Sharif Digital Repository

A hot filament chemical vapor deposition (HFCVD) method was used to prepare Fe-Cr thin film on Si substrate. The produced layers were used as catalysts for growing carbon nanotubes (CNTs) from liquid petroleum gas (LPG) at 825 °C by thermal CVD (TCVD) method. To characterize the obtained catalysts or CNTs, X-ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and Raman spectroscopy were used. CNTs were grown on HFCVD derived Fe-Cr catalyst with the LPG as carbon source successfully. It was found that an annealing process on catalysts enhances the surface concentration of Cr atoms and reduces the sizes of catalyst particles. The... 

We report experimental evidence of Cu surface segregation in Ni/Cu system, during deposition of Ni film onto Cu substrate at room temperature and during heat treatment in vacuum. Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) by Tougaard's analysis results show that surface segregation defeats in competition with increase in Ni thickness and terminates when thickness of Ni increase to more than 4 nm. Surface energy and concentration were calculated using contact angle measurements and the results confirm that segregation reduces the surface energy. Surface segregation during heat treatment at 150-220 °C range as a function of time initially shows linear mass... 

Local annealing of amorphous NiTi thin films was performed by using an Nd:YAG 1064 nm wavelength pulsed laser beam. Raw samples produced by simultaneous sputter deposition from elemental Ni and Ti targets onto unheated Si (100) and Silica (111) substrates were used for annealing. Delicate treatment with 15.92 W/mm2 power density resulted in crystallization of small spots; while 16.52 and 17.51 W/mm2 power densities caused ablation of the amorphous layer. Optical microscopy, scanning electron microscopy, X-ray diffraction and atomic force microscopy were performed to characterize the microstructure and surface morphology of the amorphous/crystallized spot patterns  

To investigate boiling heat transfer characteristics of nanofluids, transient quenching experiments of a high temperature silver sphere in water-based nanofluids with Ag and TiO2 nanoparticles were performed. A silver sphere with a diameter of 10 mm and an initial temperature of 700 °C was quenched in these nanofluids at a temperature of 90 °C. The results showed a considerable reduction in the quenching ability of nanofluids compared to that of pure water. The presence of nanoparticles in water caused the film boiling mode to vanish at lower temperatures depending on the mixture concentration. Calculated heat transfer rates in nanofluids were lower than those in pure water. In the quenching... 

There are several types of drilling methods to increase the productivity of a well, such as horizontal drilling, extended reach horizontal drilling and Multilateral (ML) drilling. It is thought that ML wells could be more economic with higher productivities than horizontal or extended reach horizontal wells. Advances in ML drilling promise reduced costs, greater flexibility and increased profit potential. In the last 20 years, thousands of ML wells have been drilled worldwide, but only a small percentage of the total number of wells is multilateral. The probable reason may be lack of concise information and misconceptions surrounding the costs and perceived risks. However, recent advances in... 

During the last decade, fabrication of high-quality graphene films by chemical vapor deposition (CVD) for nanoelectronics and optoelectronic applications has attracted increasing attention. However, processing of large-area monolayer and defect-free graphene films is still challenging. In this work, we have studied the effect of processing conditions on the self-limited growth of graphene monolayers on copper foils during low pressure CVD both experimentally and theoretically based on thermokinetics and kinetics of Langmuir adsorption. The effect of copper pre-treatment, growth time, and carbon potential of the atmosphere (indicated by the methane-to-hydrogen gas ratio, r) on the quality of... 

The gas nanosensor of indium oxide nanowires in laser assisted approach, doped with tin and zinc for gas sensing and 1D growth purposes respectively, was reported. The nanowires were very sensitive to H2S gas in low concentration of 20 ppb gas at room temperature. The fast dynamic intensive and sensitive response to gas was in a few seconds with an on/off sensitivity ratio of around 10. The square cross-section indium oxide nanowires were fabricated through physical vapor deposition (PVD) mechanism and annealing approach. The field emission scanning electron microscopy (FESEM) observations indicated that the annealing temperature was vital in nanostructures' morphology. The fabricated... 

Vertical vibration of structures due to strong near-field earthquakes could culminate in catastrophic consequences. In this article, the optimum patterns of two types of wave barriers with different geometry configurations, buried in the soil domain, are obtained in order to reduce the vertical acceleration of the top of a circular foundation placed on the soil surface. In order to look into the influence of various soil deposits, six soil deposits with diverse material properties and bedrock depths are examined. The topology optimization procedure for finding the optimum position of the wave barriers has been conducted using coupled finite element-genetic algorithm methodology. First, the... 

Thin films of Fe73.1Cu1Nb3.1Si14.7B8.2 alloy with 200, 500, and 800 nm thicknesses have been deposited by RF sputtering. Their magnetic properties have been characterized using Alternating Gradient Field Magnetometer (AGFM) and Vibrating Sample Magnetometer (VSM). The effects of residual stresses investigated by nanoindentation experiments were conducted on the as-deposited samples. It is observed that the coercivity of as-deposited films is inversely proportional to the thickness in relation with the residual stress induced during sputtering. © 2017 Sharif University of Technology. All rights reserved  

Developing low-cost, scalable and reproducible synthesis methods for water oxidation reaction (WOR) catalysts is highly desirable and also challenging in energy, environmental and industrial applications. In this context, electrochemical deposition is known as an easy and cost-effective technique in nanomaterial growth. Herein, cobalt-based nanoflakes were grown on a flexible and commercially available steel mesh substrate by electrodeposition approach with a crystalline structure as a mixture of oxide, hydroxide and oxyhydroxide phases. For the first time, the correlation between electrodeposition parameters, time and current density, and morphological characteristics of the grown... 

There is a global tendency towards using Distributed Generation (DG) and renewable energy resources. Considering low utilization cost and low undesirable environmental effects, wind farms have become a considerable resource for producing electrical energy in many countries. Since Wind farms are not programmable and their power output which depends on weather and wind speed is uncertain, they create problems for utilizing electricity system. There are different methods for preserving system stability against the uncertainty of wind power plants. Optimal utilization of pumped storage and gas resources is one of the approaches for reducing production risk of wind farms. In this paper, it is... 

The compatibility of atomic layer deposition directly onto the mixed halide perovskite formamidinium lead iodide:methylammonium lead bromide (CH(NH2)2, CH3NH3)Pb(I,Br)3 (FAPbI3:MAPbBr3) perovskite films is investigated by exposing the perovskite films to the full or partial atomic layer deposition processes for the electron selective layer candidates ZnO and SnOx. Exposing the samples to the heat, the vacuum, and even the counter reactant of H2O of the atomic layer deposition processes does not appear to alter the perovskite films in terms of crystallinity, but the choice of metal precursor is found to be critical. The Zn precursor Zn(C2H5)2 either by itself or in combination with H2O during... 

Study of the plastic deformation in polymeric honeycombs can pave the way for understanding the deformation localization in more complex cellular structures, which have received progressive attention in the past few years. This study compares the strain localization in deforming honeycombs made by two cost-effective 3D-printing technologies. Hexagonal honeycombs and their unit cell models were 3D-printed by both PolyJet™, using a photo-crosslinkable polymer, and fused deposition modeling (FDM) using a thermoplastic material. The state of the art digital image correlation (DIC) technique was employed as the experimental route in order to calculate the strain field during the deformation of... 

The trend in biomaterials development has now headed for tailoring the properties and making hybrid materials to achieve the optimal performance metrics in a product. Modern manufacturing processes along with advanced computational techniques enable systematical fabrication of new biomaterials by design strategy. Functionally graded materials as a recent group of hybrid materials have found numerous applications in biomedical area, particularly for making orthopedic prostheses. This article, therefore, seeks to address the following research questions: (RQ1) What is the desired structure of orthopedic hybrid materials? (RQ2) What is the contribution of the literature in the development of... 

Plasmonic nanostructures offer great enhancement of the Raman signal due to the strong confinement of the electromagnetic field. Thus, they are considered as suitable candidates for surface enhanced Raman spectroscopy (SERS). In this work, we present an alternative fabrication route, called the glancing angle deposition (GLAD), for tunable fabrication of plasmonic self-organized Ag nanoparticle arrays aimed at SERS. Using the GLAD technique, the inter-particle distance within the arrays can be made as small as 1 nm. Moreover, the plasmonic resonance can be precisely tuned over the whole visible range. The GLAD method can be up-scaled; and when a transparent substrate is used, it enables... 

In this work, we study the role of nanotextured ZnFe2O4/Fe2O3composite thin films fabricated by ultrasonic spray pyrolysis (USP) on the photoelectrochemical water oxidation reactions. The ZnFe2O4/Fe2O3 composites with different molar ratios are deposited on three-dimensional nanospikes (NSP) substrate, and the results are compared with those for planar devices. It is observed that optical absorption and charge separation due to larger surface area is significantly enhanced in nanotextured photoactive ZnFe2O4/Fe2O3 films. After characterization of ZnFe2O4/Fe2O3 composite films with different molar ratios (ZF1, ZF2, and ZF3), we find that the nanotextured ZF1 composite with a molar ratio of... 

Enhancing stability against photocorrosion and improving photocurrent response are the main challenges toward the development of cupric oxide (CuO) based photocathodes for solar-driven hydrogen production. In this paper, stable and efficient CuO-photocathodes have been developed using in situ materials engineering and through gold-palladium (Au-Pd) nanoparticles deposition on the CuO surface. The CuO photocathode exhibits a photocurrent generation of ∼3 mA/cm2 at 0 V v/s RHE. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) analysis and X-ray spectroscopy (XPS) confirm the formation of oxygen-rich (O-rich) CuO film which demonstrates a highly stable photocathode with retained... 

A new ternary nanocomposite based on graphene oxide (GO), polypyrrole (PPy) and vanadium pentoxide (V2O5) is obtained via one-step electrochemical deposition process. Electrochemical deposition of V2O5, PPy and GO on a stainless steel (SS) substrate is conducted from an aqueous solution containing vanadyl acetate, pyrrole and GO to get V2O5/PPy/GO nanocomposite. Characterization of the electrode material is carried out by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and atomic force microscopy (AFM). The electrochemical performance of the as-prepared nanocomposite is evaluated by... 

Alluring optical and electronic properties have made organometallic halide perovskites attractive candidates for optoelectronics. Among all perovskite materials, inorganic CsPbX3 (X is halide) in black cubic phase has triggered enormous attention recently owing to its comparable photovoltaic performance and high stability as compared to organic and hybrid perovskites. However, cubic phase stabilization at room temperature for CsPbI3 still survives as a challenge. Herein we report all inorganic three-dimensional vertical CsPbI3 perovskite nanowires (NWs) synthesized inside anodic alumina membrane (AAM) by chemical vapor deposition (CVD) method. It was discovered that the as-grown NWs have... 

We report on the results of a YBa2Cu3O7−x (YBCO) superconductive transition edge bolometer (TEB) fabricated on a Ce0.9La0.1O2−7 (CLO) buffered single crystalline yttria-stabilized zirconia (YSZ) substrate. Metal organic deposition was used for the fabrication of both the YBCO thin film as well as CLO buffer layer, while standard photolithography was applied for TEB preparation. YBCO thin film properties were analysed using scanning electron microscopy (SEM), X-ray diffraction (XRD), AC susceptibility and resistance versus temperature measurements. Optical response of the TEB in terms of voltage amplitude and phase was analysed and measured through four-probe technique in a liquid nitrogen...