Sharif Digital Repository

Constant volume transparent test combustion chambers are extensively used for investigating injection and fuel burning properties of various combustion engines. Their configuration depends on the engine type and the research purpose. Material of components, shape and dimensions of the chamber and its parts, ease of use, accessibility, sealing and safety of the assembly are the parameters needed to be considered in designing the test cell. This paper explains, structural design of a test combustion chamber and its optical windows using finite element analysis of ANSYS 12.0 software for bearing high pressure variations and thermal shocks of combustion. It was designed for conducting CNG direct... 

Porous PZT-PCN ceramics were fabricated with this formula, “0.8 Pb(Zr1/2Ti1/2)O3-0.2 Pb(Co1/3Nb2/3)O3”, abbreviated as “PZTPCN” by introducing Polyvinyl chloride(PVC) and stearic acid (SA) as pore forming agents (PFA) with varied percentages (5, 10 and 15 wt%). The optimum sintering procedure was designed according to the thermogravimetric analysis of pore formers. XRD and FESEM were applied to study the formed phase and the microstructure of the system. Electrical Characterization was conducted using Piezo meter. A decrease in density reduced longitudinal piezoelectric coefficient (d33) and relative dielectric constant (ε) and enhanced hydrostatic figure of merit (dhgh) of PZTPCN ceramics.... 

Abstract Porous lead zirconate titanate-lead cobalt niobate 0.8Pb(Zr1/2Ti1/2)O3-0.2Pb(Co1/3Nb2/3)O3 (PZT-PCN) piezoelectric ceramics were fabricated by introducing pore-forming agent polymethyl methacrylate (PMMA), and the effect of sintering behavior on their microstructure, dielectric, and piezoelectric properties were investigated. The optimum sintering procedure was designed according to the thermogravimetric analysis of pore former. Finally the electrical properties were measured. The porosity of PZT-PCN ceramics decreased and the grain size increased with an increase in the sintering temperature at a fixed PMMA addition. "An increase in density with sintering temperature from 1050 to... 

A multiplexing technique, which is based on duty-cycle division, is proposed. The channel multiplexing and demultiplexing are performed electrically at the single user bit rate, which is very economic. In a three-user system (3×10 Gb/s), the simulation results show that the best receiver sensitivity value achieved is -30.1 dBm with an optical signal-to-noise ratio (OSNR) of 22.3 dB, while the chromatic dispersion tolerance ranges from 192 to 280 ps/nm. Migration from 30 to 120 Gb/s is achieved with the penalty of 6.4 and 5.2 dB in the receiver sensitivity and OSNR, respectively, for the worst user  

In recent years, there has been a growing interest in the simulation and analysis of piezoelectric transducers with the he help of equivalent electrical circuit simulations (EECS). This paper has been devoted to study of such approach for two designed and fabricated ultrasonic sandwich transducers. By using analytical analysis, the dimensions of components of the two piezoelectric transducers were determined for the assumed resonance frequencies of 30 kHz and 40 kHz. Then, by using a two dimensional finite element model, and regarding two different modeling techniques for the transducers and by application of a current source which was connected directly to the piezoelectric pieces of the... 

Comparison of the traditional linear heating method of TPD with an original stepwise heating scheme was reported for the first time. Stepwise heating TPD was carried out by keeping the temperature constant as soon as ammonia desorption signal rises until the signal returns to the baseline. More ammonia desorption peaks on a SAPO-34 catalyst were identified using TPD with stepwise heating. The effect of temperature ramp on desorption peak broadening in TPD curve was also addressed. The more distinct ammonia desorption peaks in stepwise TPD indicates that ammonia adsorbs in about five or six different ways on SAPO-34, and attribution of different adsorptions may be explained considering some... 

Most part of Iran is dominated by arid and semi-arid areas due to low annual rainfall. The need for production of fresh water from brackish water is considerably high, especially in dry regions. In this study 1 month daily-based experimental data from a solar still site has been reported. The technical and operational problems of this site which finally contributed to the total cease of the site are described. Then a detailed analysis is investigated on progress of a prototype which constructed in order to solve the site's problems. The results of 1 month of experimental data of the final design showed that the last prototype could be used to solve the current problems of the site. The... 

Hydrocracking is one of the most versatile petroleum refining processes for production of valuable products including gasoline, gas oil, and jet fuel. In this paper, a five-parameter continuous lumping model was used for kinetic modeling of hydrocracking of vacuum gas oil (VGO). The model parameters were estimated from industrial data obtained from a fixed bed reactor operating at an average temperature of 400°C and residence time of 0.3 h. Product distributions were obtained in terms of the weight fraction of various boiling point cuts. The model parameters were estimated using the Nelder-Mead optimization procedure and were correlated with temperature. Comparison of experimental and... 

Purpose - The purpose of this paper is to present an improved methodology for design of custom-made hip prostheses, through integration of advanced image processing, computer aided design (CAD) and additive manufacturing (AM) technologies. Design/methodology/approach - The proposed methodology for design of custom-made hip prostheses is based on an independent design criterion for each of the intra-medullary and extra-medullary portions of the prosthesis. The intra-medullar part of the prosthesis is designed using a more accurate and detailed description of the 3D geometry of the femoral intra-medullary cavity, including the septum calcar ridge, so that an improved fill and fit performance... 

In this letter, we propose a method for real-time high density impulse noise suppression from images. In our method, we first apply an impulse detector to identify the corrupted pixels and then employ an innovative weighted-average filter to restore them. The filter takes the nearest neighboring interpolated image as the initial image and computes the weights according to the relative positions of the corrupted and uncorrupted pixels. Experimental results show that the proposed method outperforms the best existing methods in both PSNR measure and visual quality and is quite suitable for real-time applications  

The disposal of used tires is a major environmental problem. With increasing interest on recovery of wastes, pyrolysis is considered as an alternative process for recovering some of the value in scrap tires. An accurate kinetic model is required to predict product yields during thermal or catalytic pyrolysis of scrap tires. Pyrolysis products contain a variety of hydrocarbons over a wide boiling range. A common approach for kinetic modeling of such complex systems is lumping where each lump is defined by a boiling point range. Available experimental data for thermal and catalytic pyrolysis of scrap tires from the literature were used to evaluate two types of lumping models; discrete and... 

Compared with flat linear structures, tubular linear machines do not face edge effects, making their performance better than their flat counterparts. In this article, a novel linear variable-reluctance resolver with tubular configuration is proposed. To optimize the design of an electromagnetic structure, modeling methods are used. Thus, in this article, an analytical model for the proposed resolver is presented. This model is based on the magnetic equivalent circuit (MEC) method and is considerably less time-consuming than finite element analysis (FEA), yet provides accurate results. A conformal mapping is employed to compute the permeance of the air-gap. The proposed model is then utilized... 

In Brukner and Zeilinger's interpretation of quantum mechanics, information is introduced as the most fundamental notion and the finiteness of information is considered as an essential feature of quantum systems. They also define a new measure of information which is inherently different from the Shannon information and try to show that the latter is not useful in defining the information content in a quantum object. Here, we show that there are serious problems in their approach which make their efforts unsatisfactory. The finiteness of information does not explain how objective results appear in experiments and what an instantaneous change in the so-called information vector (or catalog of... 

Low silicon content SAPO-34 was successfully synthesized using the conventional hydrothermal crystallization in the static condition. Effects of different synthesis conditions including crystallization temperature and the silicon source were investigated through X-ray diffraction patterns. It was concluded that the silicon source had a significant effect on silicon incorporation into the alumino-phosphate building blocks in the course of crystallization. Using precipitated silica instead of silica sol resulted in the formation of impurities of alumino-phosphates phases whose crystalline structures collapse at the high temperature of calcination. For the low silicon SAPO-34 synthesis, the... 

Let R be a left Noetherian ring and ZD(R) be the set of all zero-divisors of R. In this paper, it is shown that if RZD(R) is finite, then R is finite  

Numerous methods for direction of arrival (DOA) estimation, used in smart antennas have been already reported in previous studies. The precision of DOA estimation depends on the choice of the algorithm and the geometrical configuration of the antenna array. In this work, the performance of new geometrical configurations, i.e. 2D with equal area and 3D with equal volume including circular, square, triangular, hexagonal and star geometries, with equal number of antenna elements, are examined and compared to each other to find the most proper geometry. Monte-Carlo simulations are performed to evaluate the DOA precision of the proposed arrays using the MUSIC algorithm. It is shown that in three...