Sharif Digital Repository

Recently, a renewed interest arises in the application of nanotechnology for the upstream petroleum industry. In particular, adding nanoparticles to fluids may drastically benefit enhanced oil recovery (EOR) and improve well drilling, by changing the properties of the fluid, rocks wettability alteration, advanced drag reduction, strengthening the sand consolidation, reducing the interfacial tension and increasing the mobility of the capillary trapped oil. In this study, we focus on roles of clay nano-particles on polymer viscosity. Polymer-flooding schemes for recovering residual oil have been in general less than satisfactory due to loss of chemical components by adsorption on reservoir... 

Inclusion of nano-clays into hydrogels is an efficient approach to produce nanocomposite hydrogels. The introduction of nano-clay into hydrogels causes an increase in water absorbency. In the present work, Nanocomposite hydro-gels based on kappa-carrageenan were synthesized using sodium montmorillonite as nano-clay. Acrylamide and meth-ylenebisacrylamide were used as monomer and crosslinker, respectively. The structure of nanocomposite hydrogels was investigated by XRD and SEM techniques. Swelling behavior of nanocomposite hydrogels was studied by varying clay and carrageenan contents as well as methylenebisacrylamide concentration. An optimum swelling capacity was achieved at 12% of sodium... 

In the present study, the out-of-phase thermomechanical fatigue (OP-TMF) behavior of a cast aluminum-silicon-magnesium alloy, the A356.0 alloy which has been widely used in diesel engine cylinder heads, is compared to room-temperature and high-temperature low cycle fatigue (RT-, HT-LCF) behaviors. For this purpose, strain/temperature-controlled isothermal and non-isothermal fatigue tests were performed based on realistic loading conditions in cylinder heads. Fatigue tests results showed that the plastic strain increased during cycles under constant mechanical strain amplitude, while the specimen failed. Under LCF loadings, the cyclic hardening occurred at low temperatures for the A356.0... 

Machine learning (ML) is generating new opportunities for innovative research in energy economics and finance. We critically review the burgeoning literature dedicated to Energy Economics/Finance applications of ML. Our review identifies applications in areas such as predicting energy prices (e.g. crude oil, natural gas, and power), demand forecasting, risk management, trading strategies, data processing, and analyzing macro/energy trends. We critically review the content (methods and findings) of more than 130 articles published between 2005 and 2018. Our analysis suggests that Support Vector Machine (SVM), Artificial Neural Network (ANN), and Genetic Algorithms (GAs) are among the most... 

The general approach to fault tolerance in uniprocessor systems is to maintain enough time redundancy in the schedule so that any task instance can be re-executed in presence of faults during the execution. In this paper a scheme is presented to add enough and efficient time redundancy to the Earliest-Deadline-First (EDF) scheduling policy for periodic real-time tasks. This scheme can be used to tolerate transient faults during the execution of tasks. We describe a recovery scheme which can be used to re-execute tasks in the event of transient faults and discuss conditions that must be met by any such recovery scheme. For performance evaluation of this idea a tool is developed. © 2007 IEEE  

The reliable transfer in Network on Chips (NoCs) can be threatened by crosstalk fault occurring in wires. Crossstalk fault is due to inter-wire coupling capacitance that based on the patterns of transitions appearing on the wires, significantly limits the reliability of NoCs. Among these transitions, 101 and 010 bit patterns impose the worst crosstalk effects to wires. This work intends to increase the reliability of NoCs against crosstalk faults by applying an improved Fibonacci-based numeral system, called Doubled-Penultimate Fibonacci (DP-Fibo). In the DP-Fibo coding algorithm, code words without ‘101’ and ‘010’ bit patterns are produced to reduce crosstalk faults. Experimental results... 

In the present work, specimens were cut out from St-37 plates with 19 mm thickness. The thickness of plates was reduced to 12.5 mm by milling and grinding operations. Then a standard V-shaped fillet was made on one edge of the plates. Two plates were butt-welded by standard metal arc gas (MAG) welding process. Residual stresses induced by welding were measured on 20 specimens by centre hole drilling. Load controlled axial fatigue tests were carried out to determine the fatigue life of specimens. Crack growth rates were obtained from experiment. Fractography of specimens was performed. Genetic Algorithm (GA) was employed for prediction of residual stress value in weldments using the crack... 

In this work, we implement some analytical techniques such as the Exp-function, Tanh, and extended Tanh methods for solving nonlinear partial differential equation, which contains sine terms, its name Double Sine-Gordon equation. These methods obtain exact solutions of different types of differential equations in engineering mathematics  

The qualitative effects of residual stress parameters on fatigue crack growth are investigated using Monte Carlo probabilistic analysis technique. These parameters include the maximum residual stress,σ0, half-width of the tensile residual stress region, b, and the redistribution of residual stress parameter, β. A normal distribution is assumed for all parameters considered in the investigation and fatigue life is determined using Forman equation. The results indicate that: (i) fatigue life decreases nonlinearly if the mean of random maximum residual stress and the half-width of tensile residual stress region increases; (ii) fatigue life increases nonlinearly if the rate of residual stress... 

In this paper residual stresses induced by butt metal arc gas welding (MAGW), in accordance with ASTM E837, are determined by hole drilling. The results are analyzed by probabilistic methods. Also, the effect of fatigue life on relaxation of welding residual stress is investigated. The specimens are tested to measure fatigue life and crack growth rates in accordance with ASTM E466 for force controlled amplitude axial fatigue testing. © 2008 Verlag Stahleisen GmbH, Düsseldorf  

The effect of contact geometry on fretting fatigue life was investigated by experiments and numerical simulation. The experiments were conducted for flat and cylindrical pads under the same contact normal force. The post-test examinations including crack growth measurements and fractography were carried out using optical and scanning electron microscopy (SEM). Numerical simulations of pad-specimen assembly with and without crack were performed using a finite element (FE) analysis. The experimental study revealed that the rate of crack growth was higher at the early stages of fretting fatigue for cylindrical pads. This stage corresponds to a higher KII for cylindrical contact model. After... 

A variational theory (VT), in which the potential energy of a real system is evaluated relative to the hard-sphere system, was used to investigate the medium's effects on the pair potential parameters. By adding the medium's effects to the isolated pair potential, the concept of an 'effective pair potential' (EPP) was introduced. The EPP parameters were compared with those of the average effective pair potential (AEPP) for Ar, which showed the importance of the medium effects and the long range interactions of the AEPP in dense fluids. The study showed that the depth parameter of the AEPP is much larger than that of the EPP  

In this article, out-of-phase thermo-mechanical fatigue (TMF) behaviours of light alloys were investigated in comparison to their high temperature low cycle fatigue (LCF) behaviours. For this objective, strain based fatigue tests were performed on the A356 aluminium alloy and on the AZ91 magnesium alloy. Besides, TMF tests were carried out, where both strain and temperature changed. The fatigue lifetime comparison demonstrated that the TMF lifetime was less than that one under LCF loadings at elevated temperatures for both light alloys. The reason was due to severe conditions in TMF tests in comparison to LCF tests. The temperature varied in TMF test but it was constant under LCF loadings.... 

In the present paper, thermo-mechanical fatigue (TMF) and low cycle fatigue (LCF) or isothermal fatigue (IF) lifetimes of a cast magnesium alloy (the AZ91 alloy) were studied. In addition to a heat treatment process (T6), several rare elements were added to the alloy to improve the material strength in the first step. Then, the cyclic behavior of the AZ91 was investigated. For this objective, strain-controlled tension-compression fatigue tests were carried out. The temperature varied between 50 and 200. °C in the out-of-phase (OP) TMF tests. The constraint factor which was defined as the ratio of the mechanical strain to the thermal strain, was set to 75%, 100% and 125%. For LCF tests,... 

This paper presents the fatigue lifetime of an aluminum-silicon-magnesium alloy, widely used in diesel engine cylinder heads, both with and without a thermal barrier coating (TBC) system. The coating system in this study consists of two layers including a 150 μm thick metallic bond coat and a zirconium oxide top coat 350 μm thick. These coating layers were applied on the substrate of A356.0 alloy by air plasma thermal spraying. The isothermal fatigue tests were conducted in low cycle fatigue (LCF) regime at various temperatures. Out-of-phase thermo-mechanical fatigue (OP-TMF) tests were also performed at different maximum temperatures and constraint factors. Experimental results demonstrate... 

In this paper, a new fatigue lifetime prediction model is presented for the aluminium-silicon-magnesium alloy, A356.0. This model is based on the plastic strain energy density per cycle including two correction factors in order to consider the effect of the mean stress and the maximum temperature. The thermal term considers creep and oxidation damages in A356.0 alloy. To calibrate the model, isothermal fatigue and out-of-phase thermo-mechanical fatigue (TMF) tests were conducted on the A356.0 alloy. Results showed an improvement in predicting fatigue lifetimes by the present model in comparison with classical theories and also the plastic strain energy density (without any correction... 

Recent research studies on ductile fracture of metals have shown that the ductile fracture initiation is significantly affected by the stress state. In this study, the effects of the stress invariants as well as the effect of the reverse loading on ductile fracture are considered. To estimate the reduction of load carrying capacity and ductile fracture initiation, a scalar damage expression is proposed. This scalar damage is a function of the accumulated plastic strain, the first stress invariant and the Lode angle. To incorporate the effect of the reverse loading, the accumulated plastic strain is divided into the tension and compression components and each component has a different weight... 

Recent experiments on metals have shown that all of the stress invariants should be involved in the constitutive description of the material in plasticity. In this paper, a plasticity model for metals is defined for isotropic materials, which is a function of the first stress invariant in addition to the second and the third invariants of the deviatoric stress tensor. For this purpose, the Drucker-Prager yield criterion is extended by addition of a new term containing the second and the third deviatoric stress invariants. Furthermore for estimating the cyclic behavior, new terms are incorporated into the Chaboche's hardening evolution equation. These modifications are applied by adding new... 

A simple functional form for a general equation of state based on an effective near-neighbor pair interaction of an extended Lennard-Jones (12,6,3) type is given and tested against experimental data for a wide variety of fluids and solids. Computer simulation results for ionic liquids are used for further evaluation. For fluids, there appears to be no upper density limitation on the equation of state. The lower density limit for isotherms near the critical temperature is the critical density. The equation of state gives a good description of all types of fluids, nonpolar (including long-chain hydrocarbons), polar, hydrogen-bonded, and metallic, at temperatures ranging from the triple point... 

The catalytic activity of potassium salts of phthalimide (PPI) and succinimide (PSI), as organonucleophilic catalysts, has been investigated for the cyclotrimerization of isocyanates under solvent-free conditions. PPI showed better catalytic activity in comparison with PSI. Diverse and challenging isocyanates afforded the respective symmetrical isocyanurates in good to quantitative yields in an atom economic reaction without any phase transfer catalyst. © 2005 Bentham Science Publishers Ltd