Sharif Digital Repository

In this article, both experimental and numerical approaches are conducted to present a constitutive equation for 5052 aluminum diaphragms under quasi-static strain rate loadings. For this purpose the stress-strain curves at different strain rates are obtained using tensile tests. Brittle behavior during tensile tests is observed due to samples thin thicknesses. Employing Johnson-Cook constitutive equation no yields in reasonable agreement with these tensile tests results. Therefore, developing a more suitable constitutive equation for aluminum diaphragms is taken into consideration. This equation is then implemented into the commercial finite element software, ABAQUS, via a developed user... 

The hot working behavior of a low carbon resulfurized free-cutting steel was studied by hot compression tests at temperature range of 1000-1200°C with strain rates of 0.001 to 1s-1. The conventional parameters such as activation energy of deformation and relationships between flow stress/strain and Zener-Hollomon parameter were determined. Both the critical stress and strain for initiation of dynamic recrystallization (DRX) were determined using: (1) strain hardening rate versus stress curve, (2) the natural logarithm of strain hardening rate versus strain curve, and (3) the constitutive equations. In summary, for low carbon resulfurized free - cutting steels, the activation energy of... 

Post-uniform deformation energy of materials is defined as absorbed energy per unit area after necking. The energy is constant for a material type and its experienced specific processing history and also depends on its mechanical parameters as workhardening exponent, strain rate sensitivity, post-necking extension and inhomogeneity factor. Different methods such as single and multiple tensile testing had been proposed in the literature to calculate tearing energy, but the effect of post-necking extension had not been expressed explicitly. A new model by implementing uniform and failure elongations with the combination of Unwin theory is introduced. Based on the model, it was shown that... 

The hot deformation characteristics of 7075 aluminum alloy (AA7075) are investigated by means of hot compression tests carried out in the temperature range of 200-450 C and strain rate range of 0.0003-1 s-1. Two novel processing maps based on flow localization parameter and enhanced DMM are developed and compared with conventional DMM results. It is observed that processing maps based on flow localization parameter can be used successfully to predict AA7075 thermomechanical behavior. Also, the comparison of the DMM results indicates that the new approach to calculate DMM power dissipation efficiency and instability criteria corresponds better with experimental observations. The occurrence of... 

Commercially pure aluminum sheets, AA 1050, are processed by accumulative roll bonding (ARB) up to eight cycles to achieve ultrafine-grained (UFG) aluminum as primary material for mechanical testing. Optical microscopy and electron backscattering diffraction analysis are used for microstructural analysis of the processed sheets. Strain rate sensitivity (m-value) of the specimens is measured over a wide range of strain rates by stress relaxation test under plane strain compression. It is shown that the flow stress activation volume is reduced by decrease of the grain size. This reduction which follows a linear relation for UFG specimens, is thought to enhance the required effective (or... 

This article presents the cyclic behavior of the A356.0 aluminum alloy under low-cycle fatigue (or isothermal) and thermo-mechanical fatigue loadings. Since the thermo-mechanical fatigue (TMF) test is time consuming and has high costs in comparison to low-cycle fatigue (LCF) tests, the purpose of this research is to use LCF test results to predict the TMF behavior of the material. A time-independent model, considering the combined nonlinear isotropic/kinematic hardening law, was used to predict the TMF behavior of the material. Material constants of this model were calibrated based on room-temperature and high-temperature low-cycle fatigue tests. The nonlinear isotropic/kinematic hardening... 

In this study, a set of constitutive equation corrected for deformation heating is proposed for a near equiatomic NiTi shape memory alloy using isothermal hot compression tests in temperature range of 700 to 1000 °C and strain rate of 0.001 to 1 s -1. In order to determine the temperature rise due to deformation heating, Abaqus simulation was employed and varied thermal properties were considered in the simulation. The results of hot compression tests showed that at low pre-set temperatures and high strain rates the flow curves exhibit a softening, while after correction of deformation heating the softening is vanished. Using the corrected flow curves, the power-law constitutive equation of... 

Employing a proper pulse shaper in the conventional split Hopkinson pressure bar (SHPB) test helps to achieve dynamic equilibrium condition and to fulfill a constant strain rate condition in the test specimen. To this end, the parameters affecting the incident pulse shape, i.e., pulse shaper thickness, pulse shaper diameter, striker bar length and striker bar velocity are experimentally studied. Moreover, simulation results, validated by experimental data together with wave propagation analysis, are exploited to provide general guidelines to properly design a pulse shaper. It is recommended to use a relatively large diameter pulse shaper for testing work-hardening materials. Also, for... 

The behavior of hot extruded Al-6Mg during hot deformation has been studied using hot compression test. The tests were performed at temperatures of 350, 450, and 550°C and strain rates of 0.001, 0.1, and 1s -1. Due to the effects of friction and adiabatic heating generated during compression, the attained true stress-true strain curves have been corrected. After correction of friction effect, the virtual work hardening has been removed from stress-strain curves. The flow stress increases and reaches a steady state after correction of adiabatic heating effect. Corrected curves and microstructural examinations exhibit the occurrence of dynamic recovery during hot compression of the alloy. The... 

In this paper, a constitutive model with a temperature and strain rate dependent flow stress (Bergstrom hardening rule) and modified Armstrong-Frederick kinematic evolution equation for elastoplastic hardening materials is introduced. Based on the multiplicative decomposition of the deformation gradient,new kinematic relations for the elastic and plastic left stretch tensors as well as the plastic deformation-dependent spin tensor are proposed. Also, a closed-form solution has been obtained for the elastic and plastic left stretch tensors for the simple shear problem.To evaluate model validity, results are compared with known experimental data for SUS 304 stainless steel, which shows a good... 

In this study, hot extrusion of AA6061-5% SiCp composite was studied to determine the composite thermo-mechanical behaviour during deformation and the mechanical properties of extruded composite. Hot compression tests were first carried out to obtain the flow stress behaviour of the composite at different temperatures and strain rates. Then a mathematical model was used to estimate the required energy as well as to predict temperature and strain distributions during the process. Finally, hot extrusion experiments were performed in order to verify the predictions and, also, tensile and hardness testing were conducted to evaluate mechanical properties of extruded material. Comparison between... 

A fine-grained aluminum-matrix hybrid nanocomposite reinforced with TiO2, MgO and Al3Ti nanoparticles was prepared via reactive friction stir processing (FSP) of an Al-Mg sheet with pre-placed TiO2 particles (50nm; 3.1vol%). The microstructure of the hybrid nanocomposite comprises high-angle grain boundaries (~90%) with an average size of 2μm and hard inclusions with sizes in the range of 30-50nm. Evaluation of the hot deformation behavior of the nanocomposite by uniaxial tensile testing at different temperatures (300-450°C) and strain rates (0.001-0.1s-1) shows that the deformation apparent activation energy of the nanocomposite is 137kJmol-1 at ≤300°C. The values of the activation energy... 

In this study, the plastic instabilities associated with the Portevin-Le Chatelier (PLC) and their effects on the mechanical properties and the fracture surfaces have been investigated for AA 5083. Tensile tests were performed at various temperatures and strain rates in order to do so. Then, serrated and smooth yielding domains were determined in Ln ε̇-1/T diagram. The stress-strain curves related to the serrated domain show the values of flow stress decreases by increasing the strain rate at a constant temperature. In addition, the plot of critical strain versus imposed strain rate indicates an inverse manner at very low strain rates. It is confirmed that the type of PLC bands alters the... 

A finite difference technique is developed to predict the second stage creep displacement rates and stress analysis of a short fiber metal matrix composite subjecting to a constant axial load through a micromechanical approach. The technique is capable to take into account the presence of interfacial debonding as one of the main factors affecting the creep performance of short fiber composites. The exponential law is adopted to describe the matrix creep behavior. Also, a model for prediction of interfacial debonding at fiber/matrix interface is developed using a stress based method. The obtained results could greatly help to better understand the flow pattern of matrix material and the load... 

Nickel-base superalloys such as René 80 are widely used in manufacturing aircraft turbine blades. They are usually coated in order to increase their wear, oxidation, erosion, and hot corrosion properties against environmental degradation. In this article, the mechanical behavior (tensile and low-cycle fatigue (LCF)) of uncoated and aluminide-coated (CODEP-B) René 80 has been studied at 871 °C and 982 °C. Experimental results show that the tensile properties of coated specimens are relatively lower than those of uncoated ones in the same conditions, but application of coating increases the LCF life of René 80 at T = 871 °C, 982 °C, R = (εmin/εmax) = 0, strain rate of 2 × 10-3 s-1, and Δεt =... 

The biomechanical behavior of brain tissue is needed for predicting the traumatic brain injury (TBI). Each year over 1.5 million people sustain a TBI in the United States. The appropriate coefficients for modeling the injury prediction can be evaluated using experimental data. In the present paper, using an experimental setup on bovine brain tissue, unconfined compression tests at quasi-static strain rates of ϵ 0.0004s-1, 0.008s-1 and 0.4s-1 combined with a stress relaxation test under unconfined uniaxial compression with ϵ 0.67s-1 ramp rate are performed. The fitted viscohyperelastic parameters were utilized by using obtained stressstrain curves. The finite element analysis (FEA) is... 

Purpose: The purpose of this paper is to investigate the thermomechanical behavior of stainless steel AISI 304L during rolling at elevated temperatures. Design/methodology/approach: Two-dimensional finite element analysis together with the upperbound solution were used for predicting temperature field and required power in warm and hot rolling operations. The required power and heat of deformation were estimated employing an upper-bound solution based on cylindrical velocity field and at the same time, temperature distributions within the rolling steel and the work rolls were determined by means of a thermal finite element analysis. To consider the effect of flow stress and its dependence on... 

The flow behaviour of Al–SiC nanocomposites prepared by mechanical milling and hot powder extrusion methods was studied at different temperatures (350–500°C) and strain rates (0.005–0.5 s−1). The flow of the Powder metallurgy nanocomposites exhibited a peak stress followed by a dynamic flow softening behaviour. It was shown that mechanical milling increased high-temperature strain rate sensitivity of ultrafine-grained (UFG) aluminium while decreasing its flow dependence to temperature. Constitutive analysis of the hot deformation process by Zener–Hollomon parameter (Z) also indicated a remarkable increase in the deformation activation energy (about 40%). Likewise, SiC nanoparticles (up to... 

An interaction between ferrite recrystallization and austenite transformation in low-carbon steel occurs when recrystallization is delayed until the intercritical temperature range by employing high heating rate. The kinetics of recrystallization and transformation is affected by high heating rate and such an interaction. In this study, different levels of strain are applied to low-carbon steel using a severe plastic deformation method. Then, ultra-rapid annealing is performed at different heating rates of 200–1100°C/s and peak temperatures of near critical temperature. Five regimes are proposed to investigate the effects of heating rate, strain, and temperature on the interaction between... 

In order to analyze the flow behavior and workability of Ni–42Cu in cast and wrought conditions, hot deformation tests were performed at temperatures and strain rates within the ranges of 900–1150 °C and 0.001–1 s−1, respectively. Tensile tests showed a “hot ductility trough” at 950 °C for both alloys. The drop in hot ductility was more considerable in the cast alloy because of the sluggish dynamic recrystallization. The hot ductility drop and grain boundary cracking, particularly in the cast alloy, were attributed to the segregation of detrimental atoms to the boundaries. It was shown that the hot ductility of the wrought alloy could be improved with increasing strain rate. It was...