Sharif Digital Repository

In this paper, the effects of annealing temperature and time on mechanical properties and bond strength of aluminum clad steel sheet are evaluated. The results indicate that there exist an optimum annealing temperature and time for achieving a suitable formability and bonding strength between the clad layer and base metal. At this annealing time and temperature, the brittle intermetallic layer at the intimate interface of the layers is minimized. © 2003 Elsevier Ltd. All rights reserved  

A mathematical model for cold rolling of symmetrical sandwich strip is proposed using the upper bound theorem to investigate the plastic deformation behavior of the strip at the roll gap. The velocity fields derived from the proposed upper bound model can satisfy automatically the volume constancy and the velocity boundary conditions within the roll gap. Effects of various rolling conditions such as the initial thickness and flow stress of each layer in the strip, total thickness reduction and the frictional condition between the strip and roll on the rolling power, rolling force, and thickness reduction of each layer are discussed. Furthermore, experiments on sandwich strip rolling are... 

The production of an aluminum-clad steel sheet by the cold rolling process is a more efficient and economical approach compared with the other types of processes utilized for the production of such sheets. In this process, high plastic deformation of two metals, aluminum and steel, is necessary to create the cold bonding between the intermediate surfaces. Therefore, the work-hardened sheet must be annealed in order to obtain a high formability. Heat treatment of the sheet is, however, difficult due to the formation of a brittle intermetallic compound of aluminum and iron at the interface between the layers during heat treatment. In this investigation, the formability of these sheets was... 

This letter discusses the surface-reconstruction-induced self-twisting behavior of Si100 nanobelts and nanowires (NWs) with rectangular cross section. Giving a thorough physical interpretation, we explain the reason behind this phenomenon and present a continuum-based model. It is revealed that these structures can self-assemble into both right- and left-handed helicoids depending on their crystal arrangements. More specifically, for NWs with the same number of layers in each of their cross sections directions, two distinct values of torsion angle are possible for each of right- and left-handed twisted morphologies. In conclusion, four modes of torsion can be observed in Si100 NWs.... 

A mathematical model for cold rolling of two-layer strip is proposed using the upper bound theorem to investigate the plastic deformation behavior of the strip at the roll gap. The effects of total thickness reduction on the rolling power, rolling force, thickness reductions of each layer, and bonding strength of bimetal strip are discussed. Furthermore, experiments on two-layer strip rolling are conducted by employing aluminum-tin alloy and mild steel as the layers of the two-layer strips. It is found that all of theoretical predictions are in good agreement with the experimental measurements. Through the study, it becomes clear that the proposed analytical model is applicable for... 

The mechanisms of cold roll welding of aluminium alloy to steel strip has been assessed based on a study of interfacial behaviour at deformations of up to 60% together with the surface characteristics of peeled Al clad steel strip. The proposed mechanisms are applicable where the contact surfaces are degreased and then scratch brushed before the rolling deformation. According to this mechanisms the scratch-brushed layers are fractured shortly after entering the roll gap at a reduction of approximately 10%, which is about the threshold deformation for the roll bonding of aluminium to steel. The transfer cracks formed then become wider so that the distance between each coherent block increases... 

Purification of extracellular α-amylase from Bacillus subtilis was carried out via fractional precipitation by acetone and ion exchange chromatography. These steps provide fast precipitation as well as purification of α-amylase to improve enzyme purity, activity and stability. Compared with two-phase methods in which the yield was less than 1, this method resulted in a yield of more than 3. Moreover, 95% of acetone was recovered that enhanced the economy of the downstream process. Using the data provided by 2D electrophoresis, purification was done by a single step ion exchange chromatography. The enzyme exhibited a molecular mass (SDS-PAGE) of 50KD and the pI of 5. Maximum “yield” and... 

In today's global economy, the automotive design engineer's responsibilities are made more complex by the differences between regulatory requirements of the various global markets. This paper compares instrument panel head impact requirements of FMVSS 201 with its European counterparts, ECE 21. The behavior during a head impact test has been studied. Due to the gravity of the cockpit module, the sag has been analyzed to simulate shipping, loading, and assembly conditions. The interior parts of the vehicle cabin are exposed to temperature variations due to radiation effect of sun ray or freezing temperature in winter. Plastic parts appear to be more thermally susceptible than steel parts in... 

This study focuses on the mode classification of phones speaker modes using GMM 1. In this regard, speech data in both enabled and disabled speaker modes of cell phones and telephones were collected, processed and classified into two different categories. The different mixture numbers (1 to 4) of GMM and wave files sizes of 10, 20, 40 and 80 kb were tested in order to obtain an optimal condition for classification. The GMM method attained 87.99% correct classification rate on test data. This classification is important for speech enabled IVR 2 systems [1], dialog systems and many systems in speech processing in the sense that it could help to load an optimum model for increasing system... 

A novel MED-based desalination system for low-grade heat sources with a temperature between 65 °C and 90 °C has been proposed. Low-grade heat-driven desalination systems are of the most important methods for increasing energy efficiency and assisting the environment along with alleviating the water scarcity problem. The new proposed system is known as cascade multi-effect distillation (CMED). It is designed based on multi-step heat extraction from the heat source fluid (HSF). Multi-step heat absorption helps to form two arrays of MED effects and to utilize two boosters to achieve better performance. The advantage of this system is less complexity (for example, lower vapor injection), and... 

In this paper, the mechanical behavior of micro-rotating disks is investigated utilizing the strain gradient theory. The governing equation and boundary conditions are derived utilizing the variational method. The analytical solution for the derived equation is also presented. As a case study, some numerical results are presented to emphasize the importance of utilization of non-classical theories such as the strain gradient elasticity instead of the classical continuum theory in dealing with micro-rotating disks  

Magnetic nanoparticles (MNPs), Fe3O4@SiO2, have been prepared and functionalized by 3-(chloropropyl)trimethoxysilane and then by imidazole to synthesize Fe3O4@SiO2-Im. The functionalized Fe3O4 nanoparticles were used as a support to anchor manganese porphyrin via axial ligation. The prepared catalyst was characterized by elemental analysis, FT-IR spectroscopy, X-ray powder diffraction, UV-vis spectroscopy, and scanning electron microscopy. Application of immobilized manganese porphyrin as a heterogeneous catalyst in oxidation of alkenes and sulfides was explored. To find suitable reaction conditions,... 

A manganese porphyrin, meso-tetrakis(pentafluorophenyl)porphyrinato manganese(iii) acetate, Mn(TPFPP)OAc, was immobilized on silica-coated magnetic Fe3O4 nanoparticles functionalized with 3-aminopropyltriethoxysilane (APTS) through the amino propyl linkage using a grafting process in toluene solvent. This enabled the covalent immobilization of Mn(iii) porphyrin via an aromatic nucleophilic substitution reaction, to afford the Fe3O4@SiO2-NH2@MnPor catalyst. The resulting nanoparticles were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), FT-IR spectroscopy, UV-Vis spectroscopy, elemental analysis (CHN), atomic absorption spectroscopy (AAS), and vibrating... 

In this study, a new polymeric functionalized magnetic nanocatalyst containing a molybdenum Schiff base complex was prepared using a few consecutive steps. Poly (methylacrylate)-coated magnetic nanoparticles were synthesized via radical polymerization of methyl acrylate onto modified magnetic nanoparticles followed by the amidation of the methyl ester groups with hydrazine. Polymeric functionalization efficiently provides the advantage that more catalytic units can be grafted on the surface of magnetic nanoparticles. The functionalization process was continued with salicylaldehyde which introduced Schiff base groups on to the surface of the polymeric support. In the final step, the desired... 

Reo is an exogenous coordination language for synthesizing components participating in a component-based system. The notion of Bchi automaton over streams of records (BAR for short) is a proposed operational semantics for Reo that covers several aspects of coordination strategies such as synchronization, context dependencies and fairness constraints. In this paper and for the purpose of modeling real-time coordination systems specified by Reo, we present a timed version of BARs as the acceptors of timed streams of records. We show that timed BAR and its streams of records based semantics are more standard and also more expressive than timed constraint automaton which is the first proposed... 

The small-scale effects on the mechanical responses of micro-rotating disks with angular acceleration are investigated based on the strain gradient theory, as one of the powerful non-classical continuum theories which have been developed to justify the empirical observations of mechanical behavior in small-scale structures and components. The differential equations governing motion of the micro-disk elements in radial and circumferential direction together with the corresponding boundary conditions are derived. Then, an analytical solution is presented for the components of the displacement field which can be used as a base for determination of the components of the stress field. In a...