. The SPDed sheets are joined using resistance spot welding (RSW) process. The results show that severe plastic deformation can effectively increase the electrical resistivity of steel sheets; therefore it can affect the microstructure and mechanical properties of spot welds. Microstructure and mechanical properties of fusion zone, heat affected zone (HAZ), recrystallized zone and base metal of SPDed sheets are... 

Tearing energies of annealed Al-steel bilayer sheets are investigated through multiple and single tensile tests. Total tearing energy of two layers determined separately by single tensile test is equal to tearing energy of bilayer sheet. It means that the bond between two layers has no effect on tearing energy  

However, there are many works on annealing process of SPDed non-ferrous metals, there are limit works on annealing process of SPDed low carbon steel. Therefore, in this study the annealing responses after constrained groove pressing (CGP) of low carbon steel sheets have been investigated. The sheets are subjected to severe plastic deformation at room temperature by CGP method up to three passes. Nano-structured low carbon steel sheets produced by severe plastic deformation are annealed at temperature range of 100-600 °C for 20. min. The changes of their microstructures after deformation and annealing are studied by optical microscopy. The effects of large strain and annealing temperature on... 

Thermomechnical processing and controlled rolling of microalloyed steel sheets are affected by several factors according to the final properties of product. To create the high mechanical properties, a uniform and fine-grain structure is necessary in hot rolled final products. To produce such microstructures, every stage of the thermomechanical processing of the steel rolling has to be carefully controlled. Hence, first step is grain coarsening control that it usually occurs during reheating for slab. For this purpose, seven different reheating temperatures between 1000 to 1300 °C with 50 °C increments were chosen in this investigation for soaking treatment. By soaking the specimens in... 

There are many works on annealing process of SPDed bulk metals but there are limited works on annealing process of SPDed sheets. Therefore, in this study the annealing response after constrained groove pressing (CGP) of low carbon steel sheets has been investigated. These sheets are subjected to severe plastic deformation at room temperature by CGP method up to three passes. Nano-structured low carbon steel sheets produced by severe plastic deformation are annealed at temperature range of 100 to 600 °C for 20 min. The microstructural changes after deformation and annealing are studied by optical microscopy. The effects of CGP strain and annealing temperature on microstructure, strength and... 

In this study the effect of stress field on delamination and fiber/ matrix debonding in laminated composite panels is investigated from the micro-mechanical point of view by means of 3-D Finite Element Models. Specifically, the behavior of two-layer cross-ply symmetric laminates made up of SCS-6/Ti-24Al-11Nb Intermetallic Matrix Composite (IMC) during cooling from the processing temperature is studied. The results show that large plastic strains occur at the fiber/ matrix interface at the fiber end on the laminate free edge which may eventually extend to the interface of the layers of the laminate inflicting delamination damage. This phenomenon is more serious at the corner areas of the...