Sharif Digital Repository

A 2D numerical investigation is performed to better understand the transient thermo-fluid processes in a vortex tube for a cold mass fraction equal to0.44. The results along the Ranque-Hilsch vortex tube reveal a close agreement with past numerical and experimental data. The distribution of axial, radial, and tangential velocities as well as the stagnation pressure and temperature are examined at different positions for different time steps. The results indicate that the tangential velocity is the most significant velocity component and dominates the heat transfer and energy conversion processes. In addition, it is evident that the core of the cold end experiences the highest pressure... 

The safe operating condition for the vacuum tubes is very important and critical since they are very expensive and delicate. Providing limited short circuit energy for the vacuum tube and fast transferring from the short circuit to the nominal operation state are absolutely necessary. Extant protection strategies threat the availability of the vacuum tubes. In addition, they cannot completely protect the tube due to the delay of the fault detection system. This article proposes a high voltage (HV) short circuit fault current limiter which can limit the short circuit energy of the system inherently. The proposed structure activates automatically when the current exceeds the predetermined... 

In conventional high-voltage power supplies used for driving the microwave tubes, the shunt crowbar, which generally consists of series-connected thyristors, protects the microwave tube against the vacuum arc fault. In the case of arc fault, the thyristor-based crowbar is closed as a parallel path and diverts the fault current through itself. It avoids serious damage to the microwave tube. However, thyristor switches usually have a limited rate of rise of ON-state current (di/dt), which necessitates placing a series inductor in the crowbar path. Thus, satisfying all protection limits of microwave tubes-including the injected fault energy and the fault current interruption time-is a... 

Vacuum arc is one of the most important failure factors of the vacuum tubes. The amount of delivered energy from the high-voltage dc power supply to the vacuum tube is an important issue during the vacuum arc in the tube. Vacuum arc acts as a short-circuit fault (SCF) at the power supply output. The majority of converters use a single current sensor to measure only the converter output current for detecting the SCF. However, the sensor may provide unreliable data because of the noise effect. Application of a low-pass filter reduces the noise effect. Regarding the delay of the low-pass filter, the interval of arc detection increases and more energy is delivered to the tube. In this article, a... 

Alumina is widely used as a vacuum ceramic separator in the pillbox-type output window of high-power electron tubes. The fracture of alumina is one of the most important factors in the failure of these tubes. In this article, the fracture process of alumina in the pillbox-type window of high-power electron tubes is assessed microscopically. The investigation shows the twinning phenomenon in the fractured alumina. The reason for initiating and propagating twins is also investigated. An increase in the alumina temperature decreases the required stress level for generating twins. The overheating condition occurs due to an impedance mismatch in the pillbox-type window. Experimental and numerical... 

The absorber is an important component in absorption machines and its characteristics have significant effects on the overall efficiency of absorption machines. This article reports on the results of numerical studies on the characteristics of falling film LiBr-H2O solution on a completely wetted horizontal tube and the associated vapor absorption in the Reynolds number range of 5 < Re < 100. The boundary layer assumptions are used for the transport of mass, momentum and energy equations and the finite difference method is employed to solve the governing equations in the film flow. The heat and mass transfer coefficients are expressed in the forms of Reynolds number, Prandtl number and... 

A brass vortextube is used to carry out a series of experiments. The main objective of the present research is to investigate the separation performances of a vortex tube (VT) for a hydrocarbon mixture. Examination is also applied to study the effects of nozzle intakes number and cold fraction on the gas species separation at specific inlet pressure 236.37 kPa in a VT with two gas mixtures (LPG as a hydrocarbon mixture and LPG-N2). A two-dimensional computational fluid dynamic (CFD) model simulation of a VT is presented. CFD code after validation is also applied to investigate the role of cold fraction and nozzle intakes number on the gas species separation. The highly rotating flow field... 

The evolution of microstructure and the mechanical properties of an aluminum 6061 alloy tube subjected to a novel severe plastic deformation process called tube channel pressing were studied. Results show that the tube channel pressing causes an impressive grain refinement and strengthening of the material. As an illustration, mostly ultrafine grained tube (D-=760nm) bearing the yield strength of 352. MPa can be obtained after 5 passes of tube channel pressing. Additionally, the tube channel pressing causes the heterogeneous grain refinement resulting in a bimodal distribution of size of grains after 7th pass. Therefore, it can be inferred that the main microstructure refining mechanism... 

Radial forging is an open die forging process used for reducing the diameters of shafts, tubes, stepped shafts and axles, and for creating internal profiles in tubes. Due to very large forging loads, the tool should withstand high stress and wear. Therefore, the success of the forging process depends upon recognition of the die failure factors and optimization of the tool working conditions that enhance tool life. In this study, the effect of process parameters on tool life in the cold radial forging process is investigated using nonlinear three dimensional finite element modeling. Wear and mechanical fatigue are considered as the main modes of tool failure, and a parametric study on the... 

This research study presents an experimental investigation on forced convection heat transfer of an aqueous ferrofluid flow passing through a circular copper tube in the presence of an alternating magnetic field. The flow passes through the tube under a uniform heat flux and laminar flow conditions. The primary objective was to intensify the particle migration and disturbance of the boundary layer by utilizing the magnetic field effect on the nanoparticles for more heat transfer enhancement. Complicated convection regimes caused by interactions between magnetic nanoparticles under various conditions were studied. The process of heat transfer was examined with different volume concentrations... 

In this study, failure of a high pressure economizer tube of a boiler used in gas-Mazut combined cycle power plants was studied. Failure analysis of the tube was accomplished by taking into account visual inspection, thickness measurement, and hardness testing as well as microstructural observations using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and x-ray diffraction (XRD). Optical microscopy images indicate that there is no phase transformation during service, and ferrite-pearlite remained. The results of XRD also revealed Iron sulfate (FeSO4) and Iron hydroxide sulfate (FeOH(SO4)) phases formed on the steel surface. A considerable amount of Sulfur was also... 

In this work, the 6061 aluminum alloy tubes are severely deformed through a novel method called Tube Channel Pressing (TCP). The ability of this process in improving mechanical properties, grain refinement and microstructural changes of the alloy with different heat treatments before and after TCP process is investigated. Results show that TCP has notable effect on grain refinement and decreases crystallite size of solid solution treated aluminum 6061 material to 52. nm after equivalent strain of 3.09 which is comparable with the measured data from other SPD processes. The strength of the specimens aged before TCP is higher than that of those aged after TCP. The specimens artificially aged... 

In tube hydroforming, the inverse finite element method (IFEM) has been used for estimating the initial length of tube, axial feeding and fluid pressure. The already developed IFEM algorithm used in this work is based on the total deformation theory of plasticity. Although the nature of tube hydroforming is three-dimensional deformation, in this paper a modeling technique has been used to perform the computations in two-dimensional space. Therefore, compared with conventional forward finite element methods, the present computations are quite fast with no trial and error process. In addition, the solution provides all the components of strain. Using the forming limit diagram (FLD), the... 

In order to reach a more efficient and compact heat exchanger, it is essential to optimize the design, having in mind the impact of different geometrical parameters. Many of the previously cited studies in the area of heat transfer enhancement using vortex generators were confined only to defined points in the possible design space. Thus, a multiobjective optimization study is particularly suitable in order to cover this space entirely. A CFD simulation along with Pareto method were used to simulate the air flow and heat transfer and optimize the design parameters. The angle of attack of a pair of delta-winglets mounted behind each tube is varied between β = -90° and ß = +90°. Three... 

Shell and tube heat exchanger with single twisted tube bundle in five different twist angles, are studied using computational fluid dynamics (CFD) and compared to the conventional shell and tube heat exchanger with single segmental baffles. Effect of shell-side nozzles configurations on heat exchanger performance is studied as well. Heat transfer rate and pressure drop are the main issues investigated in the paper. The results show that, for the same shell-side flow rate, the heat transfer coefficient of heat exchanger with twisted tube bundle is lower than that of the heat exchanger with segmental baffles while shell-side pressure drop of the former is even much lower than that of the... 

Pulsating Heat Pipes are an effective mean for heat removal with the potential for a widespread application in electronic packaging. An experimental study a Closed Loop Pulsating Heat Pipe (CLPHP) constructed of copper tubes formed into four meandering turns is presented. Once configured in a vertical orientation the lower portion of the CLPHP comes in contact with a heat source (called the evaporator) from which it will remove heat through the pulsating action of the two-phase mixture contained within the initially evacuated copper tubes eventually transfer the heat to a heat sink (known as the condenser). Heat fluxes can be measured using temperature data gathered from experiments.... 

While for shallow waters the use of old offshore jackets still seems efficient and justifiable, for deep and ultra-deep waters such platforms cannot be used. During the past few decades the old generation of fixed offshore platforms was succeeded by the new floating platforms and new designs such as FPSOs. A new family of floating offshore platforms has been developed. These should be able to respond to size, weight and space for operating equipment, i.e. they can be constructed to have a wide range of load-bearing capacities. Use is made of the old concept of Life Saving Tubes, which in their simplest form can be a toroidal shaped tyre inner tube. The Torus-shaped idea can be further... 

In this paper the effect of the re-autofrettage process on the residual stress distribution at the wall of a thick-walled tube is considered. For accurate material behavior modeling, it is assumed that the yield surface is a function of all the stress invariants. Also for estimating the behavior of the material under loading-unloading process, a modified Chaboche's hardening model is applied. For evaluation of this unloading behavior model a series of loading-unloading tests are conducted on specimens that are made of the high strength steel, DIN1.6959. In addition the finite element simulations are implemented to simulate the re-autofrettage process and to estimate the residual stresses.... 

The network structure of styrene-butadiene rubber (SBR) in the presence of carbon black (CB) with two different structures and multi-walled carbon nanotubes (MWCNTs) was investigated. Swelling behaviour, tensile properties at various strain rates and cure kinetics were characterized. Experimental data were analysed using the Flory-Rehner model as well as the tube model theory. It is found that the network structure of CB-filled SBR follows a three-phase composite model including rigid particles, semi-rigid bound rubber and matrix rubber. This bound rubber is postulated to be critical for the mechanical and deformational properties, development of crosslinking density in matrix rubber and... 

In this paper, the responses of shape memory polymer (SMP) helical springs under axial force are studied both analytically and numerically. In the analytical solution, we first derive the response of a cylindrical tube under torsional loadings. This solution can be used for helical springs in which both the curvature and pitch effects are negligible. This is the case for helical springs with large ratios of the mean coil radius to the cross sectional radius (spring index) and also small pitch angles. Making use of this solution simplifies the analysis of the helical springs to that of the torsion of a straight bar with circular cross section. The 3D phenomenological constitutive model...