Sharif Digital Repository

The purpose of this thesis is to investigate and identify the performance of a class D gas turbine and improve its efficiency.This thesis contains three parts: first part is to choose a specific engine in class D, for our case “Centaur 40”, then this engine, model and validate by GASTURB with existed data.Second part is tosurvey methods of pgradedemonstrated gas turbine with regard to upgraded Solar Centaur 40 “Taurus 60” using the FORTRAN code base on Stage Stacking method.Finally,the last part of this thesis is to investigate Compressor-Turbine matching. In this part the matching zone of the original and upgraded gas turbines are determined and effect of upgrading on matching zone is... 

Today energy sources, in any kind, have their special situation in human’s life and we must use our knowledge to manage them for effective usage by decreasing losses and finding modern renewable sources. One of the best way to achieve this purpose is increasing efficiency and improve energy generator performances under different environmental conditions. In spite of the fact that wind turbines stall dynamics behavior is under investigation for 6 years, study of dynamic stall phenomenon especially over series blades still needed. By addition to this phenomenon, improper wind turbine arrange decreases efficiency too. As a matter of fact, scrutiny of dynamics stall of wind turbines serial... 

Recently, a lot of attention has been devoted to the use of Darrieus wind turbines because of high power density and environment aspect in urban areas. Turbine airflows don’t effect on the power coefficient of Darrieus turbine. This turbine has an acceptable power coefficient depend on the other wind turbine in the small scale turbine. Aerodynamic performance of a Darrieus turbine is very complex due to phenomena such as dynamic stall and changing forces on the turbine caused by changing horizontal angles. So study airflows around turbine must be preformed. In this thesis the aerodynamics of an H-rotor vertical axis wind turbine (VAWT) has been studied using computational fluid dynamics in... 

Considering the negative effects of contamination on wind turbine blade performance, we investigate aerodynamics performance of a one- Megawatt wind turbine. To achieve this, we compare the performance and power of the wind turbine with and without contaminations. To calculate the wind turbine output power, we use a developed wind turbine calculator, which benefits from the Blade Element Momentum (BEM) theory. Furthermore, the aerodynamics calculations are performed using of a commercial software for clean and rough airfoils. Considering the change of Reynolds number along the blade axis, the airfoil characteristics are calculated for two Reynolds numbers of 0.5 and 3.5 millions to increase... 

Increasingenergy requirements, limitedfossil resources, environmental pollutioncaused byfossilfuels, global warmingand other factorshaveled tothe approach ofscience and technologyfor renewable energies. One of the renewable energies is the energy relevant to ocean currents that is mainlydue to theinteractionbetween thetidalattraction ofthe moon,sun andearth. In our country,due tothehigh tideon the southern coast, there isgood potentialto use thistype of energy. One of themost favorableareasformarinecurrentpower plantslocated inthe northern part ofthe islandof Qeshmchannel.In this thesis,to exploitthis potential, the newidea ofHunter tidalturbine was investigated,because... 

Wind is one of the clean energies available in the world which its damage to the environment is less than other renewable resources. One of technologies of generating energy from wind is the small turbines installed in city area. However, installing these turbines in cities may encounter with problems such as low speed of wind and high turbulence in the air causing aero-dynamic noise. If the turbines are installed in a bad place in cities, their electricity generation might be zero. Among important parameters that affect the performance of the turbines installed in the roof is the formation of the building, the buildings around, and the location of wind turbine. If the buildings’... 

This project aims to investigate environmental effect –such as dust and rain- on the performance of a vertical axis wind turbine (VAWT). However, those issues are frequently investigated in the horizontal axis wind turbines, but this subject has not been studied in vertical axis wind turbines. Impact of rain or dust particles on the turbine blades can change the turbine performance. So consideration of the impact of environmental factors on the performance of wind turbines is very important. Vertical axis wind turbines, particularly the straight bladed VAWT are widely used in wind power generation in agricultural and rural lighting and the use of this type of turbines is increasing... 

Limited fossil resources, daily increase of demand for energy and the most important one that is environmental pollution fact, make people think of renewable energy as a solution. One type of these renewable energies is offshore wind energy that has high potential without any sound and visual noises. Recently a lot of researches have carried out their studies on the topic of offshore wind turbine. Cause of disabling of a lot of software to simulating of dynamic effect of rotating rotors, so in this research has make effort to fabricate and test an offshore wind turbine with different rotor rotating velocities and different heading angle of wind, to catch the effect of these parameter on the... 

Advanced control techniques are required to achieve a cost-effective and reliable use of the wind power generation. The wind turbines are generally controlled based on two control objectives: the turbine protection and the generation of acceptable power for the utility grid. These objectives are achieved if the control inputs are applied based on appropriate control logics. In this work, a nonlinear multivariable model of the wind turbine with a DFIG generator is considered. The rotor speed and the d-axis rotor current (as the control outputs) are controlled via manipulation of the two generator voltages (as the control inputs) in low wind velocity condition. For high wind velocity, the... 

An aerodynamical model for studying asymmetric and three-dimensional flow fields about wind turbine rotors is presented. The developed algorithm combines a asymmetric and three-dimensional Navier-Stokes solver with a so-called actuator disc technique in which the loading is distributed along lines representing the blade forces. The loading is determined iteratively using a bladeelement approach and tabulated airfoil data. Computations are carried out for a 5MW NREL wind turbine equipped with three blades. The computed power production is found to be in good agreement with measurements. The computations give detailed information about basic features of wind turbine wakes, including... 

Wastewater treatment plants play an important role within the urban water cycle in protecting receiving waters from untreated discharges. In the developed and developing countries, Energy consumption of these units are 3 and 5 % of the electrical energy demand, respectively. As far as sustainable development is concerned, not only the reduction of WWTP’s energy consumption is mandatory, but also these units should produce energy. To this end, several techniques are available namely: energy audits, replacement of equipment and improvement of process efficiency. Moreover, Energy can be generated by converting biogas -from anaerobic digesters- to heat and power. Todays, Biogas is well-known as... 

For several decades, turbocharging of internal combustion engines has been a wide spreading technology to increase the engine output power as much as possible. Turbocharger has two main components: compressor, and turbine. Therefore, increasing the efficiency of turbine and compressor has a major role in engine performance improvement. This has been a continuous research goal in 20th century. Considerable advances has been achieved until now. Turbocharger turbine should be matched to engine in a wide range operation conditions with high efficiency. Many researchers have published their achievements considering turbine elements design improvements. This research is focused on the turbine... 

The present research proposes a new method to establish a practical framework for extension of gas turbine life time. This method is based on an nine-step operational algorithm which is capable for different types of gas turbine. The essential inputs for this algorithm includes documents of inspection and knowledge of repair and maitenance experts. In this algorithm is used the Bayesian network probabilistic method. Therefore, based on the observations and the knowledge of experts, gas turbine Bayesian network is produced. According to this Bayesian network consequenses are created. Furthermore, making the steps of the algorithem more explicit, FTA and FMEA methods are used to creat the... 

Air-cooled condenser is widely used in thermal power plants as its main cooling system. However, the thermal capacity of air-cooled condensers reduces considerably in environmental wind drafts. So, the purpose of this study is to find practicable solutions to minimize the mal-performance of air-cooled condensers in windy conditions in either design or off-design conditions and consequently prevent the related steam turbines power reduction. The target combined cycle power plant consists of 4*160 MW steam turbines and 4 air-cooled condensers in its steam cycle part. This research presents two general and practical remedies, which are also applicable to many different powerplants irrespective... 

Gas turbine engine control is a demanding task that requires the regulation of the thrust as well as the satisfaction of the limitations such as engine aerodynamic instability, over temperature and over speed. Fuzzy logic is an attractive technique for the control of poor understood unmodeled, or complex systems especially where the experience of human operators is available to provide qualitative rules. In such cases, it has been found that control decisions can be made on the basis of linguistic measures or fuzzy algorithms. The controller that is designed on the basis of this theory is called fuzzy logic controller. The main objective of this thesis is hardware implementation of fuzzy... 

The interactions between jets and cross flows appear in many engineering applications (such as film cooling) and thus their study is of great importance. In film cooling, the coolant fluid is transferred from the compressor to the surface of the turbine blades via small holes. An increase of about 170⁰C of the engine working temperature increases the engine efficiency about 5%. To reach higher temperatures of the inlet air flow, one tries to have the least amount of interactions between the film cooling jets and the the cross flow. In this work, we computationally studied turbulent film cooling of a flat plate, in which we used the combined triple jet and investigated the effects of density... 

In order to reduce damage caused by power outages on rare events that lead to long-term disconnection of microgrid from utility grid, isolated mode performance of microgrids including wind and hudro turbines with energy storage systems is considered in this study. Using wind energy as a renewable resource is considered as an appropriate choice for power production in microgrids. However, the uncertainty in wind turbines power generation is something challenging. The existence of water resources near the wind farms causes a special opportunity for operation of these resources along with wind turbines. This thesis aimed at balancing energy supply and demand in island mode of microgrid,... 

According to development of industry in every field such as nanotechnology and micro electro mechanical system (MEM) fabricating of high speed machining with micro dimension has been expanded. Micro spindles are such a device which is useful in many industries such as air space and electronic field. These machines can work in high speed and production rate with vast variety of features. Their dimensions are in millimeter range. So they can manufacture miniature features. Fabricating and technical science production of a high speed micro spindle with speed of more than 100000 RPM (micro macro milling) is purpose of this project. After to literature review according to science of micro... 

Turbochargers are industrial devices that widely are used in aviation, marine and automotive industry. Manufacturing cost and technology of their components vary according to their application fields. One of the most important components of these devices is turbine wheel, which needs to be solid, strong and have a high resistance in critical extraordinary conditions. In these days, it can be seen that superalloys are used remarkably in manufacturing of turbine wheels. When this part of turbine is damaged due to some different reasons, turbine wheel must be quit of circle Process according to repair instructions. In these conditions either turbine must be repaired or replaced by a new one;...