Sharif Digital Repository

Different architectures of layered laminates comprising two exterior layers of Al-Mg-Si/SiC metal matrix composite and an Al1050 ductile interlayer were fabricated by means of hot roll-bonding with applying different strains of εr = 39%, 51%, and 63%. For monolithics production, ceramic particulate reinforcement contents of 0, 5, 10, and 15 vol% were utilized. The aim of introducing ductile metal interlayer was to compensate the low toughness of composite layers and consequently enhancement of damage tolerance of bundled structures along with prevention of their catastrophic failure through activation of extrinsic toughening mechanism. Effects of architectural characteristics and fabrication... 

Dominant Collapse Mechanisms (DCMs) have been reported to play an important role in collapse capacity of structural systems and the seismic losses consequent to it. Therefore, DCMs of Reinforced Concrete (RC) frames have been studied, in this article, considering Record-To-Record (RTR) and modeling uncertainties. Two sets of RC frames have been designed, in this regard, that share the design assumptions but contain different levels of over-strength. Each set contains 26, 4- to 20-story nonlinearly modeled frames. Initially, Incremental Dynamic Analysis (IDA) was used to identify frames' DCMs. Then, the RTR variability reflected through IDA was combined with spectral shape and pulse effects... 

Bond durability of FRP bars and concrete is an important issue to the overall integrity and long-term performance of a strengthening structure. This paper examines the bond durability of GFRP bars embedded in different types of concrete (Normal, self-compacting, light weight, and high strength) exposed to aggressive environments, namely, sea water, alkaline, and acid. A total of 132 specimens were tested in direct pull-out. The development lengths of both control and conditioned specimens were obtained and compared to the current standards. The results revealed bond strength reductions of 0–21% for the light weight, 1–16% for the normal, 5–9% for the high strength, and 4–12% for the... 

The aim of the present study is to investigate the effects of using hybrid fibers on rheological, mechanical and durability properties of the high-strength self-consolidating concrete (SCC). For this purpose, two types of fibers including hooked-end steel fibers and polypropylene fibers were used. In this study, a total of eleven mixtures were used: one as a control mix, one containing 0.5% steel fibers, four containing 0.5% hybrid fibers (steel and polypropylene), one containing 1.0% steel fibers and the four containing 1.0% hybrid fibers (steel and polypropylene). For investigating the rheological properties, slump flow, J-ring and V-funnel tests were performed. Mechanical properties were... 

A new refill friction spot welding process called Threaded Hole Friction Spot Welding (THFSW) was introduced to join AA5052 aluminum to short-carbon-fiber-reinforced polypropylene (PP-SCF) composite sheets. The process was based on filling of the pre-threaded hole by melted and re-solidified polymer. The results showed that THFSW was successful to join aluminum to polymer sheets and the hole was completely filled with melted polymer. Formation of a reaction layer composed mostly of Al, C and O as well as interlocking between the threaded hole and the re-solidified polymer were recognized as main bonding mechanisms. Maximum shear-tensile strength of the joints reached to ∼80 percent of the... 

This study presents a framework that utilizes Bayesian regression to create probabilistic cost models for retrofit actions. Performance improvement is the key parameter introduced in the proposed framework. The incorporation of this novel feature facilitates the characterization of retrofit cost as a continuous function of the desired performance improvement. Accounting for the performance gained from retrofit enables the use of the models in determining the optimal level of retrofit. Furthermore, accounting for the model uncertainty facilitates the use of the models in risk and reliability analyses. The proposed framework is applied to create seismic retrofit cost models for masonry school... 

During the past decades, development of reinforcing materials caused a revolution in the structure of high strength and high performance cement-based concrete. Among the most important and exciting reinforcing materials, Steel Fiber (SF) becomes a widely used in the recent years. The main reason for addition of SF is to enhance the toughness and tensile strength and limit development and propagation of cracks and deformation characteristics of the SF blended concrete. Basically this technique of strengthening the concrete structures considerably modifies the physical and mechanical properties of plain cement-based concrete which is brittle in nature with low flexural and tensile strength... 

Polycarboxylate superplasticizers based on acrylic acid (AA) and maleic anhydride (MAn) were synthesized via free-radical copolymerization with an ethylene glycol monomer and characterized. The copolymerization temperature (ranging from 50 to 90 °C) appeared to be the key operating factor governing the chemical structure of the superplasticizers. The chemical structures of the products were analyzed by gel permeation chromatography, whereas an optimized sample was further analyzed by Fourier transform infrared spectroscopy and 1H-NMR. Superplasticizers of the AA and MAn classes were then incorporated into concrete, and their performances were measured by slump and slump loss tests, where a... 

Nowadays, by adding a small amount (about 0.5–5% by weight) of a desired nanomaterial to a matrix having certain properties one may design a multifunctional nanocomposites with a remarkably improved macroscopic properties of interest. The capability of conventional continuum theories in treating the problems of embedded ultra-small inhomogeneity with any of its dimensions comparable to the characteristic lengths of the involved constituent phases is questioned, mainly, on the grounds of the accuracy and the size effect. The micromechanical framework based on the Eshelby's ellipsoidal inclusion theory [1] which has been widely used to estimate the overall behavior of composites falls under... 

Reinforcement of polydimethylsiloxane (PDMS) was investigated using untreated nanodiamond (uND) and silane functionalized ND (sND) at various degrees of silanization. Scanning electron microscopy revealed an improved dispersion of ND in PDMS by silanization. The incorporation of uND and sNDs enhanced tensile strength up to 45% and 70%, respectively; however, greater improvement was observed for sNDs at very low concentrations, e.g. 0.2 wt%. The much improvement in crosslinking density, analyzed by Flory-Rehner model and Mooney-Rivlin plot, and interfacial interaction, characterized by Kraus and Cunneen-Russell plots, was also observed for sNDs. Interestingly, it was found that the extent of... 

The bond of fiber-reinforced polymer (FRP) reinforcement is expected to be more sensitive to the strength and geometry of the ribs than conventional steel reinforcement. In this study, the effect of carbon fiber mat anchorage on the pullout behavior of glass fiber-reinforced polymer (GFRP) bars embedded in normal concrete is studied. The studied parameters were the compressive strength of the concrete (16 MPa, 24 MPa, and 37 MPa), and, the length and diameter of the anchorage. In total, 15 variables were studied. Ribbed GFRP bars with 10 mm nominal diameter and 80 mm embedment length, ld, (which is 8 times the bar diameter) were considered. Based on the results for concretes with the... 

The interfacial behavior of composites is often simulated using a cohesive zone model (CZM). In this approach, a traction-separation (T-S) relation between the matrix and reinforcement particles, which is often obtained from experimental results, is employed. However, since the determination of this relation from experimental results is difficult, the molecular dynamics (MD) simulation may be used as a virtual environment to obtain this relation. In this study, MD simulations under the normal and shear loadings are used to obtain the interface behavior of Al/Al2O3 composite material and to derive the T-S relation. For better agreement with Al/Al2O3 interfacial behavior, the exponential form... 

This study deals with the elastodynamic response of a surface-stiffened transversely isotropic half-space subjected to a buried time-harmonic normal load. The half-space is reinforced by a Kirchhoff thin plate on its surface. By virtue of a displacement potential function and appropriate time-harmonic Green’s functions of transversely isotropic half-spaces, a robust solution corresponding to two plate-medium bonding assumptions, namely (a) frictionless interface, and (b) perfectly bonded interface is obtained for the first time. All elastic fields of the problem are expressed explicitly in the form of semi-infinite line integrals. Results of some limiting cases including isotropic materials,... 

Copper matrix composites reinforced with TiO2particles are promising materials widely used as contact materials due to their excellent mechanical and physical properties such as good electrical and thermal conductivity and strength at high temperature. In this research, the novel contact material were prepared by in-situ oxidation of Cu-Ti pre alloyed powders. The morphology of milled powders and microstructure of nano-composite specimens were studied by SEM and TEM. To evaluate mechanical alloying progress of Cu and Ti powders mixture and internal oxidation after Cu2O addition, XRD analysis were carried out. The Physical and mechanical properties results of specimens indicate that the... 

In this paper, thermal buckling and free/forced vibration characteristics of size-dependent composite cylindrical nanoshell reinforced with graphene platelets (GPLs) is presented. Also, the nanoshell is embedded in an elastic pasternak medium, which is obtained by adding a shear layer to the Winkler model. The present nano-resonator is based on a vibrating first order nanoscale cylindrical shell subjected to transverse pressure. The temperature-dependent material properties of piece-wise functionally graded graphene-reinforced composites (FG-GRCs) are assumed to be graded in the thickness direction of a cylindrical nanoshell and are estimated through a nanomechanical model. Also, Halpin–Tsai... 

In the present study, Lactobacillus plantarum PTCC 1058 was microencapsulated in Alginate-chitosan blended beads based on ionically dual cross-linking by Na-tripolyphosphate (Na-TPP). The homogenous solution of bacteria and alginate was dripped into the gelling bath of calcium chloride. After 30 min hardening, filtrate beads were transferred into the solution of chitosan. Dual cross-linked gel beads were prepared by employing Na-TPP solution to the chitosan coated beads. Morphology, particle size, alginate-chitosan interaction, characterizing the structure of single and dual cross-linked beads were determined by using scanning electron microscopy SEM, FTIR and XRD analysis. FTIR analysis... 

This research investigated the long-term environmental effects on bond strength at the interface between fiber- reinforced polymers (FRPs) and timber. A total of 581 timber specimens were bonded with seven types of FRP sheets (unidirectional and bidirectional glass, carbon, aramid, and hybrids) using a wet lay-up technique. The specimens were exposed to acidic, alkaline, fresh water, and sea water solutions with pH of 2.5, 7, 7.25, 10, and 12.5 for 1, 3, 6, 9, and 12 months. A chamber was also used to simulate ultraviolet radiation after 6 months. A series of single-lap shear tests were then conducted to determine the interfacial bond strength reduction. The results showed that bidirectional... 

This paper investigates the dynamic response of a clamped-free CNT-reinforced-MRE beam which is actuated by the combination of a constant and a harmonic time-dependent magnetic field. Using Hamilton's principle, the equation of motion has been obtained and discretized using the Galerkin method. This procedure transforms the governing PDE equation of motion into a nonlinear ODE equation in the form of the nonlinear Mathieu equation with cubic damping. Then, the method of multiple scales is employed to obtain the dynamic response of the system. Furthermore, a stability analysis is also performed and the effects of a magnetic field on the dynamic response and stability of the system is...