Sharif Digital Repository

Al6063 powder was subjected to severe plastic deformation via high-energy mechanical milling to prepare ultrafine-grained (UFG) aluminium alloy. Uniaxial compression test at various temperatures between 300 and 450 °C and strain rates between 0.01 and 1 s-1 was carried out to evaluate hot workability of the material. Microstructural studies were performed by EBSD and TEM. The average activation energy and strain rate sensitivity of the hot deformation process were determined to be 280 kJ mol-1 and 0.05, respectively. The deformation temperature and applied strain rate significantly affected the grain structure of UFG Al alloy. A finer grain structure was obtained at lower temperatures and... 

In the present work, hot workability of particulate-reinforced Al6061-20%SiC composite produced by direct hot extrusion technique was studied. Uniaxial hot compression test at various temperatures and strain rates was used and the workability behavior was evaluated from the flow curves and the attendant microstructures. It was shown that the presence of SiC particles in the soft Al6061 matrix deteriorates the hot workability. Bulging of the specimens and flow lines were observed, which indicates the plastic instability during hot working. Microstructure of the composites after hot deformation was found to be heterogeneous, i.e. the reinforcement clusters were observed at the flow lines. The... 

Flow curves and microstructural changes of nanostructured Al6063 alloy produced by mechanical alloying followed by hot extrusion were investigated by means of uniaxial compression test in the temperature range between 300 and 450 °C and strain rate range between 10-2 and 1 s-1. The analysis of flow curves were performed by a hyperbolic sine law equation and the stress exponent and activation energy were determined to be 2.9 and 228 kJ mol-1, respectively. The microstructural constituents for elaboration of deformation mechanisms were observed by TEM and EBSD under FEG-SEM. The microstructural observations determine that dynamic recovery through the formation of subgrains within the grains... 

The purpose of this paper is to develop a mathematical solution to estimate the deformation pattern and required power in cold plate rolling using coupled stream function method and upper bound theorem. Design/methodology/approach-In the first place, an admissible velocity field and the geometry of deformation zone are derived from a new stream function. Then, the optimum velocity field is obtained by minimizing the corresponding power function. Also, to calculate the adiabatic heating during high speed rolling operations, a two-dimensional conduction-convection problem is sequentially coupled with the mechanical model. To verify the predictions, rolling experiments on aluminum plates are... 

The aim of the present work is to study the effect of reinforcement content and sintering temperature on the densification and microstructural development during sintering of Al6061/SiC composite compacts. Prealloyed Al6061 powder was mixed with various amounts of SiC particles up to 27 vol.-% and compacted at 350 MPa. Sintering was carried out in a dry nitrogen atmosphere at 580-620°C. It was shown that the presence of SiC particles retards the densification of the prealloyed powder during solid phase sintering and liquid phase sintering. This effect is particularly noticeable at SiC fractions higher than ∼9 vol.-%, at which continuous networks of the hard particles are formed. Increasing... 

Compression test was used to study the deformation behaviour of sintered (12% porosity) and powder extruded (1% porosity) Al6061 alloy at high temperatures ranging from 350 to 500°C. The flow curves of the materials were determined at strain rates of 0.001, 0.01 and 0.1 s-1. The extruded alloy exhibited plastic instability in the form of bulging and formation of shear bands. The deformation activation energy of the extruded material was determined to be QI=77±16 kJ mol-1 (T<450°C) and OII=136±12 kJ mol-1 (T≥450°C). The values of activation energy and appearance of strain softening in the stress-strain curves revealed that thermally activated restoration processes, i.e. dynamic recovery and... 

In the present work, the role of graphite addition and sintering atmosphere on the laser sintering of M2 high-speed steel (HSS) powder was studied. The test specimens were produced using a continuous wave CO2 laser beam at power of 200 W and at varying scan rate ranges from 50 to 175 mm s-1 under nitrogen and argon atmospheres. It was found that laser scan rate and sintering atmosphere strongly influence the densification of M2 HSS powder. Opposite to the conventional sintering that the sinterability of HSS is improved by graphite addition, the result of this work demonstrated that graphite addition decreases the sintered density of M2 HSS at relatively low laser scan rates, i.e. <100 mm... 

We studied the flow stress and microstructural changes of nanostructured Al-6063 alloy produced by mechanical alloying at various temperatures and strain rates. The analysis of flow curves was performed by a constitutive equation, and the stress exponent and activation energy were determined as functions of strain. The deformation mechanisms were elaborated through microstructural observations by electron backscattering diffraction and transmission electron microscopy. Coarsening of the subgrains and grain growth upon deformation was monitored and related to the Zener–Hollomon parameter  

An ultrafine-grained Al6063/Al2O3 (0.8 vol.%, 25 nm) nanocomposite was prepared via powder metallurgy route through reactive mechanical alloying and hot powder extrusion. Scanning electron microcopy, transmission electron microscopy, and back scattered electron diffraction analysis showed that the grain structure of the nanocomposite is trimodal and composed of nano-size grains (< 0.1 μm), ultrafine grains (0.1–1 μm), and micron-size grains (> 1 μm) with random orientations. Evaluation of the mechanical properties of the nanocomposite based on the strengthening-mechanism models revealed that the yield strength of the ultrafine-grained nanocomposite is mainly controlled by the high-angle... 

Ultrafine-grained (UFG) Al6063/Al2O3 (0.8 vol%, 25 nm) nanocomposite was prepared via powdr metallurgy route. The grain structure of the nanocomposite composed of nano-size grains (< 0.1 μm), ultrafine grains (0.1-1 μm) and micron-size grains (>1 μm) with random orientations. It was found that the yield strength of the UFG nanocomposite is mainly controlled by the Orowan mechanism rather than the grain boundaries. The deformation activation energy at temperature ranges of T <300 ˚C and 300 ˚C ≤T < 450 ˚C was determined to be 74 and 264 kJ mol-1, respectively. At the higher temperatures, significant deformation softening was observed due to dynamic recrystallization of non-equilibrium grain... 

Ultrafine-grained (UFG) Al6063 alloy reinforced with 0.8 vol% nanometric alumina particles (25 nm) was prepared by reactive mechanical alloying and direct powder extrusion. Transmission electron microscopy and electron backscatter diffraction analysis showed that the grain structure of the nanocomposite composed of nanosize grains (<0.1 μm), ultrafine grains (0.1–1 μm) and micronsize grains (>1 μm) with random orientations. Mechanical properties of the material were examined at room and high temperatures by compression test. It was found that the yield strength of the UFG composite material is mainly controlled by the Orowan mechanism rather than the grain boundaries. The deformation... 

Nanostructured AA6063 (NS-Al) powder with an average grain size of ∼100 nm was synthesized by high-energy attrition milling of gas-atomized AA6063 powder followed by hot extrusion. The microstructural features of the consolidated specimen were studied by transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD) techniques and compared with those of coarse-grained AA6063 (CG-Al) produced by hot powder extrusion of gas-atomized powder (without using mechanical milling). The consolidated NS-Al alloy consisted of elongated ultrafine grains (aspect ratio of ∼2.9) and equiaxed nanostructured grains. A high fraction (∼78%) of high-angle grain boundaries with average... 

The general goal of the facility layout problem is to arrange a given number of facilities to minimize the total cost associated with the known or projected interactions between them. One of the special classes of the facility layout problem is the Single Row Facility Layout Problem (SRFLP), which consists of finding an optimal linear placement of rectangular facilities with varying dimensions on a straight line. This paper first presents and proves a theorem to find the optimal solution of a special case of SRFLP. The results obtained by this theorem prove to be very useful in reducing the computational efforts when a new algorithm based on tabu search for the SRFLP is proposed in this... 

In this paper, we have discussed the results of sensitivity analysis in a payoff matrix of the Matching Pennies game. After representing the game as a LP model, the sensitivity analysis of the elements of the payoff matrix is presented. The game value and the optimal strategies for different values of parameters are determined and compared  

Modified bitumen enhances the performance properties of asphalt mixtures. A number of studies in the last decade have evaluated the performance properties of modified binders at different service temperatures. It is however possible to evaluate some modified binder time-temperature characteristics and performance properties through their rheological master curves. In this research, styrene butadiene styrene, ethylene vinyl acetate, polyphosphoric acid and crumb rubber were used to modify a PG58-22 base binder. Rheological master curves for |G∗| and phase angles of these binders were generated using data from the dynamic shear rheometer and bending beam rheometer at temperatures ranging from...