Sharif Digital Repository

This paper focuses on the effect of deep cryogenic treatment (-196 °C) on microstructure and mechanical properties of AZ91 magnesium alloy. The execution of deep cryogenic treatment on samples changed the distribution of β precipitates. The tiny laminar β particles almost dissolved in the microstructure and the coarse divorced eutectic β phase penetrated into the matrix. This microstructural modification resulted in a significant improvement on mechanical properties of the alloy. The steady state creep rates were measured and it was found that the creep behavior of the alloy, which is dependent on the stability of the near grain boundary microstructure, was improved by the deep cryogenic... 

In the new competitive dynamic market, manufacturing success and survival are becoming more and more difficult to ensure. In other words, getting the right product with low cost and high quality is not the only key to success. New requirements such as production responsiveness and flexibility should be considered. Reconfigurable Manufacturing System. (RMS) is a new paradigm that enables manufacturing systems to achieve rapid response to market demand. The effectiveness of an RMS depends on implementing key characteristics and capabilities of RMS in system design stage and benefiting from them in utilisation stage. In this paper, we introduced a methodology to adjust rapidly and productively... 

In industry, utilizing membrane separation technology to purify natural gas streams is of remarkable significance. Molecular Simulation was used in the current article to study the structural and gas separation properties of polydimethylsiloxane (PDMS)/zeolite 4A Mixed Matrix Membranes (MMMs). To explore the optimal performance of MMMs, several structural analyses, namely Fractional Free Volume (FFV), Radial Distribution Function (RDF), X-Ray Diffraction (XRD) and also Glass Transition Temperature (Tg) as one of the most important properties of membranes have been evaluated. Also, the solubilities and diffusivities of periodic cells were respectively measured using MSD and adsorption... 

PFC converters for higher power are commonly designed for continuous conduction mode (CCM). However, at light load, discontinuous conduction mode (DCM) will appear close to the crossover of the line voltage, causing the converter to switch between the two conduction modes. As a result, the converter dynamics change abruptly, producing input current distortion. In this article a piecewise affine approximation has been employed in modeling a boost power factor correction converter operated in the mixed conduction mode. This approach makes the new model very useful in large signal analysis of PFC rectifiers and design of controller. The results obtained from the proposed model are compared with... 

An increasing trend for reducing cost, space, and weight leads to modern embedded systems that execute multiple tasks with different criticality levels on a common hardware platform while guaranteeing a safe operation. In such Mixed-Criticality (MC) systems, multiple Worst-Case Execution Times (WCETs) are defined for each task, corresponding to system operation mode to improve the MC system’s timing behavior at run-time. Determining the appropriate WCETs for lower criticality modes is non-trivial. On the one hand, considering a very low WCET for tasks can improve the processor utilization by scheduling more tasks in that mode, on the other hand, using a larger WCET ensures that the mode... 

Integrally skinned asymmetric membranes for the separation of O 2 and N 2 were fabricated by the phase inversion technique from polysulfone, polyetherimide, and polyimide. Two types of surface modifying macromolecules (SMMs) including hydrophilic SMM (LSMM) and charged SMM (cSMM) were synthesized and blended with the casting solution to modify the membrane surface. The cast film was then immersed in the first coagulant alcohol (methanol, ethanol, or isopropanol) for a predetermined period, before being immersed in the second coagulant (water). The SMMs used in these experiments were laboratory synthesized by the two-step process of polyurethane prepolymer synthesis and end capping, before... 

A new method for fluorescent microscopy has been proposed. Proposed method uses indirect excitation of fluorophores with nanometer localized illuminating source. Localized source is created at corners of gold nanotriangles which are deposited on glass substrate. Actually the combination of gold nanotriangle (deposited on glass) acts as active substrate (where species will be placed) for our proposed method. The structure will be scanned with a focused beam of laser (or combination of beams). Due to electric field enhancement in corners and edges of nanotringle (because of surface plasmons), third order nonlinear effect will be enhanced accordingly. Enhancement in third order nonlinearity... 

Evaporation of polymeric solid fuels in backward facing step geometry subject to an inlet oxidizer flow at elevated temperatures is considered and convective heating of the fuel surface by the hot oxidizing inlet flow and subsequent mixing of the evaporated fuel with the oxidizer flow and its combustion is numerically studied. The objective of this work is to gain insight into the auto-ignition of the fuel and its controlling parameters in this configuration. The system of governing equations is solved with a finite volume approach using a structured grid in which the AUSM scheme is used to calculate the gas phase convective fluxes. The flowfield is turbulent and the SpalartAllmaras... 

The effect of Rare earths addition to AZ91 magnesium alloy and its influence on the microstructure and mechanical properties was investigated in this study. Addition of cerium rich misch metal to AZ91 alloy resulted in formation of needle shape particles, which had a very high thermal stability, providing superior mechanical properties compared to AZ91 magnesium alloy. As a result, the grain boundaries were less susceptible for grain boundary sliding at high temperatures. The steady state creep rates were specified and for the AZ91 alloy and the results indicate a mixed mode of creep behavior, with some grain boundary effects contributing to the overall behavior. However for the RE added... 

In the present study, the performance of three moving bed biofilm reactors (MBBRs) has been evaluated in series with anaerobic/anoxic/oxic (A2O) units for simultaneous removal of organic matter and nutrients (nitrogen and phosphorous) from a synthetic wastewater with characteristics similar to those of a typical municipal wastewater. Response surface methodology based on central composite design was used to investigate the effects of nitrate recycle ratio, hydraulic retention time (HRT), and influent chemical oxygen demand (COD) on the organic and nutrient removal and optimization process. The optimized values of influent COD, HRT, and R were 462 mg/L, 10 h, and 3.52, respectively. The... 

Systemic inflammation biomarkers have been associated with risk of cardiovascular morbidity and mortality. We aimed to clarify associations of acute exposure to particulate matter (PM10(PM < 10 μm), PM2.5-10(PM 2.5–10 μm), PM2.5(PM < 2.5 μm), PM1-2.5(PM 1–2.5 μm), and PM1 (PM < 1 μm)) with systemic inflammation using panels of elderly subjects and healthy young adults. We followed a panel of 44 nonsmoking elderly subjects living in a retirement home and a panel of 40 healthy young adults living in a school dormitory in Tehran city, Iran from May 2012 to May 2013. Blood biomarkers were measured one every 7–8 weeks and included white blood cells (WBC), high sensitive C-reactive protein... 

Non-pumping reactive wells (NPRWs) filled by zero-valent iron (ZVI) can be utilized for the remediation of groundwater contamination of deep aquifers. The efficiency of NPRWs mainly depends on the hydraulic contact time (HCT) of the pollutant with the reactive materials, the extent of the well capture zone (Wcz), and the relative hydraulic conductivity of aquifer and reactive material (Kr). We investigated nitrate removal from groundwater using NPRWs filled by ZVI (in nano and micro scales) and examined the effect of NPRWs orientations (i.e. vertical, slanted, and horizontal) on HCT and Wcz. The dependence of HCT on Wcz for different Kr values was derived theoretically for a homogeneous and... 

The effect of Al content and Si addition on the microstructural and creep properties of Mg-Al-RE alloys was investigated in this study. The steady state creep rates were specified and it was found that the creep behavior of the alloy, which is dependent on the stability of the near grain boundary microstructure, was improved by the RE and Si addition. For the AZ91 alloy, the results indicate a mixed mode of creep behavior, with some grain boundary effects contributing to the overall behavior. However for the RE and Si added samples, sliding of grain boundaries was greatly suppressed and the dislocation climb controlled creep was the dominant deformation mechanism. Analysis of creep rates... 

Various compositions of maleated ethylene-propylene-rubber (EPR-g-MA) toughened polyamide 6 without and with short glass fiber, i.e. 5-20 wt.% rubber and 5-20 wt.% fiber, are prepared using an industrial twin-screw extruder at different levels of feed rate (100-250 kg/h), screw speed (200-450 rpm) and barrel temperature (230-260 °C). Trial runs designed based on the Taguchi's orthogonal arrays are subjected to tensile, impact, scanning electron microscopy (SEM) and optical microscopy tests; and the results are used to perform the analysis of variance (ANOVA). It is shown that the rubber particle size decreases significantly by increasing the rubber content for the unreinforced blend. The... 

The liquid-liquid extraction process is well-known for its complexity and often entails intensive modeling and computational efforts to simulate its dynamic behavior. This paper presents a new application of the Genetic Algorithm (GA) to predict the modeling parameters of a chemical pilot plant involving a rotating disc liquid-liquid extraction contactor (RDC). In this process, the droplet behavior of the dispersed phase has a strong influence on the mass transfer performance of the column. The mass transfer mechanism inside the drops of the dispersed phase was modeled by the Handlos-Baron circulating drop model with consideration of the effect of forward mixing. Using the Genetic Algorithm... 

Nanostructured TiO2-ZrO2 thin films and powders were prepared by a straightforward aqueous particulate sol-gel route. Titanium (IV) isopropoxide and zirconium (IV) acetate hydrate were used as precursors, and hydroxypropyl cellulose was used as a polymeric fugitive agent in order to increase the specific surface area. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy revealed that the powder were crystallised at the low temperature of 500 °C, containing anatase-TiO 2 and tetragonal-ZrO2 phases. Furthermore, it was found that ZrO2 retarded the anatase-to-rutile transformation up to 900 °C. The activation energies for crystallite growth of TiO2 and ZrO2 components in... 

Mean field independent component analysis (MF-ICA) along with other chemometric techniques was proposed for obtaining more information from multi-component gas chromatographic-mass spectrometric (GC-MS) signals of essential oils (mandarin and lemon as examples). Using these techniques, some fundamental problems during the GC-MS analysis of essential oils such as varying baseline, presence of different types of noise and co-elution have been solved. The parameters affecting MF-ICA algorithm were screened using a 25 factorial design. The optimum conditions for MF-ICA algorithm were followed by deconvolution of complex GC-MS peak clusters. The number of independent components (ICs) (chemical...