Sharif Digital Repository

Microstructural development and phase formation at the interface of yttria stabilized zirconia (3Y-TZP)/430L stainless steel composite layers produced by co-sintering method were studied by SEM, HRTEM, micro-focus XRD, and EPMA. Formation of a rich chromium boundary layer at the interface was noticed, which revealed Cr aggregation at the interface at the elevated temperatures. Misfit dislocations were also observed at the joint interface to tackle the mismatch crystallographic orientations between the ceramic and metal layer. The results of the micro-focus XRD showed formation of no new phases at the boundary zone. Microstructural studies also revealed a retarded grain growth in the... 

The mechanism of interface formation during sinter–joining of nanostructured yttria stabilized zirconia (27 nm) compacts with chromium powder was investigated. The effect of sintering atmosphere, i.e. argon or vacuum, was studied. Microstructural evaluation and phase formation was examined by scanning electron microscopy (SEM), electron probe micro-analysis (EPMA), and micro-focused X-ray diffraction (MFXRD) methods. It is shown that spreading and evaporation–condensation mechanisms are responsible for the interface formation. An improved joint shear-strength was obtained after sintering in vacuum (74 MPa) compared with argon (41 MPa). The result of MFXRD indicated formation of Cr-island at... 

Recently, co-powder injection molding process (2C-PIM) has attained considerable interest to fabricate complex-shaped functional materials. The aim of this work is to study the sintering compatibility between nanocrystalline yttria-stabilized zirconia (3Y-TZP) and PIM grade 430L stainless steel (SS) powders, which is the utmost important step in the 2C-PIM process. To evaluate the mismatch strain development during the co-sintering, the isothermal and nonisothermal behaviors of the ceramic and metal powders were studied. Small bilayers of 3Y-TZP/430L were made by a powder metallurgy technique and the feasibility of simultaneous sintering and joining of the composite layer was examined.... 

The sintering behavior of commercially available granulated ZrO2-3 mol% Y2O3 (3Y-TZP) powder compacts with an aggregate size of 75 nm was studied. The shrinkage response of the powder compacts during non-isothermal sintering was measured in a sensitive dilatometer at different heating rates. Densification and grain growth were also studied after isothermal firing in air according to different sintering cycles. The sintering and grain growth activation energy was estimated to be QS = 485 ± 12 kJ mol-1 and QG = 546 ± 23 kJ mol-1, respectively. Using the estimated Q-values, the master curves for sintering and grain growth were established and used for prediction of the densification and... 

TNT: Silicon microcantilevers modified with a three-dimensional layer of vertical titanium dioxide nanotubes can be used in micromechanical sensors with optical signal detection to detect low levels of explosives such as 2,4,6-trinitrotoluene (TNT) in the gas phase, even in the presence of other volatile impurities such as n-heptane and ethanol  

Sintering is the most critical step in manufacturing of functional parts by co-powder injection molding. In the present work, we studied the sintering phenomena occurring during co-sintering of metal/ceramic composite layers. Nanostructured yttria-stabilized zirconia (3Y-TZP) was co-sintered with 430L stainless steel and chromium. The sintering response was studied by dilatometer analysis in isothermal and non-isothermal modes. The microstructure of the sintered specimens was studied by scanning electron microscopy (SEM), electron-probe microanalysis (EPMA) and micro-focused X-ray diffraction (MFXRD). The strength of the joint was also determined by a shear-punch method. It is shown that... 

Manufacturing of complex-shaped bimetals utilizing two-color powder injection molding (2C-PIM) and three-dimensional printing (3DP) processes, which basically involve sintering of a powder/binder mixture, has been attracted a great interest. This article addresses sintering of biocompatible Co-Cr-Mo alloy for manufacturing stepwise porosity-graded composite structures. Such composite structures provide strength at the core and a porous layer for the tissue growth. To evaluate the process, two grades of gas atomized Co-Cr-Mo powder with an average particle size of 19 and 63 μm were used. Isothermal and nonisothermal sintering behavior of the loose powders under hydrogen and argon atmospheres... 

The fabrication of complex-shaped parts out of Co-Cr-Mo alloy and 316L stainless steel by three-dimensional printing (3DP) is studied using two grades of each alloy with average particle size of 20 and 75 nm, respectively. To produce sound specimens, the proper 3DP processing parameters were determined. The sintering behavior of the powders is characterized by dilatometric analysis and by batch sintering in argon atmosphere at 1280°C for 2h. The 3DP process has successfully produced complex-shaped biomedical parts with total porosity of 12-25% and homogenous pore structure, which is suitable for tissue growth into the pores  

To fabricate ceramic/metal complex-shaped part by co-powder injection moulding process (2KPIM), it is essential to tailor the sintering parameters in order to gain a low mismatch shrinkage, i.e. high sintering compatibility. In the present work, nanocrystalline 3Y-TZP and commercial 430L MIM grade stainless steel powders were co-sintered at various sintering cycles. Isothermal and non-isothermal sintering behavior of the individual and composite layers in argon and vacuum atmospheres were examined. High resolution scanning electron microscopy (HRSEM) coupled with energy dispersive X-ray (EDX) analysis was used to study the bonding interface between the ceramic and metal joints. It is shown... 

Microstructural development and phase formation at the interface of yttria stabilized zirconia (3Y-TZP)/430L stainless steel composite layers produced by co-sintering method were studied by SEM, HRTEM, micro-focus XRD, and EPMA. Formation of a rich chromium boundary layer at the interface was noticed, which revealed Cr aggregation at the interface at the elevated temperatures. Misfit dislocations were also observed at the joint interface to tackle the mismatch crystallographic orientations between the ceramic and metal layer. The results of the micro-focus XRD showed formation of no new phases at the boundary zone. Microstructural studies also revealed a retarded grain growth in the... 

The mechanism of interface formation during sinter-joining of nanostructured yttria stabilized zirconia (27 nm) compacts with chromium powder was investigated. The effect of sintering atmosphere, i.e. argon or vacuum, was studied. Microstructural evaluation and phase formation was examined by scanning electron microscopy (SEM), electron probe micro-analysis (EPMA), and micro-focused X-ray diffraction (MFXRD) methods. It is shown that spreading and evaporation-condensation mechanisms are responsible for the interface formation. An improved joint shear-strength was obtained after sintering in vacuum (74 MPa) compared with argon (41 MPa). The result of MFXRD indicated formation of Cr-island at... 

Manufacturing of complex-shaped bimetals utilizing two-color powder injection molding (2C-PIM) and three-dimensional printing (3DP) processes, which basically involve sintering of a powder/binder mixture, has been attracted a great interest. This article addresses sintering of biocompatible Co-Cr-Mo alloy for manufacturing stepwise porosity-graded composite structures. Such composite structures provide strength at the core and a porous layer for the tissue growth. To evaluate the process, two grades of gas atomized Co-Cr-Mo powder with an average particle size of 19 and 63 μm were used. Isothermal and non-isothermal sintering behavior of the loose powders under hydrogen and argon... 

A pressureless sintering method was utilized to fabricate metal/ceramic joints out of yttria-stabilized zirconia (3Y-TZP) and stainless steels (SS). Ultrafine (150 nm) and nanoscale (75 nm) 3Y-TZP particles and micrometric 17-4PH, 316L, and 420 SS (<31 μm) powders were tested. Isothermal and nonisothermal sintering behaviors of the powders and composite layers in hydrogen, argon, and vacuum atmospheres were examined. It was found that the mismatch strain between the zirconia ceramic and SS during cosintering is significant, which leads to bond cracking and joint failure. Nevertheless, interlayer diffusion of Zr, Fe, and Cr and the formation of a reaction zone, particularly during vacuum... 

Using multiple antennas at the transmit and receive sides of a passive radar brings both the benefits of MIMO radar and passive radar. However one of the obstacles arisen in such configuration is the receive antennas placement in proper positions so that the radar performance is improved. Here we just consider the case of positioning one receiver among multiple illuminators of opportunity. Indeed it is a start for the solution of optimizing the geometry of the multiple receivers in a passive radar  

SbCl3 supported on montmorillonite K-10 is an efficient catalyst for the ring opening of epoxides with aromatic amines under solvent-free conditions and microwave irradiation to give the corresponding b-amino alcohols in high yields with high regioselectivity  

In this paper, we consider an integrated sensing and communication (ISAC) system with wireless power transfer (WPT) where an unmanned aerial vehicle (UAV)-based radar serves a group of energy-limited communication users in addition to its sensing functionality. In this architecture, the radar senses the environment in phase 1 (namely sensing phase) and mean-while, the communications users (nodes) harvest and store the energy from the radar transmit signal. The stored energy is then used for information transmission from the nodes to UAV in phase 2, i.e., uplink phase. Performance of the radar system depends on the transmit signal as well as the receive filter; the energy of the transmit... 

One of the important obstacles in MIMO (Multiple Input Multiple Output) radars is the issue of designing proper transmit signals. Indeed, the capability of signal design is a significant advantage in MIMO radars, through which, the system can achieve much better performance. Many different aspects of this performance improvement have been considered yet, and the transmit signals have been designed to attain such goal, e.g., getting higher SNR or better detector's performance at the receiver. However, an important tool for evaluating the radar's performance is its ambiguity function. In this paper, we consider the problem of transmit signal design, in order to optimize the ambiguity function... 

Two gains play key roles in recently developed MIMO wireless communication systems: "spatial diversity" gain and "spatial multiplexing" gain. The diversity gain refers to the capability to decrease the error rate of the MIMO channel, while the multiplexing gain implicitly refers to the amount of increase in the capacity of the MIMO channel. It has been shown that there is a fundamental tradeoff between these two types of gains, meaning interplay between increasing reliability (via an increase in the diversity gain) and increasing data rate (via an increase in the multiplexing gain). On the other hand, recently, MIMO radars have attracted much attention for their superior ability to enhance... 

It is a well known fact that using multiple antennas at transmit and receive sides improves the detection performance. However, in such multiple-input multiple-output (MIMO) configuration, proper positioning of transmitters and receivers is a big challenge that can have significant influence on the performance of the overall system. In addition, determining the power of each transmitter under a total power constraint is a problem that should be solved in order to enhance the performance and coverage of such a system. In this paper, we design the Neyman-Pearson detector under the Rayleigh scatter model and use it to introduce a criterion for the antenna placement at both transmit and receive...