Sharif Digital Repository

This research focused on the corrosion resistance and microstructure of hybrid additively manufactured (HAM) samples of AISI 420/CX (420/CX SS) stainless steels. Potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and Mott–Schottky analyses as well as the electrochemical noise (EN) technique were used to evaluate the electrochemical behavior of the as-built and heat-treated HAM parts in NaCl solution. The results showed a more protective passive layer formed on the CX SS side. The distribution of Cr-rich M23C6 carbides in matrix of 420 SS side resulted in a lower corrosion resistance compared to the CX SS side. The noise data analysis confirmed an increase in the... 

A label-free electrochemical biosensor was developed for the rapid detection of the matrix metalloproteinase 9 (MMP-9) biomarker on the basis of antibody immobilizing on the zinc oxide (ZnO) nanoparticle and ZnO nanorod electrodes. The charge transfer resistance (Rct) of the electrodes was used as the indicator for MMP-9 concentration, which was obtained through cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The ZnO nanorod-based biosensor exhibited linear behavior in the MMP-9 concentration range of 1–1000 ng/ml, which is a wider range than the available concentration ranges for most of the conventional methods. The biosensor sensitivity was 32.5 μA/(decade × cm2)... 

Electric field enhanced approach has been used to synthesize different copper hydroxide morphologies as high-performance supercapacitors electrode materials. Employing this efficient, simple and low cost method, various shapes such as rod, flower and cube with an average grain size of 30nm to 1μm were obtained on the copper substrate. The results revealed that applied electric field considerably accelerates the formation time of nanostructures from several days to close to 1min, where some of the desired nanostructures were obtained even in 1s. The electrochemical properties of different morphologies were compared using cyclic voltammograms and charge/discharge tests and electrochemical... 

Plasma electrolytic oxidation (PEO) process was employed to create ceramic coatings on titanium substrate by using silicate-based electrolytes containing different concentrations of alumina nanoparticles (0, 3, 6, and 10. g/lit). The effect of alumina nanoparticles concentration on the morphology, chemical and phase composition of the PEO coatings was investigated by scanning electron microscope, energy dispersive spectrometer, and X-ray diffractometer, respectively.The corrosion behavior of samples was studied by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) tests. SEM, EDS, and XRD analyses illustrated that alumina nanoparticles incorporated into the... 

TiO 2 nanorods, TiO 2 nanorod/TiO 2 nanoparticle and TiO 2 nanorod/ZnO nanoparticle composite structures were integrated as photoanodes in backside illuminated dye-sensitized solar cells (DSSCs). Incorporation of TiO 2 nanoparticles into the bare nanorods increased the dye loading and improved the short-circuit current density (J sc) from 2.22 mA/cm 2 to 3.57 mA/cm 2. ZnO nanoparticles electrochemically grown into the TiO 2 nanorod layer could increase the surface area. Nevertheless, this considerably reduced the J sc to 0.57 mA/cm 2 and consequently cell efficiency. Electrochemical impedance spectroscopy (EIS) results showed that ZnO incorporated samples have better effective diffusion... 

Among the various approaches, ZnS treatment is the most convenient method for reducing the charge recombination in quantum dot-sensitized solar cells (QDSSCs). Here an improved method of ZnS treatment is explained for efficiency enhancement in QDSSCs. To get to the goal of device performance improvement, it is essential to have a uniform deposited layer. We utilized Triton X-100 (TX-100) as a surfactant to the convenient aqueous precursors during ZnS deposition by successive ionic layer adsorption and reaction method. It helps to decrease in contact angle and increase in wettability of the aqueous precursor and results in a more uniform deposited layer. The effect of modified ZnS treatment... 

A key direction toward enhancing the long term and outdoor stability of the perovskite solar cells is encapsulation. As a result, a suitable encapsulation package is required to prevent moisture and oxygen penetration toward the perovskite solar cells. In this work, a low-cost commercially available bilayer structure of poly (methyl methacrylate)/ room-temperature vulcanizing silicone rubber (RTV) encapsulation package for enhancing the long term stability of the perovskite solar cells has been investigated. Encapsulated cells retained more than 80% of the initial efficiency at the environmental condition of 50% moisture, and room temperature after 1000 h, however reference cell efficiency... 

Herein, we present a novel, simple, and ultrasensitive electrochemical DNA (E-DNA) sensor based on hollow carbon spheres (HCS) decorated with polyaniline (PANI). A thiolated 21-mer oligonucleotide, characteristic of HBV DNA, is immobilized via electrodeposited gold nanoparticles on HCS-PANI. Cyclic voltammetry (CV), differential pulse voltammetry (DPV), and electrochemical impedance spectroscopy (EIS) are used to characterize the electrochemical properties of the prepared nanocomposite. Scanning electron microscopy is employed to investigate the morphological texture of the fabricated modifier. An enhanced intrinsic signal of PANI is probed to evaluate the biosensing ability of the prepared... 

The effect of NaOH content of electrolyte on the properties of ceramic coatings, produced in silicate solution, was studied. Morphology, chemical analysis, phase composition, and cross-section of the ceramic coatings were investigated by SEM, EDS, XRD, and OM, respectively. The corrosion resistance and corrosion mechanism were also studied using potentiodynamic polarization and electrochemical impedance spectroscopy in a 3.5% NaCl solution. To study the surface roughness, a brightness SEM image analysis method was used. Results suggested that increasing the NaOH concentration of sediment production size causes thickness and coating roughness to decrease. The lowest corrosion rate belonged to... 

A new poly (acrylonitrile) (PAN)-based gel polymer electrolyte (GPE) is fabricated to study the effect of carbon nanotube (CNT) on dye-sensitized solar cell (DSSC) efficiency. The GPEs are examined using electrochemical impedance spectroscopy (EIS) to analyze ionic conductivity. A maximum of 4.45 mS cm−1 ionic conductivity is achieved at room temperature with incorporation of 11 wt.% CNT. Performance of DSSC is examined with a solar simulator, and the highest energy conversion efficiency of 8.87% is achieved with the addition of 11 wt.% CNT. All GPE samples are found to follow Arrhenius model with temperature-dependent ionic conductivity testing. Structural properties are also characterized... 

A new poly (acrylonitrile) (PAN)-based gel polymer electrolyte (GPE) is fabricated to study the effect of carbon nanotube (CNT) on dye-sensitized solar cell (DSSC) efficiency. The GPEs are examined using electrochemical impedance spectroscopy (EIS) to analyze ionic conductivity. A maximum of 4.45 mS cm −1 ionic conductivity is achieved at room temperature with incorporation of 11 wt.% CNT. Performance of DSSC is examined with a solar simulator, and the highest energy conversion efficiency of 8.87% is achieved with the addition of 11 wt.% CNT. All GPE samples are found to follow Arrhenius model with temperature-dependent ionic conductivity testing. Structural properties are also characterized... 

In this study, the influences of different concentrations of SiO 2 nano sized particles in the bath on deposition rate, surface morphology and corrosion behavior of Ni-P-SiO2 Composite coatings were investigated. The deposition rate of coating was influenced by incorporation of SiO2 particles. The microstructure was investigated with field emission scanning electron microscopy (FESEM). The amount of SiO 2 was examined by Energy Dispersive Analysis of X-Ray (EDX) and amount of SiO2 nanoparticles co-deposited reached a maximum value at 4.5 %wt. Corrosion behavior of coated aluminum was evaluated by electrochemical impedance spectroscopy (EIS) and polarization techniques. The results... 

In this study, the surface morphology of Ni–P–SiO2 composite coating was investigated by field emission scanning electron microscopy (FESEM). The amount of SiO2 in the coating was examined by energy dispersive analysis of X-ray (EDX) and the Corrosion behavior of coating was evaluated by electrochemical impedance spectroscopy (EIS) and polarization techniques, showing the corrosion resistance of Ni–P–SiO2 diminished after heat treatment. The results showed that in the coating with 12.5 g/L SiO2, the coating hardness enhanced from 453VH to 980 VH before and after heat treatment. Furthermore, the wear behavior of the coating was analyzed before and after heat treatment  

In the present work, nano-composites of Ni-P-SiO2-Al2O3 were coated on AZ91HP magnesium alloy. The surface morphology of the nano-composite coating was studied by field emission scanning electron microscopy (FESEM). The amount of SiO2 in the coating was determined by energy-dispersive analysis of x-ray (EDX), and the crystalline structure of the coating was examined by x-ray diffractometer (XRD). All the experiments concerning the corrosion behavior of the coating carried out in 3.5 wt.% NaCl solution and evaluated by electrochemical impedance spectroscopy (EIS) and polarization technique. The results showed that an incorporation of SiO2 and Al2O3 in Ni-P coating at the SiO2 concentration of... 

The electrochemical behavior of lamotrigine (LMT) at the pyrolytic graphite electrode (PGE) is investigated in detail by the means of cyclic voltammetry. During the electrochemical reduction of LMT, an irreversible cathodic peak appeared. Cyclic voltammetric studies indicated that the reduction process has an irreversible and adsorption-like behavior. The observed reduction peak is attributed to a two-electron process referring to the reduction of azo group. The electrode showed an excellent electrochemical activity toward the electro-reduction of LMT, leading to a significant improvement in sensitivity as compared to the glassy carbon electrode. The results of electrochemical impedance... 

Magnesium (Mg) and its alloys have proved promising as biodegradable candidates for the repair of bone tissue. Despite the encouraging bio-related properties of Mg, its high corrosion rate in contact with body fluids still presents a major challenge. An efficient approach to address this issue is to provide a protective coating on Mg. The present research evaluates, for the first time, in vitro bioactivity and biocompatibility of a novel multifunctional composite coating based on poly(methyl methacrylate) (PMMA) biopolymer and bioactive glass (BG) particles on Mg-based implant. Electrophoretic deposition (EPD) was utilized to obtain this coating from a bi-component suspension. Coatings’... 

The electrocatalytic oxidation of methanol was studied over Ni, Co and Cu binary or ternary alloys on graphite electrodes in a NaOH solution (0.1 mol/L). The catalysts were prepared by cycling the graphite electrode in solutions containing Ni, Cu and Co ions at cathodic potentials. The synergistic effects and catalytic activity of the modified electrodes were investigated by cyclic voltammetry (CV), chronoamperometry (CA) and electrochemical impedance spectroscopy (EIS). It was found that, in the presence of methanol, the modified Ni-based ternary alloy electrode (G/NiCuCo) exhibited a significantly higher response for methanol oxidation compared to the other samples. The anodic peak... 

The aim of current research is to investigate the substrate electropolishing effect on corrosion resistance of Ni-Mo thin films. For this purpose, corrosion resistance of coatings deposited on mild steel substrates, that was electropolished or mechanically polished, have been compared in 3.5 wt.% NaCl solution using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The structural properties of Ni-Mo thin films were evaluated using X-ray diffraction (XRD) and their morphology, microstructure and chemical composition were also investigated using scanning electron microscopy (SEM) and X-ray energy dispersive spectroscopy (EDS). Temperature and acidity of deposition... 

Impedance characteristics of the negative electrode of lead-acid battery were derived on the basis of fundamental interfacial processes occurring at the electrode. The solution of the governing equations was presented in terms of a simple equivalent circuit consisting of resistive and capacitive loops in which charge transfer and sulfate layer formation and also mass transfer (Warburg) elements are considered. The kinetic parameters were deduced by fitting the theoretically derived impedance to the experimental data. Impedance at various States of Charge (SoC) was also examined  

In this work, a nanocomposite containing manganese dioxide (MnO2) modified reduced graphene oxide (rGO) supported bimetallic palladium-nickel (Pd-Ni) catalyst is prepared by electrodeposition method. The nanocomposite modifier film is prepared by forming a thin layer of graphene oxide (GO) via drop-casting of GO nanosheet dispersion on glassy carbon electrode (GCE), followed by electrochemical reduction of the film to provide rGO/GCE. Then, a two-step potential procedure is applied to deposit MnO2 nanoparticles on rGO/GCE. At the optimum deposition conditions, MnO2 nanoparticles with a thickness of 30-50 nm homogeneously covered the rGO surface (MnO2/rGO/GCE). Finally, the bimetallic Pd-Ni...