Sharif Digital Repository

This paper presents a harmonic termination technique for single-and multi-band high-efficiency class-F monolithic microwave integrated circuit (MMIC) power amplifiers (PAs). The harmonic termination network (HTN), realized with the minimum possible number of elements, can be used to terminate an arbitrary number of harmonics in a single-band PA or harmonics of multiple frequencies in a concurrent multi-band PA. The drain and gate bias lines are embedded in the HTNs to obviate the need for RF chokes and reduce the chip area. A single-and a dual-band MMIC PA are designed using the proposed technique and implemented in a 0.25-μm AlGaAs-InGaAs pHEMT technology. The single-band 5.5-GHz PA... 

A technique for simultaneous cancellation of noise, second-order distortion and third-order distortion in CMOS LNAs is presented. The proposed LNA topology consists of a matching stage and two common-source amplifier stages, performing single-ended to differential signal conversion with balanced output. The second and third-order nonlinearity of the individual amplifiers as well as the distortion caused by the interaction between the stages are suppressed to achieve high IIP3. A method for intrinsic cancellation of the second-order interaction is employed to reduce the dependence of the IIP3 on the frequency spacing between the interfering signals in the two-tone test. © IEICE 2009  

In this paper, we present a thorough analysis based on photon-counting techniques on temporal/spatial fiber-optic code-division multiple-access systems incorporating both post- and pre-optical amplifiers. In this analysis, we consider the effect of shot noise, thermal noise, and source extinction on system bit-error rate. Our results can be used to estimate the maximum tolerable amount of quantum fluctuations in the received signal  

A PC-based digital lock-in amplifier was implemented completely in software (Labview) for photoplethysmograph (PPG) measurement. Experiments carried out to evaluate the performance of the amplifier show that the system can recover the signals up to 40 dB below the interference (ambient light). This system can be customized later to measure the trans-abdominal PPG signal of pregnant women for fetal heart rate detection. ©2007 IEEE  

This paper presents the design procedure of monolithic microwave integrated circuit (MMIC) high-power amplifiers (HPAs) as well as implementation of high-efficiency and compact-size HPAs in a 0.25-μm AlGaAs-InGaAs pHEMT technology. Presented design techniques used to extend bandwidth, improve efficiency, and reduce chip area of the HPAs are described in detail. The first HPA delivers 5 W of output power with 40% power-added efficiency (PAE) in the frequency band of 8.5-12.5 GHz, while providing 20 dB of small-signal gain. The second HPA delivers 8 W of output power with 35% PAE in the frequency band of 7.5-12 GHz, while maintaining a small-signal gain of 17.5 dB. The 8-W HPA chip area is 8.8... 

This paper presents a design methodology for class-J monolithic microwave integrated circuit (MMIC) power amplifiers (PAs). Theoretical derivations of optimum load impedances, output power, efficiency, and maximum bandwidth are described in presence of nonlinear drain-source resistance of transistors (RDS). A procedure is developed for ideal transistor sizing where transistors are concurrently stabilized and sized to achieve the maximum power-added efficiency (PAE). A 3.5-7 GHz, 0.5-W class-J PA is implemented in a 0.1-μm AlGaAs-InGaAs pHEMT technology to check the accuracy of the proposed approach. With chip dimensions of 1.57 × 1.29 mm2, the PA achieves 56% average PAE over the frequency... 

In this brief, a design technique for tapered distributed low-noise amplifiers (LNAs) is presented. A circuit model is developed for gain and noise analysis of a nonuniform distributed amplifier (DA). It is shown that by optimal tapering of gate and drain transmission lines and transistors, the tapered distributed LNA can provide lower broadband average noise figure (NF) compared to a uniform DA. A proof-of-concept integrated circuit is implemented using a 0.1-μm GaAs pHEMT process. The amplifier provides average gain of 15.2 dB and 3-dB bandwidth of 43.3 GHz. The average NF of 2.3 dB and minimum NF of 2.0 dB are achieved over 2–40 GHz. The chip consumes 55 mA current from a 2-V supply. IEEE... 

This paper presents a design procedure for a wideband 6-18-GHz monolithic microwave integrated circuit highpower amplifier (HPA) in 0.25-μm AlGaAs-InGaAs pHEMT technology. The design is mainly focused on the realization of the passive circuits to provide the required low-loss and wideband impedance transformation networks. The two-stage GaAs HPA achieves an average output power of 39.6 dBm and a peak output power of 40.5 dBm at 11 GHz, in pulsed mode operation, with a small-signal gain of S21 > 10 dB over the entire bandwidth. The average power added efficiency (PAE) is 22%, with a peak PAE of 29% at 11 GHz. The HPA chip occupies an area of 5×3.6 mm2. The achieved output power and the... 

This paper presents the design and implementation of a distributed class-J power amplifier (DJPA) in a 0.25-μm AlGaAs-InGaAs pHEMT technology. Class-J mode of operation is introduced in design of distributed power amplifiers (DPAs) to achieve high power added efficiencies (PAEs) over wide frequency ranges. Extensive load-pull (LP) and source-pull (SP) simulations are performed to show that class-J PAs are less sensitive to proper termination of higher order harmonics, and high PAE and output power can be obtained even if the second, third, fourth, and fifth harmonics comprise a real impedance. This is essential in DPAs as the higher order harmonics of the frequencies at lower side of the... 

In this brief, a design technique for tapered distributed low-noise amplifiers (LNAs) is presented. A circuit model is developed for gain and noise analysis of a nonuniform distributed amplifier (DA). It is shown that by optimal tapering of gate and drain transmission lines and transistors, the tapered distributed LNA can provide lower broadband average noise figure (NF) compared to a uniform DA. A proof-of-concept integrated circuit is implemented using a 0.1-μm GaAs pHEMT process. The amplifier provides average gain of 15.2 dB and 3-dB bandwidth of 43.3 GHz. The average NF of 2.3 dB and minimum NF of 2.0 dB are achieved over 2-40 GHz. The chip consumes 55 mA current from a 2-V supply. ©... 

In this paper, the switching behavior of the cascode topology is improved through the floating bulk (FB) technique. Although the cascode structure has the advantage of reducing voltage stress on transistors, its parasitic elements increase power loss. The FB technique has been proposed to alleviate the power loss in the cascode class-E PA topology which results in enhancement of power added efficiency (PAE). In this method, the bulk of the common-gate (CG) transistor is connected to the ground through a resistor. As a result, the parasitic capacitances between the drain and source of the CG transistor create a new path of current that accelerates charging of parasitic capacitance at the... 

Optical fiber doped with lead salts quantum dots (QDs) of different radii, has previously been proposed as a wide-band amplifier in the optical communication range. The emission and absorption spectra of QDs are size-dependent. Optical fiber amplifier doped with QDs of different sizes is an inhomogeneous gain medium. This inhomogeneity is the principle of operation of wide-band quantum-dot-doped fiber amplifiers (QDFAs). To study the effects of inhomogeneity such as spectral hole burning on the amplifier behavior, a fiber amplifier with an arbitrary size distribution of QDs is taken into consideration. The light propagation equations and rate equations for the inhomogeneous medium are... 

In this paper, two output matching networks (OMNs) are proposed for integrated class-J and class-J-1 mode power amplifiers (PAs). The first MN provides the required load impedances of the class-J mode (i.e., Z(f0) = Ropt + j Ropt and Z(2 f0) = -j (3π/8)Ropt), where as the second MN realizes the optimal impedances of class-J-1 PAs (i.e., Z(f0) = Ropt - j Ropt and Z(2 f0) = j (3π/8)Ropt ). Detailed theoretical analyses are presented for each MN, and the values of matching components (i.e., inductors and capacitors) are obtained in terms of Ropt. Analytical derivations are verified by simulation results, while bandwidth and loss performances of each MN are also characterized. Two... 

In this brief, the switching behavior of the cascode topology is improved through the floating bulk (FB) technique. Although the cascode structure has the advantage of reducing voltage stress on transistors, its parasitic elements increase power loss. The FB technique has been proposed to alleviate the power loss in the cascode class-E PA topology which results in enhancement of power added efficiency (PAE). In this method, the bulk of the common-gate (CG) transistor is connected to the ground through a resistor. As a result, the parasitic capacitances between the drain and source of the CG transistor create a new path of current that accelerates charging of parasitic capacitance at the... 

Feed-forward is one of the best methods for linearizing microwave power amplifiers, but due to device tolerance in implementation of the system components, the practical Inter-Modulation Rejection (IMR) value may differ quite much from the theoretical IMR value. One of the methods to improve the practical performance of the system is using the multi-loop configuration. Here we have introduced the multi-loop feedforward systems and we have estimated the practical IMR values of the system using Monte-Carlo analysis. As the analysis shows, although the number of components in a multi-loop system is increased with respect to a simple feed-forward system, but the difference between the practical... 

This paper presents an unilateralization technique for distributed amplifiers (DAs) based on the transformer coupling between the gate and drain lines. Theoretical analysis of the DA indicates that the voltage waves in the gate and drain lines can be described by a system of linear partial differential equations. The transformer coupling between the lines allows for cancellation of the reverse transmission coefficient of the system. There is an optimal value for the coupling coefficient between the lines that unilateralizes the DA. This optimal coupling coefficient is derived in terms of the gate-drain capacitance and capacitances of the gate and drain lines. Using the proposed technique,... 

This paper presents two wideband GaAs MMIC driver power amplifiers (PAs) suitable for X and Ku bands. The required number of stages and number of branches in each stage for an M-stage driver PA architecture is analyzed. Design of wideband matching networks for monolithic microwave integrated circuit (MMIC) driver PAs is explained and design parameters of a cascaded K-section T matching network (MN) are derived. Finally, measurement results of 8-13 GHz and 13-19 GHz driver PAs, both implemented on 0.25 μm pseudomorphic high electron mobility transistor (pHEMT) technology, are demonstrated. Each driver PA delivers 31 dBm output power with 30 % nominal PAE over the operating frequency. © 2017... 

This paper presents the theoretical introduction and experimental validation of the "Class-J2 Mode Power Amplifier," which provides higher efficiency and output power compared with conventional class-J mode counterpart. This mode of operation is realized by injection of the second-harmonic current to drain node of a class-J power amplifier (PA) to reduce the 45° phase shift between drain current and voltage signals. Similar to class-J PAs, the second-harmonic impedance of class-J2 PAs is purely reactive to simplify the design of the output matching network. The auxiliary second-harmonic injection circuit comprises a transistor biased in class-B mode followed by a class-C biased amplifier to... 

The internally coded time-hopping coherent ultra-short light pulse code division multiple access (CULP CDMA) scheme (recently introduced) with an optical amplifier is described and its performance in fibre-optic communication systems is analysed. In accordance with the important role of optical amplifiers in optical communication systems, a preamplifier at the input of the receiver is used in order to compensate the losses because of the spectral encoder, spectral decoder and optical fibre path. The authors evaluate the bit error rate of the system considering the effects of the multiple access interference, noise because of the optical amplifier and thermal noise using saddle point...