Sharif Digital Repository

The objective of this work is making comparison between thermodynamic models and data-driven techniques accuracy in prediction of hydrate formation pressure as a function of temperature and composition of gas mixtures. The Peng-Robinson (PR) and Patel-Teja (PT) equations of state are used for thermodynamic modeling and Artificial Neural Networks (ANNs) and Adaptive Neuro-Fuzzy Inference System (ANFIS) are used as data-driven models. The capability of each method is evaluated by comparison with the experimental data collected from literature. It is shown that there is a good agreement between thermodynamic modeling and the experimental data in most of the cases; however, the prediction... 

This paper proposes a novel combinational Adaptive Noise Canceller (ANC), which is suitable for non stationary noise environments. Pre-filter bank structure improves the convergence rate leading to less error in real-time applications. During our investigations, we have found out adaptive algorithms have better performance for low frequency subbands. Thus, by using Singular Value Decomposition (SVD) in each subband, a simplified version of variable step-size algorithms has been employed in low frequency subbands; while for high frequency subbands, some conventional techniques have been used. Simulation results show that combination of adaptive and conventional methods have better performance... 

This paper studied the durability, microstructure, and fire behavior of lightweight mortars based on cement, metakaolin (MK), ultrafine ground granulated blast furnace slag (UGGBFS), ceramic waste powder (CWP), and clay brick waste powder (CBWP). Two sets of mixes were prepared with two types of lightweight aggregate including lightweight expanded clay aggregate (LECA) and pumice aggregate. Regarding the durability assessment, the electrical resistivity and water absorption of the mortars were measured. The UGGBFS-based alkali-activated mortar with pumice aggregate exhibited the highest electrical resistivity and lowest water absorption, while CBWP-based geopolymer mortar with LECA showed... 

The authors regret that there was an error in the XRD pattern for pumice shown in Fig. 8. The authors have re-analyzed the pumice to address the concerns over the reliability of the pattern due to the presence of noises, and the updated XRD pattern has been shown in Fig. 8 here for more accuracy of the presented information. It is noteworthy that this change does not affect any of the conclusions. The authors would like to apologise for any inconvenience caused. © 2021 Elsevier Ltd  

The authors regret that there was an error in the caption of Fig. 15. The corrected caption for Fig. 15 as presented here. It is noteworthy that this change does not affect any of the conclusions. Fig. 15. SEM micrograph of geopolymer mortar with clay brick waste: (a) with LECA and magnification of 60×, (b) with pumice aggregates and magnification of 2000×, (c) with pumice aggregates and magnification of 500×, (d) with pumice aggregates and magnification of 1000×. The authors would like to apologize for any inconvenience caused. © 2022 Elsevier Ltd  

A blind semi-invertible quantization based data hiding scheme, which reconstructs the original signal with high precision has been proposed. In order to produce correlated quantization yielding reversibility of the quantization based approach, a new transform domain has been introduced. In decoder, by compensating the quantization error and using the iterative technique, the original signal is recovered; then the watermarked signal is compared with the reconstructed original signal and hidden data is retrieved. Simulation results show that the proposed method in comparison with other reversible methods imposes less distortion and thus a higher Signal to Noise Ratio (SNR) is achieved. © 2009... 

In this paper, the optimum alkali activator solution properties in alkali-activated pastes based on ground granulated blast furnace slag (GGBFS) and micro-silica (MS) were investigated. For this purpose, sodium hydroxide (NH) solutions with molarities of 8 M, 12 M, and 16 M were prepared and mixed with sodium silicate (NS) solutions at NS:NH ratios of 1.0, 2.5, and 4.0 to produce the final activator solution. Two sets of pastes were manufactured: (1) pastes based on GGBFS, and (2) pastes in which 10% by weight of GGBFS was replaced with MS. The fresh density increased with increasing NH molarity and NS:NH ratio; whereas, the final setting time reduced with an increase in the aforementioned... 

A 6-bit passive phase shifter for S frequency band has been designed in a standard HEMT technology. A new switched-network topology has been proposed for implementing the 5.625 phase shift step which these digital bits are series with each other. We used Advanced Design System (ADS2010) to perform simulations. These digital bits will produce 64 different mode phase shift of -177.15 to +177.15 degree. In all cases simulation obtained less than 1 % error  

In this paper a self-oscillating mixer is presented fundamental signal generated by the oscillator subcircuit in the mixing process. The oscillator core consumes 3mA of current from a 1.8 V DC supply and results in an output power of -0.867 dBm per oscillator, and a measured phase noise of -91, -102 and -108 dBc/Hz at 100 KHz, 600 KHz and 1 MHz from the carrier, respectively. In the mixing process the proposed mixer achieved IIP3 of 0 dBm with conversation gain of 1.93 dB. The circuit was designed and simulated in 0.18-μm CMOS technology by ADS2010  

Purpose: The aim of this study was to compare diffusion tensor imaging (DTI) isotropic map (p-map) with current radiographically (T 2/T 2 -FLAIR) methods based on abnormal hyper-signal size and location of glioblastoma tumor using a semi-automatic approach. Materials and methods: Twenty-five patients with biopsy-proved diagnosis of glioblastoma participated in this study. T 2, T 2 -FLAIR images and diffusion tensor imaging (DTI) were acquired 1 week before radiotherapy. Hyper-signal regions on T 2, T 2 -FLAIR and DTI p-map were segmented by means of semi-automated segmentation. Manual segmentation was used as ground truth. Dice Scores (DS) were calculated for validation of semiautomatic... 

The authors regret that there was an error in the SEM image presented in Fig. 4(c) of the previously print version of the article. Please refer to the corrected SEM image as presented here. It is noteworthy that this change does not affect any of the conclusions. The authors would like to apologise for any inconvenience caused. © 2021 Elsevier Ltd  

The authors regret that there was an error in the SEM images presented in Fig. 4 of the article. The corrected SEM images as presented here. It is noteworthy that this change does not affect any of the conclusions. The authors would like to apologize for any inconvenience caused. © 2022 Elsevier Ltd  

Many smart grid applications need broadcast communications. Because of the critical role of the broadcasted messages in these applications, their authentication is very important to prevent message forgery attacks. Smart grid consists of plenty of low-resource devices such as smart meters or phasor measurement units (PMUs) that are located in physically unprotected environments. Therefore, the storage and computational constraints of these devices as well as their security against physical attacks must be considered in designing broadcast authentication schemes. In this paper, we consider two communication models based on the resources of the broadcasters and receivers and propose a physical... 

In this paper, the performance of an internal combustion engine is evaluated at the steady-state condition by application of energy and exergy analysis using the experimental test results. The energy and exergy balances are calculated at different engine speeds. The results show that the heat rejection of energy and exergy flow increases with increasing engine speed. The exergy efficiencies are slightly higher than the corresponding energy efficiencies. The results of this study have revealed that the most important source of the system inefficiency is the destruction of exergy by irreversible processes, mostly by the combustion. One can conclude that the use of a combined energy and exergy...