Sharif Digital Repository

Amine-functionalized MIL-101(Cr) has been synthesized by hydrothermal (MNH2) and post-synthetic modification (MNH2-p) approaches. Pd/MNH2 and Pd/MNH2-p have been tested in CO oxidation reaction as a gas phase reaction to clarify the difference between two synthesis approaches. Their performance has also been compared with that of Pd supported on MIL as a common MOF and CuBTC as a commercial one. The results show the significant difference between Pd/MNH2-p and Pd/MNH2, where CO conversion of 100% was not observed for Pd/MNH2-p, whereas Pd/MNH2 outperformed the others and exhibited the high reaction rate thanks to the active sites created by amorphization during the reduction process because... 

Various mixtures of surfactants and nanosilica particles were investigated to assess their influence on rising bubble hydrodynamics. For this purpose, local velocities of rising bubbles were measured experimentally. Also, the effects of concentration of three types of surface-modified silica nanoparticles on density, viscosity, and surface tension of surfactant solutions were determined. Experimental results revealed that the simultaneous presence of nanoparticles and surfactant molecules led to the decrease of local velocities of rising bubbles. The presence of nanoparticles in surfactant solutions leads to a more reduction of bubble local velocity. This could be caused by the formation of... 

Nowadays, superhydrophobic surfaces have attracted a lot of interest because of the wide range of applications in industries. These surfaces can significantly reduce the drag force due to the formation of air gaps between the substrate and liquid interface. The present review mainly focuses on the very recent progresses in the drag reduction studies using superhydrophobic surfaces. Also, a brief discussion about the mathematical modeling and the theories of superhydrophobic surfaces, natural water repellent surfaces, various fabrication techniques with advantages and disadvantages of each method and different properties of the fabricated surfaces in industrial applications is presented.... 

Foam flooding has been applied as a promising method in enhanced oil recovery to obviate the challenges of gas flooding such as fingering, channeling and overriding. However, long-term foam stability is crucial for mobility control. In this work, the effective mechanisms on foam stability in the presence of CaCO3 nanoparticles were assessed both theoretically and experimentally. The static and dynamic behaviors of cationic surfactant (HTAB) foam in the presence of CaCO3 nanoparticles with different hydrophobicity were evaluated. The CaCO3 nanoparticles were treated with a series of long-chain fatty acids to generate a range of wettability. Afterward, the underlying mechanisms were revealed... 

The stress fields of cylindrical and spherical multi-phase inhomogeneity systems with perfect or imperfect interfaces under uniform thermal and far-field mechanical loading conditions are investigated by use of the Boussinesq displacement potentials. The radius of the core inhomogeneity and the thickness of its surrounding coatings are arbitrary. The discontinuities in the tangential and normal components of the displacement at the imperfect interfaces are assumed to be proportional to the associated tractions. In this work, for the problems where the phases of the inhomogeneity system are homogeneous, the exact closed-form thermo-elastic solutions are presented. These solutions along with a... 

There is a long-standing question about the molecular configuration of interfacial water molecules in the proximity of solid surfaces, particularly carbon atoms, which plays a crucial role in electrochemistry and biology. In this study, the dielectric, structural, and dynamical properties of confined water placed between two parallel graphene walls at different interdistances from the angstrom scale to a few tens of nanometer have been investigated using molecular dynamics. For the dielectric properties of water, we show that the dielectric constant of the perpendicular component of water drastically decreases under sub-2-nm spatial confinement. The dielectric constant data obtained through... 

There is a long-standing question about the molecular configuration of interfacial water molecules in the proximity of solid surfaces, particularly carbon atoms, which plays a crucial role in electrochemistry and biology. In this study, the dielectric, structural, and dynamical properties of confined water placed between two parallel graphene walls at different interdistances from the angstrom scale to a few tens of nanometer have been investigated using molecular dynamics. For the dielectric properties of water, we show that the dielectric constant of the perpendicular component of water drastically decreases under sub-2-nm spatial confinement. The dielectric constant data obtained through... 

The present work investigates joining of two MoSi2 parts through Cusil/Zr/Cusil interlayer with Cusil being a commercial eutectic of Cu-Ag alloy. The joining operation was implemented in an inert gas tube furnace by brazing. The brazing temperature ranged from 800 to 930°C while the operation lasted for 60min. Evaluation of joints strength through shear loading identified the maximum strength 60.31MPa for the brazed sample at 830°C. Interfacial microstructure was studied by Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and X-ray Diffraction (XRD) techniques. Applying the temperature of 830°C was led to a uniform dense joint consisting of various phases with... 

This paper has developed an axisymmetric laminar and turbulent two-phase flow solver to simulate pressure-swirl atomizers. Equations include the explicit algebraic Reynolds stress model, the Reynolds-averaged Navier-Stokes, and the level set equation. Applying a high-order compact upwind finite difference scheme with the level set equation being culminated to capture the interface between air-liquid two-phase flow and decreasing the mass conservation error in the level set equation. The results show that some recirculation zones are observed close to the wall in the swirl chamber and to the axis. This model can predict converting the Rankin vortex in the swirl chamber to the forced vortex in... 

Mixed protein-surfactant adsorption layers can be built up in two different ways. The classical way is when all components adsorb simultaneously from a mixed solution. Alternatively, the components adsorb one after another, i.e. in a sequential way. In the present work, the formation of such surface layers has been studied with the random coil protein β-casein in the presence of added anionic surfactant SDS and compared for two different interfaces: the water-air (W-A) and water-hexane (W-H) interfaces. The used experimental technique is a drop profile analysis tensiometer PAT-1 specially equipped with a coaxial double capillary for drop volume exchange during the experiments. The results... 

Recent investigations show that ceramic/ceramic joints have high potential for applications in industry. Cost and difficulty in manufacturing complex components, either in one step or by joining of ceramic-metal and ceramic-ceramic, have inhibited more widespread use. It is important to know how to join components without problems and to understand the role of the interface as the main factor controlling the properties in these joints. The purpose of this paper was to investigate the joining of two ceramics with metal fillers (SiC to SiC and Al2O3 to Al2O3) and to investigate the interface of SiC/SiC and Al2O3/Al 2O3 with the same metal interlayer (Ag-Cu-Ti) and the effects on the... 

Al-1100/St-12 aluminum clad steel sheets were produced using roll bonding process at different reductions in thickness and with various supplemental annealing treatments. Experiments were conducted by applying the Taguchi method to obtain optimum condition for maximizing the joint strength. The joint strengths of the bi-layer sheets were evaluated by peel test. The Al/Fe intermetallic phases at the joint interface and the peeled surfaces were examined using scanning electron microscopy (SEM). Energy dispersive spectroscopy (EDS) and Vickers microhardness test were performed to characterize the intermetallic compounds. The results indicate that at the optimum condition of 0.50 reduction in... 

Microstructural development and phase formation at the interface of yttria stabilized zirconia (3Y-TZP)/430L stainless steel composite layers produced by co-sintering method were studied by SEM, HRTEM, micro-focus XRD, and EPMA. Formation of a rich chromium boundary layer at the interface was noticed, which revealed Cr aggregation at the interface at the elevated temperatures. Misfit dislocations were also observed at the joint interface to tackle the mismatch crystallographic orientations between the ceramic and metal layer. The results of the micro-focus XRD showed formation of no new phases at the boundary zone. Microstructural studies also revealed a retarded grain growth in the... 

The thermal decomposition of Aluminum Titanate in exposure to pure Aluminum was examined both in powder and in bulk form. Optical microscopy, FE-SEM, XRD, DSC and TGA examinations were conducted to take the possible chemical reactions between Aluminum Titanate and Al into consideration. It was found that as Aluminum Titanate particles are exposed to Al matrix, the thermal stability of Aluminum Titanate is degraded and its decomposition temperature is reduced from 850°C to 550°C. Also, the chemical reactions between Aluminum Titanate and Al start along the interfaces, and the reaction products, i.e. Al3Ti, Al2O3, TiO2 and O2 gas are left there. A mechanism was suggested to describe the... 

In order to safe design and optimize performance of industrial systems which work under two phase flow conditions, it's often needed to categorize flow into different regimes. In present work the experiments of two phase flow were done in a large scale test facility with length of 6m and 5cm diameter. Four main flow regimes were observed in vertical air-water two phase flows at moderate superficial velocities of gas and water: Bubbly, Slug, Churn and Annular. Some image processing techniques were used to extract information from each picture. This information include number of bubbles or objects, area, perimeter, height and width of objects (second phase).Also a texture feature extraction... 

The purpose of this paper is to investigate the effects of annealing phenomena on the energy absorption of Al-steel bilayer sheets, bonded by cold rolling, through wedge tearing. Tearing by wedge is a dissipating energy system that includes three components: cutting, friction and plastic deformation due to bending. In order to find the bonding and annealing effects on energy absorption, the non-bonded bilayer sheets are prepared in the same condition of bonded ones. The results show that energy absorption of bonded sheets is larger than that of non-bonded ones. This is due to different plastic bending moment of bonded and non-bonded bilayer sheets. Whenever the bond is improved by heat... 

Attempts were made to trace the effect of organoclay (OC) on the rheological and mechanical behaviors of the low density polyethylene (LDPE)/ethylene-vinyl acetate (EVA) blends. To do this effectively, in addition to LDPE/EVA/OC system, pure LDPE and LDPE/EVA blends were also examined as model systems. The rheological behavior was determined by the capillary rheometer. Morphological characterization was also carried out using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and theoretical approach based on interfacial energies. Shear viscosity, tensile strength and elastic modulus of LDPE/EVA were found to decrease by increasing the EVA... 

The mechanism of interface formation during sinter-joining of nanostructured yttria stabilized zirconia (27 nm) compacts with chromium powder was investigated. The effect of sintering atmosphere, i.e. argon or vacuum, was studied. Microstructural evaluation and phase formation was examined by scanning electron microscopy (SEM), electron probe micro-analysis (EPMA), and micro-focused X-ray diffraction (MFXRD) methods. It is shown that spreading and evaporation-condensation mechanisms are responsible for the interface formation. An improved joint shear-strength was obtained after sintering in vacuum (74 MPa) compared with argon (41 MPa). The result of MFXRD indicated formation of Cr-island at... 

With the decline in oil discoveries over recent decades, it is believed that enhanced oil recovery (EOR) technologies will play a key role to meet energy demand in the coming years. Polymer flooding is used commonly worldwide as an EOR process. In this work, we propose the synthesis of protected polyacrylamide (PAM) nanoparticles (PPNs) with a hydrophobic polystyrene (PSt) shell by one-pot two-step inverse emulsion polymerization, in which the PSt shell was created by surface polymerization. The shell protects the active PAM chains from premature degradation caused by the harsh environment in the reservoirs, controls the release of the chains as rheological modifiers, and additionally, it... 

In this work, we present a level set method to simulate steady and unsteady mass transfer from a single droplet moving in a second phase fluid under buoyant force. We initially use level set to determine the interface between the two phases, where the shape of drop forms. Next, we extend this method to solve a unique mass transfer equation for the entire solution domain without considering the discontinuity appeared at the interface. We use a finite element method incorporated with the characteristic-based split (CBS) algorithm to implement axi-symmetric mass transfer equations on a stationary Eulerian grid. Of course, the convection-diffusion modeling of mass transfer is different from the...