Sharif Digital Repository

Optimization of transient liquid phase (TLP) bonding variables is essential to achieve a joint free from deleterious intermetallic constituents as well as with appropriate mechanical properties. In this research, TLP bonding of FSX-414 superalloy was performed using the MBF-80 interlayer. The effects of bonding time (1-30. min) and gap size (25-100 μm) were studied on the joint microstructure and its mechanical properties. Continuous centerline eutectic phases, characterized as nickel-rich and chromium-rich borides, were observed at the joints with incomplete isothermal solidification. The globular and acicular phases were seen at diffusion affected zone (DAZ). These phases could be... 

The as-cast samples of FSX-414 Co-based superalloy were heat treated at the standard solution and aging heat treatment cycles. Specimens for joining were cut from the as-cast ingot. Transient liquid phase (TLP) bonding was carried out at the standard solution cycle, using MBF-30 interlayer. Also, bonded specimens were homogenized at the standard aging condition. The microstructure of the as-cast, heat treated and TLP bonded specimens were studied. These studies showed that the non-uniform distributed carbides of the as-cast specimen were replaced by uniform ones during the heat treatment. Eutectic M 23C 6 carbides were observed in all specimens. Due to the complete isothermal solidification,... 

The as-cast FSX-414 Co-based superalloy samples were solution treated at 1150°C for 4h and then aged at 980°C for 4h. Specimens for joining were cut from the as-cast ingot and TLP bonding carried out at the same conditions as for the solution and solution+aging treatment, using MBF-30 interlayer. Microstructures were studied for as-cast, heat treated and TLP bonded specimens. These studies showed that the ununiform distributed carbides of MC type in the as-cast specimens replaced by M23C6 type carbides with uniform distribution in the heat treated microstructure. Due to complete isothermal solidification, no eutectic structure in the bond region were wasobserved, but some intermetallics in... 

4340 steel bars were austenitized at 850°C for 1 hour followed by heating at 700°C (ferrite and austenite region) for 90 min and quenching into a salt bath with different temperatures of 300, 350, 400 and 450°C. The steel bars were held for 1 hour at these temperatures before air cooling to room temperature. Various ferrite-bainite microstructures with 34% volume fraction of ferrite and different bainite morphologies were obtained. The results of SEM studies showed that by increasing the austempering temperature, the morphology of bainite varies from lower to upper bainite. According to the T-T-T diagram of the studied steel, the bainite transformation will not complete for the holding time... 

4340 steel bars were austenitized at 850 °C for 1 h followed by heating at 700 °C for 90 min and quenching into a salt bath at the temperature range of 300-450 °C for 1 h to obtain dual structures with 34 vol.% fraction ferrite and various bainite morphologies. SEM studies showed that by increasing the austempering temperature, bainite morphology varies from lower to upper bainite. Tensile, impact and hardness tests revealed that increasing the austempering temperature from 300 to 400 °C leads to a reduction in yield and ultimate tensile strength, hardness, uniform and total elongation and impact energy. But in dual phase steel produced by austempering at 450 °C, yield and tensile strength... 

In this study, the experimental finding of two half-scale interior prefabricated Reinforced Concrete column to Steel beam (RCS) sub-assemblage with proposed joint formations with and without web panel in the junction is presented. Previous researches about RCS have been performed to study shear strength of steel web panel in the joint by modeling joint component, however rarely have been conducted to evaluate joint shear resistance experimentally. Over the past 30 years, noticeable analytical and experimental assessments have been performed on the cast in place RCS joints, but seldom have been done on the prefabricated RCS. The steel beams in the proposed joint are attached to the expanded... 

In this paper, a new scheme for adaptiva subcarrier, bit and power allocation for downlink transmission of multiuser orthogonal frequency division multiplexing (OFDM) systems is presented. An adaptive algorithm is introduced to achieve the desired bit rate and BER for QoS (quality of service) of different users in a frequency selective fading channel, while the total transmit power is minimized. The performance and complexity of the proposed scheme is also thoroughly compared with the other existing methods. As the simulation results show, the proposed algorithm outperforms all prior sub-optimum schemes, while offering comparable computational complexity. © 2003 IEEE  

In this paper, a new scheme for adaptive subcarrier, bit and power allocation for downlink transmission of multiuser orthogonal frequency division multiplexing (OFDM) systems is presented. An adaptive algorithm is introduced to maximize the total data rate in a frequency selective channel, while satisfying requirements on total transmit power, minimum data rate of each user and desired BER to offer various quality of service (QoS) levels for different users. The performance and complexity of the proposed scheme is also compared with similar methods and other OFDM-based multiple access methods. Simulation results show that the proposed algorithm leads to higher performance in comparison with... 

The main objective of this paper is to provide comparative quantitative examinations on the capabilities of two-dimensional horizontal and pseudo-three-dimensional (3D) modelling approaches for simulating spatial and temporal variability of the flow and salinity in Lake Urmia, Iran. The water quality in the lake has been an environmentally important subject partly because this shallow hypersaline aquatic ecosystem is considered to be one of the largest natural habitats of a unique multicellular organism, Artemia urmiana. This brine shrimp is the major food source for many of the protected and rare shorebirds that visit the lake. A.urmiana can grow and survive in certain ranges of salinity,... 

The bonding temperature is an important parameter for optimization of the Transient Liquid Phase (TLP) bonding process in order to achieve a sound joint with good mechanical properties. However, the bonding temperature used can also be restricted by the microstructural stability of the base metal. In this study, the effect of bonding temperature (1050-1200 °C) on the joint microstructure and mechanical properties was studied for TLP bonding of FSX-414 superalloy using MBF-80 interlayer with thickness of 50 μm. Increasing bonding temperature from 1050 to 1150 °C caused reduction in the time required for complete isothermal solidification in agreement with models based on the diffusion induced... 

Co-based FSX-414 superalloy is especially used for first-stage nozzles of gas turbines. Transient liquid phase (TLP) bonding has potential as repair process for these nozzles. In this study, homogenization of TLP-bonded FSX-414 superalloy at optimum bonding condition (1150 °C/5 min) was conducted at 1175, 1200, and 1225 °C for 1, 3, and 6 h. Homogenization at 1175 °C/1 h had no effect on removing the diffusion-affected zone (DAZ) phases. Increasing the time to 6 h was effective in removing DAZ phases and boride phases formed due to liquefaction, but compositional homogenization was not complete. Homogenization at 1200 °C for 1 h caused boride phases to form adjacent to the joint and in the... 

To achieve a good performance of a boiler-turbine unit, dynamic variables such as steam pressure, water level of drum and electric output of turbine must be controlled. In this paper a nonlinear model of the boiler-turbine unit is considered in which the inputs are the valve positions of fuel flow, steam control, and feed-water flow. Using two control methods, feedback linearization and gain scheduling, a PI controller is designed. It is shown that by applying both methods, system goes from one operating point to another with an appropriate specification of time response. Results show that system with a controller designed based on gain scheduling method has a better time response from a...