Sharif Digital Repository

This paper introduces a new concept that we call smart transmission expansion planning (TEP) based on unconventional high surge impedance Loading (HSIL) line designs that will revolutionize power delivery. To date, these two areas (TEP and transmission line design) have been conducted separately. For TEP, planners use the electrical parameters of a few standard conventional line designs to study planning scenarios, and then, the final candidate line is constructed. In such a sequence, cost-effective scenarios often do not meet the technical criteria of load flow. This paper will demonstrate that this sequence can be overturned; namely, a transmission expansion planner can get optimal line... 

The application of digital technologies in power systems has resulted in an evolutionary replacement of electromechanical devices with numerical ones featuring internal digital processors with communication capabilities. A substation automation system (SAS) deploys substation operation functions, including control, protection, monitoring, and measuring. Ethernet technology and local area networks (LANs) make it possible to design substation communication architectures with greater reliability, availability, speed, and cost savings than conventional hard-wired systems. This paper proposes a new method to describe topologies of the SAS as an interconnected network. The concept of data... 

Tension leg platforms (TLPs) are well-known structures for oil exploitation in deep water. One of the current issues in compliant structures in the sea is variation in frequency and structural response due to a nonlinear parameter in the equation of motion. Variation of frequency is important in fatigue life study of tethers. A perturbation method is used in contrast to the traditional methods. This method does not require a small parameter for finding surge motion of TLP. In this paper, homotopy perturbation method (HPM) is used to solve a highly nonlinear differential equation of surge motion. Calculated responses by HPM are compared with those obtained from both linear and nonlinear... 

Here, using the probabilistic evaluation based on the Monte Carlo method, back-flashover rate and shielding failure flashover rate of 230 kV overhead transmission lines in the western regions of Iran are evaluated. To such an aim, first, the number of thunderstorm days per year is collected from the reported weather information in order to determine the ground flash density. Then, using MRU-200 equipment, the tower-footing resistance of several towers is measured. Matlab® software is used in order to produce lightning surges considering its probabilistic nature and randomly distribution on the ground to evaluate striking distance based on the geometric model. Then, calculated parameters are... 

In order to restrain ferroresonance in coupling capacitor voltage transformers (CCVT), two kinds of ferroresonance suppression circuits (FSCs) , are proposed in this paper: the resonant type, the fastsaturation reactor type which are connected to secondary side of CCVTs. Frequency domain analyses, for voltage ratio magnitude, are carried out for CCVTs to obtain preferable FSC. Furthermore, using surge suppressors such as metal oxide varistors (MOV) to improve the performance of the FSCs is investigated. Time domain simulations demonstrate that ferroresonance can be cleared in few cycles in presence of FSCs. The Electromagnetic Transients Program (EMTP) is used for modeling and fine-tuning... 

This research focused on making novel low-voltage SnO2 varistors by CuO addition on conventional high-voltage SnO2 varistors. Moreover, the withstand surge capability of samples was studied. The results showed that CuO addition enhances grain growth of SnO2 and coarse-grained SnO2 varistors with simple microstructures were acquired in 1 mol% CuO-doped sample. This coarse-grained SnO2 varistor presented a high nonlinear coefficient (23) and low leakage current density (23 µA/cm2) with low breakdown field value of 0.6 kV/cm. Despite the large grain size, the low residual voltage ratio (2.3) was obtained for this sample compared to the CuO-free sample. The decrease in grain electric resistivity... 

Substation Automation Systems (SAS) offer powerful, fast, and viable ways to design, automate, and implement substation protection, control, and monitoring functions in modern transmission and distribution grids. Today's SAS -more than ever- rely on the adoption of IEC61850 as a worldwide standard for interoperability and dependable peer-to-peer and substation communications. Being based on the Ethernet computer networking technology, the reliability issues associated with latency in 61850-enabled SAS is of a design consideration. Unpredictability is the most important challenge for latency assessment. This paper discusses the background framework for latency evaluations in SAS by... 

This study presents the results of failure analysis of a 28 MW gas turbine at the Rei electrical power plant. The gas turbine failed during the shutdown period and near its second natural frequency at 4200 rpm. Initial inspections revealed that the compressor disk of stage 15 was fractured, and all of the stationary and rotary blades of stages 14-18 of the compressor had been detached or broken from the dovetail region of the disks. The fracture roots were investigated by performing finite element modeling and fractography analysis. It was shown that a crack was initiated from the disk edge on its interface with the rotor shaft and was propagated under cyclic loading. As a result of the... 

Vulnerability of power electronic converters in DC microgrids in case of fault occurrence in DC cables necessitates using a fast fault detection and isolation scheme. In this paper, a modified, fast and selective protection scheme has been presented, which provides the required tripping of low voltage DC (LVDC) microgrids. This protection scheme has been developed based on the natural characteristics of the fault current, in which the first and second derivatives of the fault current have been employed to define thresholds for discriminating between faulted and non-faulted situations. To enhance fault detection capability of the protection scheme, definition of thresholds have been improved... 

Previous experiments on the fouling/current and fouling/wave interactions were mostly limited to two dimensional (2D) net panels or isolated twines. The current paper deals with the wave-induced forces/moments in three dimensional (3D) physical models of a gravity net-cage. The colonial hydroid Ectopleura larynx, a common fouling organism in the aquaculture industry, was artificially modelled and considered in the current experiments. A clean cage and cages with different fouling lengths were tested under deep-water regular wave trains. The time series of the wave-induced forces/moments in the surge, sway, roll and pitch degrees of freedom were recorded and analysed. The experimental results... 

The present paper studies the impact of dynamic interaction between high-voltage substation equipment on the response and vulnerability of substation equipment. The 3D numerical model is developed for four types of vulnerable equipment in the both unconnected and connected conditions. The bus slider-rigid bus assembly is utilized to establish the connection between the equipment. The incremental dynamic analysis is carried out in the developed systems to produce the fragility function for each equipment. Also, the Monte Carlo approach is employed to evaluate the accuracy of the generated functions. It is concluded that the incorporation of connection parts in the model can significantly... 

Design of centrifugal compressors can be accomplished using methods provided in text books and open literature. In this general approach, after determination of dimensions in meridional plane, blade profiles are designed using aerodynamic methods. Then, some blades are trimmed at the beginning to avoid inlet blockage. But there is no clear guidance on how this trimming must be performed. With this widely implemented method, splitter blades have the same profile as main ones. In this research, blade profiles and dimensions of the compressor impeller are not changed while the effect of changes in the position and angle of splitters leading edge are investigated. An optimization scheme is... 

Clamp mode resistor capacitor diode (CMRCD) snubbers have a simple and easy implementing structure. They have been widely adopted in the pulsed power supplies to provide a safe operating condition for the series insulated gate bipolar transistors (IGBTs). The main problem of the CMRCD snubbers is their poor performance in the voltage balancing of the series IGBTs. They are essentially overvoltage protectors and clamp the voltage of the IGBTs in a probable potentially dangerous condition. This issue diminishes the expected lifetime of the series IGBTs, where a number of them face a higher level of the voltage than that of the others. The unbalanced voltage of the series IGBTs will result in a... 

The limited value of the insolated-gate bipolar transistors (IGBTs) blocking voltage is an important issue for applying these devices to the high-voltage power converters. An effective solution is to use a series configuration of these devices in order to achieve higher voltage ratings in addition to save the interesting features such as fast rising time. To reach this goal, acceptable equal voltage sharing for the IGBTs are provided by the series stacking schemes in the normal operation.However, a considerable difference in their voltage level will be occurred in the short-circuit condition. Although the IGBT can withstand the short-circuit current in a defined time, the occurred high...