Sharif Digital Repository

The proper understanding of rheological characteristics of CGA based fluids is of crucial importance in determining the performance of the fluid, in order to maintain the most effective fluid properties for safe, efficient, and economical drilling operation. This paper presents a concise investigation on the effect of concentration of the three main components of a novel environmentally friendly lightweight CGA based drilling fluid, i.e., xanthan gum biopolymer, starch, and biosurfactant, to the Herschel-Bulkley rheological model parameters. The three parameters of Herschel-Bulkley model, i.e., yield stress, fluid consistency, and fluid flow index were calculated by fitting the experimental... 

Aims: Our goal was the characterization of a new moderate thermophilic polycyclic aromatic hydrocarbon (PAH)-utilizing Nocardia strain. Methods and Results: A thermophilic bacterium, strain TSH1, was isolated from a contaminated soil. The macroscopic and microscopic features fit well with the description of Nocardia species. The results of 16S rRNA gene analysis showed 100% match to the type strain of N. otitidiscaviarum DSM 43242T. Strain TSH1 showed the same mycolic acid pattern as the type strain of N. otitidiscaviarum but its fatty acid profile did not permit identification to the species level. The carbon utilization profile of strain TSH1 was different from N. otitidiscaviarum. The... 

The feasibility of fabricating relatively monodispersed polymeric nanoparticles by the electrospray method in a modified electrospray set-up is demonstrated in this study. The polymer solution is electrosprayed in the single cone-jet regime through a nozzle. After solvent evaporation, during which particles pave from the nozzle to collector, the fabricated nanoparticles can be collected in deionized water, which plays the role of surfactant for particles, not allowing them to aggregate. The results of scanning electron microscope and dynamic light scattering analysis clearly confirm the fabrication of monodispersed spherical polymeric nanoparticles with diameter range from 80 to 120nm with... 

Alumina nanofluids are one of the most useful nanofluids. In order to evaluate the colloidal behavior of nanoparticles in alumina/water nanofluid, the influence of effective factors such as pH, ionic strength and surfactants, was studied. Zeta potential, particle size and turbidity change of each nanofluid was investigated. According to the results for 0.05, 0.1 and 0.2 mass% nanofluid, point of zero charge was obtained at pH values of 9.5, 10.2 and 10.5, respectively. The highest nanofluid stability occurred at pH 4 and its lowest was at pH 10. The anionic surfactant had a greater effect on the stability in compared with cationic and nonionic surfactants. By increasing in ionic strength,... 

Alumina nanofluids are one of the most useful nanofluids. In order to evaluate the colloidal behavior of nanoparticles in alumina/water nanofluid, the influence of effective factors such as pH, ionic strength and surfactants, was studied. Zeta potential, particle size and turbidity change of each nanofluid was investigated. According to the results for 0.05, 0.1 and 0.2 mass% nanofluid, point of zero charge was obtained at pH values of 9.5, 10.2 and 10.5, respectively. The highest nanofluid stability occurred at pH 4 and its lowest was at pH 10. The anionic surfactant had a greater effect on the stability in compared with cationic and nonionic surfactants. By increasing in ionic strength,... 

In the present study, the effect of two different kinds of surfactants namely conventional (Sodium dodecyl benzene sulfonate (SDBS)) and ionic liquid (IL)-based surfactants are investigated on the tertiary oil recovery using relative permeability concept. In this way, besides the Amott wettability index measurement, unsteady state core flooding tests are performed to not only find the effect of surfactant injection on tertiary oil recovery, but also to investigate their effects on relative permeability of carbonate rocks. In addition, for more reliable conclusions regarding the possible mechanisms, interfacial tension (IFT), compatibility and emulsification tests are carried out as a... 

Demands for hydrocarbon production have been increasing in recent decades. As a tertiary production processes, chemical flooding is one of the effective technologies to increase oil recovery of hydrocarbon reservoirs. Retention of surfactants is one of the key parameters affecting the performance and economy of a chemical flooding process. The main parameters contribute to surfactant retention are mineralogy of rock, surfactant structure, pH, salinity, acidity of the oil, microemulsion viscosity, co-solvent concentration, and mobility. Despite various theoretical studies carried out so far, a comprehensive and reliable predictive model for surfactant retention is still found lacking. In this... 

The aim of this study is to simulate the self-assembly of the surfactant molecules with special chemical structure and bending stiffiness into bilayer membranes using a mesoscopic Dissipative Particle Dynamics (DPD) method. The surfactants are modeled with special chemical structure and bending stiffiness. To confirm that the novel model is physical, we determine the interaction parameters based on matching the compressibility and solubility of the DPD system with real physics of the uid. To match the mutual solubility for binary uids, we use the relation between DPD parameters and x-parameters in Flory-Huggins-type models. Unsaturated bonds can change the stiffiness of a lipid membrane,... 

In this study, ZnO nanoparticles with 3 to 4 nm size and spherical shape have been prepared. For the first time, TEA (triethanolamine) as a surfactant has been used for the preparation of ZnO nanoparticles. The best concentration of each component was adjusted through comparison between different sol absorption spectra. The best sol regarding its optical property was subjected to analysis by photoluminescence spectroscopy. TEM micrograph and electron diffraction pattern of these particles were obtained to represent the morphology and crystalline phase of the particles, respectively. Experimental results have shown that the prepared zinc oxide nanoparticles by this method have higher... 

In this work, simultaneous inferential control of particle size distribution (PSD) and molecular weight distribution (MWD) in a semi-batch emulsion polymerization reactor of styrene has been addressed. Using a comprehensive dynamic model for PSD and MWD predictions and performing a sensitivity analysis, it has been revealed that free surfactant and chain transfer agent (CTA) concentrations in the reactor are the most suitable candidates for inferential control of PSD and MWD, respectively. To control concentrations of these species in the reactor, their inlet feed flow rates are used as manipulated variables. It is assumed that the concentration of CTA is measured infrequently and therefore... 

Inkjet printing of colloidal metals is an attractive method for direct patterning of electrically conductive structures and interconnects in electronic devices, owing to low-cost, low-waste and simplicity of the process. In the present work, mixtures of well-dispersed silver nanoparticles and ethylene glycol were prepared for the inkjet printing process. Three different surfactants including PVP, MSA and AOT were added to study the stability of the nanosilver colloids. The effect of high-intensity ultrasonic treatment and temperature on the rheological properties was investigated utilising a rheometer in plate-plate geometry. It is shown that the viscosity of the ink increases with... 

A photochemical approach on the size control of CdS nanoparticles is presented. CdS nanoparticles were grown using the photo-induced reaction of sodium thiosulfate with Cadmium sulfate, in the absence of any surfactant. Particles of 5.5-11 nm were obtained by changing the illumination time. The dark growth of nanoparticles was negligible, however we found by optical scattering measurements that a ripening phenomenon occurs and the size of nanoparticles slightly increases with time. © 2005 Elsevier B.V. All rights reserved  

Colloidal Gas Aphron (CGA) are finding increasing application in fields of science and engineering because of their distinctive characteristic. As interest in the application of CGA based fluids grows and in order to select the best procedure for using them in successful petroleum engineering operations, there is a need to gain a better understanding of the factors that affect their properties and behavior. This article discusses the rheological characterization, stability analysis and filtration properties of CGA based fluids for three bio-polymers and two ionic surfactant. The stability and filtration analysis were investigated with the static drain rate technique and API filtration tests,... 

This study concerns micro-scale analysis of filtration loss control induced by blockage ability of a new colloidal gas fluid, Colloidal Gas Aphron Nano-Fluid (CGANF) in fractured porous media. Fumed silica nanoparticles and a novel environmentally friendly bio surfactant, Olea Europaea, were used for monitoring CGANF displacements in heterogeneous micromodels including single fracture. Analysis of pressure drop along the micromodel during tests showed an increasing resistance to flow of CGANF dispersion through porous media as more CGANF was injected. When lamella division occurs, more small bubbles are formed and then pressure drop through porous media increases. Small bubbles play an... 

In the present study, an aqueous root-extract of Acanthophyllum laxiusculum (AREAL) was evaluated for phenanthrene removal from two samples of contaminated soil. AREAL showed a linear solubilization enhancement for phenanthrene with a weight solubilization ratio of 0.05. Batch soil washing experiments caused the removal of phenanthrene with efficiencies of 96.7% and 78% from soils with 0.78% and 2.73% organic carbon, respectively. Desorption kinetics of phenanthrene exhibited a twophase pattern, namely, a rapid release as the initial phase and a slower removal as a subsequent phase. A two-compartment exponential model could adequately represent the two phases of the kinetic pattern of... 

A composite film constructed of surfactant doped over-oxidized polypyrrole and multi-walled carbon nanotube was prepared on the surface of glassy carbon electrode by the electro-polymerization method. Surface characterization of the modified electrode was performed by scanning electron microscopy, cyclic voltammetry and electrochemical impedance spectrometry. The investigations have been proved that the over-oxidation of the modifier film resulted in a porous thin layer that improves the interlayer diffusion mechanism for the electroactive species. On the other hand, the negative charge density on the surface of the electrode excludes the negative analytes (e.g. ascorbate and Fe(CN)63?/4?)... 

Here in, for the first time, we report a new and simple procedure for preparing reduced graphene oxide/nickel-cobalt double layered hydroxide composite on the nickel foam (Ni-Co LDH/rGO/NF) via a fast and simple two-step electrochemical method including potentiostatic routes in the presence of CTAB as a cationic surfactant. Graphene oxide coated nickel foam prepared by simple immersion method. After that, the prepared electrode reduced electrochemically to obtain rGO/NF electrode. Finally, the rGO/NF electrode was used as cathode for electrodeposition of Ni-Co LDH in the presence of CTAB as cationic surfactant. The prepared electrodes were characterized by field emission scanning electron... 

The present study reports a simple electrochemical approach to the fabrication of a new nanocomposite containing PtPd nanoflowers (NFs) promoted with two-dimensional (2D) nanosheets (NSs) structure cuprous oxide (Cu2O) supported on reduced graphene oxide (rGO) (PtPd-NFs/Cu2O-NSs/rGO). Scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectra, Raman spectroscopy, and energy dispersive X-ray spectroscopy are used for characterization of the PtPd-NPs/Cu2O-NPs/rGO. SEM images showed that vertical-standing arrays of Cu2O with an edge length up to 1 μm and thickness of about 20 nm are electrodeposited on the surface of rGO film. Also, PtPd needle-like NFs with visible and... 

Here in, for the first time, we report a new and simple procedure for preparing reduced graphene oxide/nickel-cobalt double layered hydroxide composite on the nickel foam (Ni-Co LDH/rGO/NF) via a fast and simple two-step electrochemical method including potentiostatic routes in the presence of CTAB as a cationic surfactant. Graphene oxide coated nickel foam prepared by simple immersion method. After that, the prepared electrode reduced electrochemically to obtain rGO/NF electrode. Finally, the rGO/NF electrode was used as cathode for electrodeposition of Ni-Co LDH in the presence of CTAB as cationic surfactant. The prepared electrodes were characterized by field emission scanning electron...