Sharif Digital Repository

The aim of this research is bonding of three-layered St/AZ31/St composite by roll-bonding process. The roll-bonding process was performed at three preheating temperatures, 340, 400 and 450°C, with thickness reduction of 30 to 68% and different thicknesses of intermediate layer (AZ31). In order to improve the bonding strength, the as-rolled specimens were annealed at constant temperature of 375°C. For evaluation of bond strength and investigating the formation of a diffusion layer, the results of peel test and microscopic images were studied. Tensile specimens were prepared along the rolling direction to measure the mechanical properties of the composite. The results showed that by increasing... 

A hot gas generator is a compact heat exchanger that produces high temperature or enthalpy gases. This paper presents two methods for controlling the system. The first one is an adaptive sliding mode controller that is a Lyapunov based method and proposed to confront the dynamic modeling deficiencies and system uncertainties. The second one is a linear adaptive controller that gives a new attractive ability to the system which can track a complicated requested path. Each of the presented controllers has some capabilities that may be preferred to other. In this paper, these methods are extensively compared by several transient inputs. On the other hand, since heat exchangers are typically... 

We use the Fokker-Planck equation and its moment equations to study the collective behavior of interacting particles in unsteady one-dimensional flows. Particles interact according to a longrange attractive and a short-range repulsive potential field known as Morse potential. We assume Stokesian drag force between particles and their carrier fluid and find analytic single-peaked traveling solutions for the spatial density of particles in the catastrophic phase. In steady flow conditions the streaming velocity of particles is identical to their carrier fluid, but we show that particle streaming is asynchronous with an unsteady carrier fluid. Using linear perturbation analysis, the stability... 

Thermo mechanical processing and controlled rolling of microalloyed steel sheets are affected by several factors. In this investigation, finishing temperature of rolling which is considered as the most effective parameters on the final mechanical properties of hot rolled products has been studied. For this purpose, three different finishing temperatures of 950, 900 and 850 °C below the non-recrystallization temperature and one temperature of 800 °C in the intercritical range were chosen. It is observed that decreasing the finishing temperature causes increase of strength and decrease of total elongation. This is accompanied by more grain refinement of microstructure and the morphology was... 

This paper investigates a predictive control strategy for a single-phase PFC rectifier exploiting the Sheppard-Taylor converter. By using this converter, the detuning problem occurring in conventional PFC rectifiers, especially at low input voltages, is avoided. This paper addresses a predictive method for designing the current controller of the Sheppard-Taylor PFC converter. The control law is derived for an ideal circuit as well as a more accurate model of the converter including parasitic elements. Input voltage feed-forward compensation provides sinusoidal input current and a desired output voltage even if the input voltage is distorted. To investigate the dynamic performance of the PFC... 

The load current of three level/phase neutral point clamped rectifier could be expressed in two forms: the load current involving the current of capacitor C1, and the load current involving the current of capacitor C2. Using the Euler-Lagrange model based on the superposition law and the obtained load current, a new dual Lagrangian model of the rectifier is founded in this paper and then the two obtained nonlinear state space models are developed in dq0 reference frame. According to the new model, two positive definite Lyapunov function candidates are defined and a Lyapunov-based control is applied to the rectifier. Each of the function is utilized to control its corresponding output voltage... 

Transformation-induced plasticity (TRIP) steel resistance spot welds are delicate to low-energy interfacial failure via crack propagation through martensitic fusion zone during cross-tension (CT) loading. This paper addresses the effect of three different types of in situ postweld heat treatment (PWHT) on the mechanical properties of TRIP steel resistance spot welds. Depending on the post weld second pulse current level, three different strengthening mechanisms were found including (i) martensite tempering with reduced hardness, (ii) refining of martensite packets with improved toughness and (iii) nugget re-melting/enlargement combined with possible reduction of grain boundary impurity... 

We report the existence of interfacial instability in the two-dimensional channel flow of a sediment suspension whose particles diffuse in the carrier fluid due to shear-induced collisions. We derive partial differential equations that govern the deformations of the interface between the sediment suspension and the clear fluid, and devise a perturbation method that preserves the positivity of the particle volume fraction. We solve perturbed momentum, particle transport and deforming interface equations to show that a Kelvin-Helmholtz-type unstable wave develops at the interface for wavelengths longer than a critical value. Short-wavelength oscillations of the interface are damped due to... 

This paper attempts to study the demand function of natural gas in Iran using smooth transition regression model (STR). To this end, gross domestic productions (GDP), real price of natural gas and temperature have been employed as variables explaining the natural gas demand from 1971 to 2009. The results indicate that natural gas demand follows an LSTR1 nonlinear two-regime model if the real price of natural gas is considered as the transition variable. Estimation results also indicate that the slope parameter approximately equals the high value of 10 and the threshold value is 31.82. Rials. 111 USD=24,700 Rials (IRR) at April 2013. per one cubic meter consumption of natural gas. The results... 

Elastomeric bearings are becoming a preferred device for isolating bridges, buildings, and sensitive equipment structures. The technical specifications used to procure these isolators are considered as important factors for the consumers. Lack of communication between structural engineers and rubber technologists, causes structural engineers have slight understanding of rubber properties. In the present study, a number of compounds were initially designed and manufactured, based on a previously studied and manufactured isolator compound. The outcome of the experiments indicated the physical and mechanical properties. Afterwards, the targeted improvement led to modification of the compounds... 

In this work, the formability of a hybrid material of Interstitial-Free 240 (IF240) steel and AZ31 magnesium alloy as IF240/AZ31/IF240 tri-layered sheets was investigated. For this purpose, the bonding feasibility of the high-formability IF240 steel and low-formability AZ31 sheets was first assessed. Then, the hot formability behavior of the manufactured laminated composite was evaluated. The rolling of the preheated samples established the layer bonding. The bonding strength was determined using the shear punch test. The texture and its effects on the forming behavior were studied using the x-ray Goniometry method. Nakazima dome tests were employed at ambient and elevated temperatures to... 

In this work, the formability of a hybrid material of Interstitial-Free 240 (IF240) steel and AZ31 magnesium alloy as IF240/AZ31/IF240 tri-layered sheets was investigated. For this purpose, the bonding feasibility of the high-formability IF240 steel and low-formability AZ31 sheets was first assessed. Then, the hot formability behavior of the manufactured laminated composite was evaluated. The rolling of the preheated samples established the layer bonding. The bonding strength was determined using the shear punch test. The texture and its effects on the forming behavior were studied using the x-ray Goniometry method. Nakazima dome tests were employed at ambient and elevated temperatures to... 

The increasing use of multi-party web conferencing applications demands for suitable multicast protocols. Limited bandwidth of typical internet user requires the underlying multicast routing to be efficient. In this paper we present HOMA; an application layer multicast protocol which has been tailored for small-scale multi-party videoconferencing applications. Considering the requirements of such applications, HOMA uses a heuristic routing to construct efficient multicast trees on the application layer. We have evaluated the performance of the proposed routing algorithm through simulations. Experimental results indicate that the proposed algorithm performs better than the related algorithms... 

The effect of pulsed direct current (PDC) on solid-state diffusion in the Ni–Al binary system was investigated. Two experimental schemes were employed: in the presence and absence of an electric field. The diffusion couples were heat-treated for 1.5, 3, and 5 h at 803, 833, and 863 K. Under the investigated conditions, only two intermetallic phases (NiAl3 and Ni2Al3) formed at the boundary of the metals. It was shown that the PDC passing through the diffusion couple significantly enhanced the growth rates of both phases. The apparent reaction–diffusion coefficients were DNiAl3=4.0×10−9exp(−[Formula presented]) and DNi2Al3=9.7×10−9exp(−[Formula presented]) in the field-assisted scheme,... 

The nanocomposite Cu–Cr powder was consolidated by flash spark plasma sintering (FSPS), which involves applying an extremely rapid change in the electrical power passing through the bulk of the sample. It was demonstrated that an essentially fully dense material could be obtained in 15 s. Such short-term treatment typically preserves the nanostructured features of the material. However, investigation revealed a nonuniformity in the microstructure of the alloys obtained under such extreme conditions. To better understand the observed effects, the FSPS process was simulated. It was observed that a rapid change in the applied electrical power resulted in nonuniform distributions of current... 

Resistance spot welding was used to join austenitic stainless steel and galvanized low carbon steel. The relationship between failure mode and weld fusion zone characteristics (size and microstructure) was studied. It was found that spot weld strength in the pullout failure mode is controlled by the strength and fusion zone size of the galvanized steel side. The hardness of the fusion zone which is governed by the dilution between two base metals, and fusion zone size of galvanized carbon steel side are dominant factors in determining the failure mode. © 2007 Elsevier B.V. All rights reserved  

Several carbon capture techniques have been developed in response to the notable rise of atmospheric carbon dioxide (CO2) levels. The utilization of diethanolamine (DEA) as an absorption method is prevalent in various industries due to its high reactivity and cost-efficiency. Hence, comprehending the equilibrium solubility of CO2 in DEA solutions is an essential step in developing and optimizing absorption procedures. In order to predict the CO2 loading capacity in the DEA solutions, four advanced deep learning and machine learning models were developed: recurrent neural networks (RNN), deep neural networks (DNN), random forest (RF), and adaBoost-support vector regression (AdaBoost-SVR). The... 

Accurate prediction of the solubility of gases in hydrocarbons is a crucial factor in designing enhanced oil recovery (EOR) operations by gas injection as well as separation, and chemical reaction processes in a petroleum refinery. In this work, nitrogen (N2) solubility in normal alkanes as the major constituents of crude oil was modeled using five representative machine learning (ML) models namely gradient boosting with categorical features support (CatBoost), random forest, light gradient boosting machine (LightGBM), k-nearest neighbors (k-NN), and extreme gradient boosting (XGBoost). A large solubility databank containing 1982 data points was utilized to establish the models for... 

In this paper the question of the emission of fermions in the process of dilaton black hole evolution and its characteristics for different dilaton coupling constants α are studied. The main quantity of interest, the greybody factors, are calculated both numerically and in analytical approximation. The dependence of the rates of evaporation and behaviour on the dilaton coupling constant is analysed. Having calculated the greybody factors, we are able to address the question of the final fate of the dilaton black hole. For that we also need to perform dynamical treatment of the solution by considering the backreaction, which will show a crucial effect on the final result. We find a transition... 

In pebble bed reactors, the core is filled with thousands of graphite and fuel pebbles. Fuel pebbles in these reactors consist of TRISO particles, which are embedded in a graphite matrix stochastically. The reactor core is also stochastically filled with pebbles. These two stochastic geometries comprise the so-called double heterogeneous nature of this type of reactor. In this paper, a pebble bed reactor, the HTR-10, is used to demonstrate a treatment of this double heterogeneity using the MCNP5 Monte Carlo code and MATLAB programming. In this technique, TRISO particles are modeled in a pebble using the expanded FILL and LATTICE features of MCNP5. MATLAB is used to generate random numbers...