Sharif Digital Repository

In recent years, there has been a growing interest in the simulation and analysis of piezoelectric transducers with the he help of equivalent electrical circuit simulations (EECS). This paper has been devoted to study of such approach for two designed and fabricated ultrasonic sandwich transducers. By using analytical analysis, the dimensions of components of the two piezoelectric transducers were determined for the assumed resonance frequencies of 30 kHz and 40 kHz. Then, by using a two dimensional finite element model, and regarding two different modeling techniques for the transducers and by application of a current source which was connected directly to the piezoelectric pieces of the... 

Constant volume transparent test combustion chambers are extensively used for investigating injection and fuel burning properties of various combustion engines. Their configuration depends on the engine type and the research purpose. Material of components, shape and dimensions of the chamber and its parts, ease of use, accessibility, sealing and safety of the assembly are the parameters needed to be considered in designing the test cell. This paper explains, structural design of a test combustion chamber and its optical windows using finite element analysis of ANSYS 12.0 software for bearing high pressure variations and thermal shocks of combustion. It was designed for conducting CNG direct... 

Porous PZT-PCN ceramics were fabricated with this formula, “0.8 Pb(Zr1/2Ti1/2)O3-0.2 Pb(Co1/3Nb2/3)O3”, abbreviated as “PZTPCN” by introducing Polyvinyl chloride(PVC) and stearic acid (SA) as pore forming agents (PFA) with varied percentages (5, 10 and 15 wt%). The optimum sintering procedure was designed according to the thermogravimetric analysis of pore formers. XRD and FESEM were applied to study the formed phase and the microstructure of the system. Electrical Characterization was conducted using Piezo meter. A decrease in density reduced longitudinal piezoelectric coefficient (d33) and relative dielectric constant (ε) and enhanced hydrostatic figure of merit (dhgh) of PZTPCN ceramics.... 

Abstract Porous lead zirconate titanate-lead cobalt niobate 0.8Pb(Zr1/2Ti1/2)O3-0.2Pb(Co1/3Nb2/3)O3 (PZT-PCN) piezoelectric ceramics were fabricated by introducing pore-forming agent polymethyl methacrylate (PMMA), and the effect of sintering behavior on their microstructure, dielectric, and piezoelectric properties were investigated. The optimum sintering procedure was designed according to the thermogravimetric analysis of pore former. Finally the electrical properties were measured. The porosity of PZT-PCN ceramics decreased and the grain size increased with an increase in the sintering temperature at a fixed PMMA addition. "An increase in density with sintering temperature from 1050 to... 

Herein, in a one-pot method, the reduced graphene oxide layers with the assistance of multiwalled carbon nanotubes were decorated to provide a suitable space for the in situ growth of CoNi2S4, and the porphyrins were incorporated into the layers as well to increase the sensitivity of the prepared nanostructure. The prepared nanocomposite can establish π–π interactions between the genetic material and on the surface of porphyrin rings. Also, hydrogen bonds between genetic domains and the porphyrin’ nitrogen and the surface hydroxyl groups are probable. Furthermore, the potential donor–acceptor relationship between the d7 transition metal, cobalt, and the genetic material provides a suitable... 

Malaysian secondary schools are facing a shortage of male teachers. Almost 70% of the teaching profession is dominated by female teachers. There is an obvious gap in the reason why teaching is not preferred by the male gender. This study intends to find the determinants of career success among male teachers with the hope of revealing the career success factors that are associated with male teachers. A survey was done among 140 male teachers in secondary schools in the state of Malacca, Malaysia. Results showed that 4out of 5 of the determinants factors are significantly explaining career success among the teachers (Emotional Intelligence, Person-Job-Fit, Career Adaptability & Work-Life... 

A multiplexing technique, which is based on duty-cycle division, is proposed. The channel multiplexing and demultiplexing are performed electrically at the single user bit rate, which is very economic. In a three-user system (3×10 Gb/s), the simulation results show that the best receiver sensitivity value achieved is -30.1 dBm with an optical signal-to-noise ratio (OSNR) of 22.3 dB, while the chromatic dispersion tolerance ranges from 192 to 280 ps/nm. Migration from 30 to 120 Gb/s is achieved with the penalty of 6.4 and 5.2 dB in the receiver sensitivity and OSNR, respectively, for the worst user  

Background: Diesel mainly consists of paraffin and thio-aromatic compounds. Sulfur present in diesel exhaust is the major challenge for oil refineries. Sulfur is an oxidizing element that discharges as acute pollutant in the environment, having adverse effects on human and animal life. Introduction: The scope of this review paper is to discuss and highlight the recent advancements in the process of desulfurization of diesel oil to explore the less energy-intensive and more economical process. Methods: Recently, different techniques are widely used for desulfurization of diesel oil to remove sulfur containing compounds from diesel. These techniques mainly involve hydrodesulfurzation,... 

Background: Water contamination by noxious heavy metals due to urbanization is a global environmental problem. Heavy metal ions pollution makes the water unsuitable for drinking and is also highly toxic to human beings and eco-system. The remediation of heavy metals is therefore very crucial. Methods: Adsorbents based on biopolymer and eco-friendly polymer composites have been developed and fabricated to remediate and remove heavy metals from the ecosystem. Results: In recent years biocomposites have been successful as cost-effective adsorbents for the remediation of various contaminants with their eco-friendly nature and sustainability. Conclusion: This review article gives an overview on... 

Hybrid bioactive inorganic-organic carbon-based nanocomposites of reduced graphene oxide (rGO) nanosheets enlarged with multi-walled carbon nanotubes (MWCNTs) were decorated to provide a suitable space forin situgrowth of CoNi2S4and green-synthesized ZnO nanoparticles. The ensuing nanocarrier supplied π-π interactions between the DOX drug and a stabilizing agent derived from leaf extracts on the surface of ZnO nanoparticles and hydrogen bonds; gene delivery of (p)CRISPR was also facilitated by chitosan and alginate renewable macromolecules. Also, these polymers can inhibit the potential interactions between the inorganic parts and cellular membranes to reduce the potential cytotoxicity.... 

The nanotubular arrays of titanium dioxide (TiO2 NTs) have recently received considerable interest for fabrication of dental and orthopedic implants. However, their antibacterial activity requires substantial improvement for the potential infections minimization, without compromise of their biocompatibility. In this work, TiO2 NTs were developed on Ti6Al4V substrates via anodization at a constant potential of 60 V for 60 min, followed by heat treatment at 500 °C for 90 min. Physical vapor deposition (PVD) was further employed to decorate silver oxide nanoparticles (Ag2O NPs) on the nanotubular edges. The results indicated that the highly-ordered TiO2 NTs with decorated Ag2O NPs could promote...