Sharif Digital Repository

In this paper, an industrial ethylbenzene production unit has been simulated and the results are compared against five-day experimental data. According to prevailing unit condition, i.e. recycled ratio of benzene, benzene selectivity, and energy consumption, the unit is not working under its optimum conditions for minimum cost of ethylbenzene production. In the current design, high amount of benzene recycle (6:1) causes to have an additional cost due to fractionation of ethylbenzene from benzene. A new approach is proposed to modify the benzene alkylation process and reduce the unit's energy consumption. In the newly designed scheme, two double-bed alkylation reactors converted into four... 

Industrial wastewaters are different from sanitary wastewaters, and treatment complications due to their unique characteristics, so biological processes are typically disrupted. High chemical oxygen demand, dye, heavy metals, toxic organic and non-biodegradable compounds present in petroleum industry wastewater. This study intends to optimize the photocatalytic proxone process, utilizing a synthesized ZnO–Fe3O4 nanocatalyst, for petroleum wastewater treatment. The synthesis of ZnO–Fe3O4 was done by air oxidation and layer-by-layer self-assembly method and XRD, SEM, EDAX, FT-IR, BET, DRS, and VSM techniques were used to characterize the catalyst. Central composite design (CCD) method applied... 

Biomechanical modeling approaches require body posture to evaluate the risk of spine injury during manual material handling. The procedure to measure body posture via motion-analysis techniques as well as the subsequent calculations of lumbosacral moments and spine loads by, respectively, inverse-dynamic and musculoskeletal models are complex and time-consuming. We aim to develop easy-to-use yet accurate artificial neural networks (ANNs) that predict 3D whole-body posture (ANNposture), segmental orientations (ANNangle), and lumbosacral moments (ANNmoment) based on our measurements during load-handling activities. Fifteen individuals each performed 135 load-handling activities by reaching (0... 

The vision of advanced long-term evolution (LTE-A) project is set to ultimate increase of network capacity in heterogeneous networks (HetNets). In HetNets with small cell configuration, a considerable majority of user devices is eventually connected to the macrocell base station (MBS), while small base stations (BSs), such as femtocell access points (FAPs), are still without any user. This results in unbalanced load and reduces the data rate of macrocell user equipment (MUE). In this paper, a method is proposed for load balancing among FAPs, while desired throughput is achieved. The proposed method uses the estimated received signal strength from different BSs and adjusted pilot signals.... 

Long-term electricity load and price forecasts have become critical inputs to energy service provider (ESP) decision makings in restructured environments. This paper presents a three-stage hierarchical approach for long-term electricity load forecasting. These stages are called yearly trend model (YTM), weekly trend model (WTM), and daily trend model (DTM). The first stage fits an appropriate function to data and extracts its yearly trend. The weekly and daily trends are then extracted using the Box-Jenkins method in WTM and DTM, respectively. For doing so, candidate trends are identified using auto correlation function (ACF) and partial auto correlation function (PACF) plots. Then, Akaike... 

Background: Allergic contact dermatitis is a common disorder in adults and children alike and appears to be on the increase. The purpose of this study was to determine the sensitization trends in Iranian children with contact dermatitis. Methods: The result of 109 patch tests performed using the 24 allergens of the European Standard Series in patients below 18 years old from September 2007 to March 2009 were recorded and analyzed. The tests were evaluated at 48 and 72 h after performing. Results: The study population consisted of 72 (66.1 %) females and 37 (33.9 %) males. Hands were the most commonly affected anatomic site. In the final evaluation of the tests on day three, 51 (46.8 %)... 

Chinese hamster ovary cells are the main cellular factories for production of a wide range of recombinant proteins in biopharmaceutical industry. Recombinant human Interferon beta-1a (rh-IFN β-1a), as a cytokine is broadly used to treat multiple sclerosis. In this work, the cell line producing rh-IFN β-1a was studied to improve cell density along with the specific expression. For this reason different cell culture experiments were done using different commercial serum-free media to find the appropriate media providing higher cell density. It was shown DMEMF12, DMEM:ProCHO5, and CHO-S-SFM II led to higher cell density and shorter doubling time. Next, using these media, fed-batch, and... 

Comparison of the traditional linear heating method of TPD with an original stepwise heating scheme was reported for the first time. Stepwise heating TPD was carried out by keeping the temperature constant as soon as ammonia desorption signal rises until the signal returns to the baseline. More ammonia desorption peaks on a SAPO-34 catalyst were identified using TPD with stepwise heating. The effect of temperature ramp on desorption peak broadening in TPD curve was also addressed. The more distinct ammonia desorption peaks in stepwise TPD indicates that ammonia adsorbs in about five or six different ways on SAPO-34, and attribution of different adsorptions may be explained considering some... 

Most part of Iran is dominated by arid and semi-arid areas due to low annual rainfall. The need for production of fresh water from brackish water is considerably high, especially in dry regions. In this study 1 month daily-based experimental data from a solar still site has been reported. The technical and operational problems of this site which finally contributed to the total cease of the site are described. Then a detailed analysis is investigated on progress of a prototype which constructed in order to solve the site's problems. The results of 1 month of experimental data of the final design showed that the last prototype could be used to solve the current problems of the site. The... 

Hydrocracking is one of the most versatile petroleum refining processes for production of valuable products including gasoline, gas oil, and jet fuel. In this paper, a five-parameter continuous lumping model was used for kinetic modeling of hydrocracking of vacuum gas oil (VGO). The model parameters were estimated from industrial data obtained from a fixed bed reactor operating at an average temperature of 400°C and residence time of 0.3 h. Product distributions were obtained in terms of the weight fraction of various boiling point cuts. The model parameters were estimated using the Nelder-Mead optimization procedure and were correlated with temperature. Comparison of experimental and... 

Purpose - The purpose of this paper is to present an improved methodology for design of custom-made hip prostheses, through integration of advanced image processing, computer aided design (CAD) and additive manufacturing (AM) technologies. Design/methodology/approach - The proposed methodology for design of custom-made hip prostheses is based on an independent design criterion for each of the intra-medullary and extra-medullary portions of the prosthesis. The intra-medullar part of the prosthesis is designed using a more accurate and detailed description of the 3D geometry of the femoral intra-medullary cavity, including the septum calcar ridge, so that an improved fill and fit performance... 

In this letter, we propose a method for real-time high density impulse noise suppression from images. In our method, we first apply an impulse detector to identify the corrupted pixels and then employ an innovative weighted-average filter to restore them. The filter takes the nearest neighboring interpolated image as the initial image and computes the weights according to the relative positions of the corrupted and uncorrupted pixels. Experimental results show that the proposed method outperforms the best existing methods in both PSNR measure and visual quality and is quite suitable for real-time applications  

The disposal of used tires is a major environmental problem. With increasing interest on recovery of wastes, pyrolysis is considered as an alternative process for recovering some of the value in scrap tires. An accurate kinetic model is required to predict product yields during thermal or catalytic pyrolysis of scrap tires. Pyrolysis products contain a variety of hydrocarbons over a wide boiling range. A common approach for kinetic modeling of such complex systems is lumping where each lump is defined by a boiling point range. Available experimental data for thermal and catalytic pyrolysis of scrap tires from the literature were used to evaluate two types of lumping models; discrete and... 

Compared with flat linear structures, tubular linear machines do not face edge effects, making their performance better than their flat counterparts. In this article, a novel linear variable-reluctance resolver with tubular configuration is proposed. To optimize the design of an electromagnetic structure, modeling methods are used. Thus, in this article, an analytical model for the proposed resolver is presented. This model is based on the magnetic equivalent circuit (MEC) method and is considerably less time-consuming than finite element analysis (FEA), yet provides accurate results. A conformal mapping is employed to compute the permeance of the air-gap. The proposed model is then utilized...