Loading...
Search for:
teymoori--parisa
0.059 seconds
A new low phase noise LC-tank CMOS cascode cross-coupled oscillator
, Article Proceedings - 2010 18th Iranian Conference on Electrical Engineering, ICEE 2010, 11 May 2010 through 13 May 2010 ; 2010 , Pages 397-402 ; 9781424467600 (ISBN) ; Fotowat Ahmady, A ; Nabavi, A ; Sharif University of Technology
2010
Abstract
In this paper we introduce a new low phase noise cascode Cross-coupled oscillator by use of the general topology of Cross-coupled oscillator and cascode amplifier. By simulation a comparison between the conventional Cross-coupled oscillator and the new cascode Cross-coupled oscillator is also presented, which shows that the latter improves the phase noise by 2dB under the same conditions. The figure of merit (FOM) of -186.4 dBc/Hz is achieved for the new oscillator by simulation
Network layer challenges of IEEE 802.11n wireless ad hoc networks
, Article Lecture Notes of the Institute for Computer Sciences, Social-Informatics and Telecommunications Engineering ; Volume 72 LNICST , 2012 , Pages 377-388 ; 18678211 (ISSN) ; 9783642291562 (ISBN) ; Yazdani, N ; EffatParvar, M ; Teymoori, P ; Movaghar, A ; Sharif University of Technology
2012
Abstract
Recent demands toward high-speed wireless networks are growing. IEEE 802.11n, as the latest standard toward achieving higher speeds, aims to enhance IEEE 802.11 for higher throughputs. There are few works which analyze performance of this protocol in single-hop networks in terms of MAC layer-based parameters. Most of these works suggest disabling the RTS/CTS handshake to reduce MAC layer overheads. However, the effects of this protocol on the upper layers, especially the network layer, are still unknown. This paper deals with investigating performance of the network layer over IEEE 802.11n. Through extensive simulations performed in NS-2 we show that although network throughput is improved...
Time Delay Estimation between Two Photoplethysmography Signals under Noisy Conditions
, M.Sc. Thesis Sharif University of Technology ; Zahedi, Edmond (Supervisor) ; Shamsollahi, Mohammad Bagher (Supervisor)
Abstract
In this project, a processing algorithm is approached which is resistant against environmental and motion noises to find the pulse transmission time using two photoplethysmography signals. For this purpose, a new processing framework is checked and generalized for photoplethysmography signals. Already, this processing framework had impressive results. The considered processing method is obtained by offering a dynamic model for the signal and using it in a Kalman filter structure. For the photoplethysmography signals, with modeling every beat of signal to a Gaussian three or four sum form and with adding self-returned equations for model parameters, a nonlinear signal model is obtained. Then,...
Experimental Study of Drying and Calcination of Simulated High-Level Waste (HLW)
, M.Sc. Thesis Sharif University of Technology ; Samadfam, Mohammad (Supervisor) ; Zahakifar, Fazel (Supervisor) ; Zaheri, Parisa (Co-Supervisor)
Abstract
One of the novel methods of stabilization of nuclear waste is the use of vitrification technology. In order to stabilize high level wastes (HLLW) in glass, it is required that the elements are in their oxide form. Therefore, it is necessary to evaporate the waste and turn it into a solid form so that the elements can be converted into oxide form in the calcination furnace. Hence, one of the challenges of stabilization is the optimization of evaporation and calcination conditions. In this research, the parameters affecting evaporation were first investigated. Using laboratory measurements of application: temperature (110 to 180 °C), presence of nitric acid (0.5 to 4 mol/L), ratio of zirconium...
Fabrication Patient-Specific Drill Guide Templates for Cervical Pedicle Screw Placement
, M.Sc. Thesis Sharif University of Technology ; Arjmand, Navid (Supervisor) ; Parnianpour, Mohammad (Supervisor) ; Azimi, Parisa (Co-Supervisor)
Abstract
One of the most common spinal surgeries involves spinal fusion or vertebral fixation, which is used to treat various conditions such as intervertebral disc disease, scoliosis (lateral deviation of the spinal column), fractures, infections, or the presence of tumors in the spinal column. In this surgical procedure, the use of pedicle screws and titanium rods prevents motion and friction between two vertebrae. Screws may enter the vertebrae in the wrong position and angle, causing bone weakening, rupture of nerve roots or blood vessels, weakness or lack of sensation in some parts of the body, spinal cord injury, and in severe cases, paralysis of the patient. For this reason, fusion surgery is...