Loading...
Search for: alizadeh-bayati--zeynab
0.123 seconds

    Design and Development of Gamma Wireless Detector with the Use of Soft Computing to Identify the Type of Radioisotope for Environmental Monitoring

    , M.Sc. Thesis Sharif University of Technology Alizadeh Bayati, Zeynab (Author) ; Vosoughi, Naser (Supervisor) ; Moshkbar Bakhshayesh, Khalil (Co-Supervisor)
    Abstract
    The inability to directly observe radioactive rays, from the beginning of the discovery of these rays, led various people to seek a suitable solution to detect and recognize their properties. To this end, many detectors with different capabilities were built. On the other hand, in the electronic world, it was possible to analyze electrical pulses and extract information based on them. Therefore, some detectors were designed to convert the traces left by the entry and interaction of radioactive rays into measurable electrical pulses proportional to the properties of the incident radiation. Analysis of these pulses provides information about the properties of the incident rays. So far, a... 

    Design, Simulation and Fabrication of Thz Absorber for Thermal Superconducting Detector

    , M.Sc. Thesis Sharif University of Technology Zeynab, Alipour Gougeh (Author) ; Fardmanesh, Mehdi (Supervisor)
    Abstract
    At almost all frequencies, we have good methods to generate and detect electromagnetic radiations. One crucial exception is the low terahertz range,where despite intensive research there is a severe lack of proper devices for many applications in this frequency range such as oscillators and detectors that is so-called THz gap and includes 0.3 to 10 THz spectrum. There are different types of THz detectors but bandwidth of dection of most of them is narrow. Among these detectors, superconducting transition edge balometer detector has detectivity in wide frequency range. But generally, detectivity of these detectors strongly depends on their ability to absorb radiations of electromagnetic waves... 

    Effect of electrical parameters on morphology, chemical composition, and photoactivity of the nano-porous titania layers synthesized by pulse-microarc oxidation

    , Article Electrochimica Acta ; Volume 55, Issue 8 , 2010 , Pages 2760-2766 ; 00134686 (ISSN) Bayati, M. R ; Moshfegh, A. Z ; Golestani Fard, F
    2010
    Abstract
    TiO2 layers were grown via pulse type microarc oxidation process under different applied voltages, frequencies, and duty cycles. Surface chemical composition and phase structure of the synthesized layers were studied utilizing X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). Furthermore, scanning electron microscope (SEM) and atomic force microscope (AFM) were employed to investigate surface morphology and topography of the layers. It was revealed that the layers had a porous structure with both anatase and rutile phases. The anatase relative content in the layers increased with the applied frequency; meanwhile, it decreased with duty cycle at low applied voltages, but... 

    Mapping the spatiotemporal variability of salinity in the hypersaline Lake Urmia using Sentinel-2 and Landsat-8 imagery

    , Article Journal of Hydrology ; Volume 595 , 2021 ; 00221694 (ISSN) Bayati, M ; Danesh Yazdi, M ; Sharif University of Technology
    Elsevier B.V  2021
    Abstract
    The spatiotemporal dynamic of salinity concentration (SC) in saline lakes is strongly dependent on the rate of water flow into the lake, water circulation, wind speed, evaporation rate, and the phenomenon of salt precipitation and dissolution. Although in-situ observations most reliably quantify water quality metrics, the spatiotemporal distribution of such data are typically limited and cannot be readily extrapolated for either long-term projections or extensive areas. Alternatively, remotely sensed imagery has facilitated less expensive and a stronger ability to estimate water quality over a wide range of spatiotemporal resolutions. This study introduces an adaptive learning model that... 

    Treatment of Oilfield Produced Water with Dissolved Air Precipitation/ Solvent Sublation

    , M.Sc. Thesis Sharif University of Technology Bayati, Fatemeh (Author) ; Shayegan, Jalaloddin (Supervisor)
    Abstract
    Because of production of large volumes of Produces Water during oil exploration, it is necessary to purify this water for reuse or discharging to environment. Thus, finding a suitable method for removing contaminations seems necessary. In the present study, removal of soluble and dispersed organic contaminants from produced water by Dissolved Air Precipitation/ Solvent Sublation has been studied. Combination of floatation by dissolved air and extraction with solvent has been used for removal of organic compounds in order to study simultaneous effect of both methods on removal efficiency. Samples used in the experiments were tested in two groups: the first group was synthesized samples of... 

    Treatment of oilfield produced water by dissolved air precipitation/solvent sublation

    , Article Journal of Petroleum Science and Engineering ; Volume 80, Issue 1 , 2011 , Pages 26-31 ; 09204105 (ISSN) Bayati, F ; Shayegan, J ; Noorjahan, A ; Sharif University of Technology
    2011
    Abstract
    Dissolved air precipitation/solvent sublation (DAP/SS) was used for treatment of simulated and real oilfield produced water to generate very fine bubbles which are necessary for effective separation. In this method micro bubbles produced by saturation of air in a pressurized packed column were released in an atmospheric column leading the bubbles to raise resulting trapped contaminants in the Gibbs layer around them to be removed by a layer of immiscible solvent at the top of column. The method was conducted to solutions including Benzene, Toluene and Chlorobenzene (ClB) as part of BTEX contaminants in produced water, mixture of them as simulated produced water and real oilfield produced... 

    A heuristic method for finding the optimal number of clusters with application In medical data

    , Article 30th Annual International Conference of the IEEE Engineering in Medicine and Biology Society, EMBS'08, Vancouver, BC, 20 August 2008 through 25 August 2008 ; 2008 , Pages 4684-4687 ; 9781424418152 (ISBN) Bayati, H ; Davoudi, H ; Fatemizadeh, E ; Sharif University of Technology
    IEEE Computer Society  2008
    Abstract
    In this paper, a heuristic method for determining the optimal number of clusters is proposed. Four clustering algorithms, namely K-means, Growing Neural Gas, Simulated Annealing based technique, and Fuzzy C-means in conjunction with three well known cluster validity indices, namely Davies-Bouldin index, Calinski-Harabasz index, Maulik-Bandyopadhyay index, in addition to the proposed index are used. Our simulations evaluate capability of mentioned indices in some artificial and medical datasets. © 2008 IEEE  

    Estimating the Spatial and Temporal Changes in The Salinity of the Hyper-Saline Lake Urmia Using Sentinel-2 Imagery

    , M.Sc. Thesis Sharif University of Technology Bayati, Majid (Author) ; Danesh-Yazdi, Mohammad (Supervisor)
    Abstract
    The spatiotemporal dynamic of salinity concentration (SC) in saline lakes is strongly dependent on the rate of water flow into the lake, water circulation, wind speed, evaporation rate, and the phenomenon of salt precipitation and dissolution. Although in-situ observations most reliably quantify water quality metrics, the spatiotemporal distribution of such data are typically limited and cannot be readily extrapolated for either long-term projections or extensive area. Alternatively, remotely sensed imagery has facilitated less expensive and a stronger ability to estimate water quality over a wide range of spatiotemporal resolutions. This study introduces an adaptive learning model that... 

    Simultaneous Analysis of Aliphatic Alcohols Mixtures Using an Electronic Nose Based on Nano/Microstructured Conducting Polypyrrole Film Prepared by Catalytic Electropolymerization on Cu/Au Interdigital Electrodes Using Multivariate Calibration

    , Article IEEE Sensors Journal ; Volume 16, Issue 2 , 2016 , Pages 418-425 ; 1530437X (ISSN) Alizadeh, N ; Babaei, M ; Alizadeh, M. S ; Mani Varnosfaderani, A ; Sharif University of Technology
    Institute of Electrical and Electronics Engineers Inc  2016
    Abstract
    In this paper, nano/microstructured-conducting polypyrrole has been prepared on Cu/Au interdigital electrode surfaces by using constant potential amperometry technique. The Fe(II) ions were used as catalyst and X = ClO4 -, pTs-, Cl-, TCA-, DS-, DBS- was implemented as anion dopants. The morphologies of the films were investigated by field emission scanning electron microscope. A remarkable dependence was observed between the type of anion dopant and the morphology of polypyrrole (PPy). The sensing behavior of the PPy-X sensor has been studied toward acetone, methanol, ethanol, 1-propanol, 2-propanol, nitromethane, propylamine, pyridine, and gas mixtures of aliphatic alcohols. The responses... 

    Molecular Dynamics Study of Tungsten and Iron Addition on the Glass Formability of Cobalt-based Electrodeposited Coatings

    , M.Sc. Thesis Sharif University of Technology Bayati, Mohammad Baher (Author) ; Tavakoli, Rouhollah (Supervisor)
    Abstract
    Recent research suggests that the electrochemical deposition of cobalt-based binary alloys, such as cobalt-tungsten and cobalt-iron, can lead to the formation of amorphous structures in the coatings. Theoretical studies suggest that these structures are equivalent to structures created by the melt cooling of the alloy at speeds of about 〖10〗^10 Kelvin per second. The formation of a glass phase can significantly increase the abrasion resistance and corrosion resistance of these coatings. Empirical studies show that the ability of the glass to become glassy, or more precisely, the transition from crystalline to amorphous, is largely a function of the chemical composition. Simulation of... 

    Micro-arc oxidized S-TiO2 nanoporous layers: Cationic or anionic doping?

    , Article Materials Letters ; Volume 64, Issue 20 , 2010 , Pages 2215-2218 ; 0167577X (ISSN) Bayati, M.R ; Moshfegh, A. Z ; Golestani Fard, F ; Sharif University of Technology
    2010
    Abstract
    S-doped TiO2 layers were grown on titanium substrates by MAO process. SEM results revealed a porous morphology with a pore size of 40-100 nm. Our XRD analysis showed that the anatase relative content reached its maximum value at the voltage of 500 V. The existence of sulfur in the states of S 4+ and S6+ which substituted Ti4+ in the titania crystalline lattice was confirmed by XPS results; meanwhile, no S 2- was detected. That is, a cationic doping was observed. EDS results showed that sulfur concentration in the layers increased with the voltage. The band gap energy was also calculated as 2.29 eV employing a UV-Vis spectrophotometer  

    Extracting Synergies in Nonlinear Dynamics and Investigating their Neural Basis

    , M.Sc. Thesis Sharif University of Technology Bayati, Hamid Reza (Author) ; Vosoughi Vahdat, Bijan (Supervisor)
    Abstract
    The existence of motor synergies in motor system as a tool for reducing degrees of freedom has been always debated. In the last two decades some experiments in vertebrates show the existence of motor primitives in spinal cord. In additional by recording electromyogram from frog some regular patterns have been shown. Recently, a motor coordination model based on stochastic optimal feedback control has extracted synergies by mathematical formulation. In addition, according to this model synergies are the optimal solution of the problem and not for simplifying it. However, this model is investigated in linear dynamics. In this thesis, first, an inverse method for extracting synergies is... 

    High performance grout connection for pre-cast concrete structures

    , Article International Conference on Sustainable Construction Materials and Technologies, Coventry, 11 June 2007 through 13 June 2007 ; 2007 , Pages 479-485 ; 9780415446891 (ISBN) Alizadeh Kharazi, M ; Sharif University of Technology
    2007
    Abstract
    Connections have very important role in pre-cast concrete structures, especially in seismic zones, and grout connections increase strength and resistance of pre-cast concrete structures for lateral forces. High performance grout connections (HPGC) provide new opportunities to design cost-effective pre-cast concrete structures. HPGC have been proposed to decrease cost of insulation, erection and crane cost of pre-cast concrete structures and to overcome weakness of traditional pre-cast concrete structure connections .This research focuses on properties of grout materials properties which produced in Iran and the effect of propylene fiber on the performance of grout connection. In the first... 

    Nanostructured materials for electronics and photonics

    , Article Journal of Nanomaterials ; Vol. 2014 , 2014 ; ISSN: 16874110 Bayati, R ; Mishra, Y. K ; Naseri, N ; Nori, S ; Sharif University of Technology
    2014
    Abstract
    [No abstract available]  

    Visible photodecomposition of methylene blue over micro arc oxidized WO3-loaded TiO2 nano-porous layers

    , Article Applied Catalysis A: General ; Volume 382, Issue 2 , Jan , 2010 , Pages 322-331 ; 0926860X (ISSN) Bayati, M. R ; Golestani Fard, F ; Moshfegh, A. Z ; Sharif University of Technology
    2010
    Abstract
    WO3-TiO2 nano porous layers were synthesized by micro arc oxidation (MAO) process under different applied voltages in electrolytes containing sodium tungstate and phosphate salts with various concentrations. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and energy dispersive X-ray spectroscopy (EDS) techniques were employed to study phase structure and chemical composition of the layers. According to our data analysis, the nano porous layers consisted of anatase, rutile, and tungsten oxide phases with a varying fraction depending on the voltage and electrolyte concentration. Moreover, it was found that WO3 not only dispersed in the TiO2 matrix, but also doped into the TiO2... 

    On the photocatalytic activity of the sulfur doped titania nano-porous films derived via micro-arc oxidation

    , Article Applied Catalysis A: General ; Volume 389, Issue 1-2 , 2010 , Pages 60-67 ; 0926860X (ISSN) Bayati, M. R ; Moshfegh, A. Z ; Golestani Fard, F ; Sharif University of Technology
    2010
    Abstract
    Sulfur doped TiO2 layers containing nano/micro-sized pores were synthesized by micro-arc oxidation process. Effect of the applied voltage and the electrolyte composition on physical and chemical properties of the layers was investigated using SEM, AFM, XRD, XPS, and EDS techniques. A UV-vis spectrophotometer was also used to study optical properties of the layers. It was found that the doped layers were porous with a pore size of 40-170 nm. They consisted of anatase and rutile phases with varying fraction depending on the applied voltage and electrolyte concentration. Our XPS investigations revealed the existence of sulfur in the forms of S4+ and S6+ states which substituted Ti4+ in the... 

    Synthesis of narrow band gap (V2O5)x-(TiO2)1-x nano-structured layers via micro arc oxidation

    , Article Applied Surface Science ; Volume 256, Issue 9 , 2010 , Pages 2903-2909 ; 01694332 (ISSN) Bayati, M. R ; Moshfegh, A. Z ; Golestani Fard, F ; Sharif University of Technology
    2010
    Abstract
    V2O5-TiO2 layers with a sheet-like morphology were synthesized by micro arc oxidation process for the first time. Surface morphology and topography of the layers were investigated by scanning electron microscope (SEM) and atomic force microscope (AFM). Phase structure and chemical composition of the layers were also studied by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques. It was revealed that the composite layers had a sheet-like structure average thickness of which was about 100 nm depending on the applied voltage. The layers consisted of anatase, rutile, and vanadium pentoxide phases fractions of which varied with the applied voltage. The optical properties... 

    Photo-degradation of methelyne blue over V2O5- TiO2 nano-porous layers synthesized by micro arc oxidation

    , Article Catalysis Letters ; Volume 134, Issue 1-2 , 2010 , Pages 162-168 ; 1011372X (ISSN) Bayati, M. R ; Golestani Fard, F ; Zaker Moshfegh, A ; Sharif University of Technology
    2010
    Abstract
    V2O5-TiO2 porous layers were synthesized via micro-arc oxidation for the first time. The effect of the applied voltage on morphology, composition, and photo-activity of the layers was investigated. The layers, which consisted of anatase, rutile, and vanadium pentoxide phases, revealed an enhanced photo-activity. About 93% of methylene blue solution was degraded on the synthesized layers after 120 min UV-irradiation with a reaction rate constant of k = 0.0228 min-1. The band gap energies of the vanadia-titania and pure titania layers were calculated as 2.56 and 3.39 eV, respectively  

    The effect of growth parameters on photo-catalytic performance of the MAO-synthesized TiO2 nano-porous layers

    , Article Materials Chemistry and Physics ; Volume 120, Issue 2-3 , 2010 , Pages 582-589 ; 02540584 (ISSN) Bayati, M. R ; Golestani Fard, F ; Moshfegh, A. Z ; Sharif University of Technology
    2010
    Abstract
    In this research, the effect of applied voltage and electrolyte concentration on structure, chemical composition, optical properties, and especially photo-catalytic activity of the TiO2 layers containing micro/nano-sized pores are discussed. TiO2 layers were synthesized by micro arc oxidation (MAO) process using different electrolyte concentrations and applied voltages. Surface structure of the layers was studied by scanning electron microscope (SEM); furthermore, energy dispersive spectrophotometry (EDS), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) techniques were employed to determine phase structure and chemical composition of the layers. Photo-activity of the... 

    How photocatalytic activity of the MAO-grown TiO2 nano/micro-porous films is influenced by growth parameters?

    , Article Applied Surface Science ; Volume 256, Issue 13 , 2010 , Pages 4253-4259 ; 01694332 (ISSN) Bayati, M. R ; Golestani Fard, F ; Moshfegh, A. Z ; Sharif University of Technology
    2010
    Abstract
    Pure titania porous layers consisted of anatase and rutile phases, chemically and structurally suitable for catalytic applications, were grown via micro-arc oxidation (MAO). The effect of applied voltage, process time, and electrolyte concentration on surface structure, chemical composition, and especially photocatalytic activity of the layers was investigated. SEM and AFM studies revealed that pore size and surface roughness of the layers increased with the applied voltage, and the electrolyte concentration. Moreover, the photocatalytic performance of the layers synthesized at medium applied voltages was significantly higher than that of the layers produced at other voltages. About 90% of...