Sharif Digital Repository

A hot filament chemical vapor deposition (HFCVD) method was used to prepare Fe-Cr thin film on Si substrate. The produced layers were used as catalysts for growing carbon nanotubes (CNTs) from liquid petroleum gas (LPG) at 825 °C by thermal CVD (TCVD) method. To characterize the obtained catalysts or CNTs, X-ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and Raman spectroscopy were used. CNTs were grown on HFCVD derived Fe-Cr catalyst with the LPG as carbon source successfully. It was found that an annealing process on catalysts enhances the surface concentration of Cr atoms and reduces the sizes of catalyst particles. The... 

In this study a hot filament chemical vapour deposition (HFCVD) technique was used to prepare Fe-Cr films on Si substrate as catalysts for thermal CVD (TCVD) growing of carbon nanotubes (CNTs) from liquid petroleum gas (LPG) at 800 °C. To characterize the catalysts or CNTs, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy were used. The XPS spectra obtained at different stages of Ar+ sputtering revealed that in the depth of catalyst layers, the relative Fe-Cr concentrations are higher than the top-surface. SEM images of samples after TCVD indicate a significant CNT growing at the backside of catalyst... 

Gold nanoparticles (Au NPs) were synthesized by co-deposition of RF-sputtering and RF-PECVD from acetylene gas and Au target on the carbon nanotubes (CNTs). The CNTs were prepared by thermal chemical vapor deposition (TCVD) and Pd nanoparticles catalyst. TEM image shows that high-density and uniform distribution of Au NPs were grown on the CNTs. XRD analysis indicates that Au NPs have fcc crystal structure and CNTs have a good graphite structure. Raman spectroscopy results suggest that our sample includes double-walled CNTs. It is resulted that intensity of D-band reduces and G-band intensity raises and radial breathing mode (RBM) is changed by immobilizing of Au NPs on the CNTs. Raman... 

In real-time packet-based communication systems, one major problem is misrouted or delayed packets which results in degraded perceived voice quality. If packets are not available on time, the packet is known as lost packet. The easiest task of a network terminal receiver is to replace silence for the duration of lost speech segments. In a high quality communication system, to avoid quality reduction due to packet loss, a suitable method and/or algorithm is needed to replace the missing segments of speech. In this paper, we introduce a low order recursive linear prediction method for replacement of lost speech segment. In this method a normalized least mean square (NLMS) as an adaptive filter... 

TCVD growth of multiwalled carbon nanotubes (MWCNTs) was reported by catalytic decomposition of liquefied petroleum gas (LPG) at a temperature range of 580800 °C. Laser ablation was employed as a simple and rapid technique to produce Pd nanoparticles which possess effective catalytic activities for CNT synthesis. UVvisible spectroscopy and TEM images confirmed that the Pd nanoparticles are stable for a long time and have rather spherical shape with average size of 7 nm. SEM and TEM observations and Raman spectroscopy demonstrated that the CNTs have a wavy structure, dense morphology and acceptable crystallinity. Since Pd nanoparticles are inactivated or agglomerated at extremes of the... 

Ni-Si mixed oxide nanocomposite was prepared by co-precipitation method with Ni(NO 3) 2 ·6H 2O and tetraethylorthosilicate (TEOS) at pH = 10.5 under reflux condition for 6 days. It was then used as a catalyst for the formation of carbon nanotubes (CNTs) by CVD procedure. Characterization of the catalyst and the CNTs was carried out using X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. The results showed that Ni-Si mixed oxides nanorods with the average diameter of 3 to 4 nm play a key role in CNTs formation  

In this work, hot tension tests were conducted on as cast and wrought samples of a high carbon high chromium tool steel to study the hot workability under the rolling conditions. The flow curves illustrate the classical shape of dynamic recrystallization (DRX). It is observed that broken carbide nets in the wrought samples result in lower deformation activation energy 398. kJ/mol in comparison to the as cast samples 432. kJ/mol. Necking strains were calculated using the inflection point of the work-hardening (θ) vs. stress curves. Wrought samples show higher hot ductility and lower maximum stress than the as cast ones. It is shown that lower activation energy of deformation and lower stress... 

In this research a computer model based on elasto hydrodynamic fluid film lubrication is developed in order to calculate the torque transmission efficiency of a half-toroidal CVT variator. Validation of this model is verified by comparing the experimental and the model results. Sensitivity of torque transmission efficiency to eleven parameters is investigated. These parameters are: dimensionless roller curvature, aspect ratio, half cone angle, fluid viscosity index, pressure constant for Roelands model, input rotational velocity, absolute viscosity at atmospheric pressure, Young modulus of disks and power rollers, Poisson ratio of disks and power rollers, number of power rollers and variator... 

In this research a model is developed which calculates the torque transmission efficiency of a half-toroidal CVT as a function of variator geometry, gear ratio and input torque. The different criteria which are considered to be important in a half toroidal CVT performance are torque transmission efficiency, variator weight, roller fatigue life and bearing torque loss. Variation of geometrical characteristics such as roller curvature, number of power rollers, aspect ratio and half cone angle affect these criteria in different ways. Therefore, in order to find the optimal quantity for each geometrical parameter an optimization problem should be developed. The objective function of this...