Sharif Digital Repository

Production of NiTi alloy from elemental powders was conducted by mechanical alloying (MA) and sintering of the raw materials. Effects of milling time and milling speed (RPM) on crystallite size, lattice strain, and XRD peak intensities were investigated by X-ray analysis of the alloy. Powder compaction and sintering time and temperature effects on pore percentage of the as-mixed and the mechanically alloyed samples were empirically evaluated. The crystallite size of the mechanically alloyed Ni50Ti50 samples decreased with MA duration and with the milling speed. Depending on the crystal structure of the raw materials, the lattice strain increases with the milling duration. Metallographic... 

Unlike those on Internet, the media providers on P2P networks are ordinary nodes with limited shared resources such as bandwidth. Multi-sender methods are the best existing solutions to video streaming on P2P networks. In this paper, we propose use of a multicast method on the top of an arbitrary multi-sender method so that all requesting peers receive almost the same expected bit-rate. Experimental results, derived from implementation of the proposed algorithm on Pastry P2P network confirm our claim. Another advantage of our method over the existing methods is its scalability with the number of receivers  

Switched Reluctance Motors (SRMs) are widely used in high-speed and low voltage applications because of their attractive features such as robustness and simplicity. No winding on the rotor of this type of motors allows reaching high speed which is desired for many applications. Drive circuits of SRMs also play an important role in their performance and operation. In this paper, a new bifilar drive circuit for this type of motors has been proposed. This novel configuration has been tested and investigated by PSIM software. Results show that the new bifilar drive circuit highly reduces the voltage stresses on semiconductor switches, and also considerably reduces the switching losses which are... 

Regarding the increasing number of electrical devices in the smart homes that leads to increase in total electricity consumption and cost, it is essential to use energy management methods to reduce the electricity cost. However, this can cause resident's dissatisfaction. Hence, it is important to define a method in which cost and dissatisfaction be optimized simultaneously. Among different services, an electric vehicle is the one that can be used as an energy storage system, so it can reduce the daily cost despite of increasing the total energy consumption. In this paper, we study the effect of the EV on the cost and dissatisfaction in our proposed method. © 2018 IEEE  

Using solid-state power amplifiers for next generation of weather radars becomes feasible by pulse compression techniques. In this study a 1.5 kW solid-state power amplifier (transmitter) for C-band weather radars is designed and fabricated by GaN high electron mobility transistor (HEMT) technology. An experimental setup based on heterodyne receiver with 16-bit digitiser is developed to investigate the behavior of the power amplifier under different cooling methods and back-off points. Several measurements with shaped LFM pulse show an approximately identical pulse to pulse (P2P) stability for 3 dB compression, P1dB and 2 dB back-off points while the best sidelobe level (SLL) is achieved for... 

Application of Probabilistic Safety Assessment (PSA) to a Uranium hexafluoride (UF 6) production process is presented in this paper. The process is constituted from three main units: UF 4 conversion to UF 6, condensation of produced UF 6 gas and tail gas treatment. Radioactive gas is present in all parts of the process and occurrence of high pressure or high temperature in the process equipments may lead to radioactive release to workplace and environment. The work is mainly based on PSA experience in nuclear power plants. Accordingly for the process, eight group of Initiating Events (IE) that lead to UF 6 gas release have been identified using HAZOP study. For each IE, based on related... 

In self-controlling hyperthermia therapy, once the desired temperature is reached, the heat generation ceases and overheating is prevented. In order to design a system that generates sufficient heat without thermal ablation of surrounding healthy tissue, a good understanding of temperature distribution and its change with time is imperative. This study is conducted to extend our understanding about the heat generation and transfer, temperature distribution and temperature rise pattern in the tumor and surrounding tissue during self-controlling magnetic hyperthermia. A model consisting of two concentric spheres that represents the tumor and its surrounding tissue is considered and temperature... 

This study investigates the aerodynamic loads and energy losses of a typical 600 kW wind turbine with S816 airfoil blade under two different icing conditions. Three sections at different radial positions were considered to estimate the icing effect along the blade. Ice accretion simulations in wet and dry regimes were carried out using the NASA LEWICE 3.2 computer program. The airflow simulations were performed with CFD method and SST k -ω turbulence model. The results of these simulations, including streamlines, surface pressure, skin friction, lift, and drag coefficients, were inspected for both clean and iced airfoils. In the case of wet iced airfoil, a separation bubble was created in... 

Isotropic tensor valued functions of tensor arguments play an important role in the formulation of the equations governing the behavior of solid materials in the field of continuum mechanics. When the tensor argument is non-symmetric, the complexity and the difficulty in dealing with the tensor functions are high. In this work, the issue of expressing an isotropic tensor valued tensor function of a non-symmetric tensor argument is attention by utilizing the Dunford-Taylor integral. An important subclass of the isotropic tensor functions is considered with the commutative property  

The objective of this study is the investigation of formaldehyde degradation in a bioreactor with pumice stone as a support. The reactor was tested at different synthetic wastewater concentrations with total COD of 500, 1000 and 1500 mgL, respectively, at 24 h hydraulic retention time. The effect of feed composition was tested by changing the COD TCOD FA ratio in order to analyze the impact of formaldehyde concentration. The average formaldehyde and COD removal efficiencies obtained in the reactor were 97.1% and 88%, respectively. The maximum COD and formaldehyde removal efficiencies occurred at the COD TCOD F of 41 at COD T=1000mgL. The effect of toxic shock on reactor performance was... 

This paper is devoted to the design of a port Hamiltonian controller for different scenarios of brachiation movement by a two-link bio-inspired robot called brachiating robot. A unified technique for trajectory tracking control problem of nonholonomic (drift-less) port Hamiltonian systems was introduced in the past, which exploits a generalized canonical transformation to form an error system in order to convert the trajectory tracking problem into a stabilization one. Although the method is novel and promising, only fully actuated systems are considered and success of the approach relies on the possibility of solving a set of partial differential equations (PDEs). Considering the fact that... 

Recently, the mechanisms of natural undulatory locomotion of aquatic animal swimming have become one of the most significant issues for the researchers, swimmers and engineers. This study aims to elucidate and compare the propulsive vortical signature and performance of backward (negative undulation) and forward (positive undulation) travelling waves through a typical fishlike propulsor by a systematic numerical study. The numerical approach uses a pressure-based finite volume method solver to solve Navier–Stokes equations in an arbitrary Lagrangian–Eulerian framework domain containing a two-dimensional NACA 0012 foil moving with prescribed kinematics. Some of the important findings are: (1)... 

The hydrodynamics and energetics of bioinspired oscillating mechanisms have received significant attentions by engineers and biologists to develop the underwater and air vehicles. Undulating and pure heaving (or plunging) motions are two significant mechanisms which are utilized in nature to provide propulsive, maneuvering, and stabilization forces.This study aims to elucidate and compare the propulsive vortical signature and performance of these two important natural mechanisms through a systematic numerical study. Navier-Stokes equations are solved, by a pressure-based finite volume method solver, in an arbitrary Lagrangian- Eulerian (ALE) framework domain containing a 2D NACA0012 foil... 

Recently, the mechanisms of natural undulatory locomotion of aquatic animal swimming have become one of the most significant issues for the researchers, swimmers and engineers. This study aims to elucidate and compare the propulsive vortical signature and performance of backward (negative undulation) and forward (positive undulation) travelling waves through a typical fishlike propulsor by a systematic numerical study. The numerical approach uses a pressure-based finite volume method solver to solve Navier–Stokes equations in an arbitrary Lagrangian–Eulerian framework domain containing a two-dimensional NACA 0012 foil moving with prescribed kinematics. Some of the important findings are: (1)... 

A micromechanical phase-field model is utilized to study the evolution of nanostructure Al3Sc phase in Al-Sc alloy. We study the formation of Al3Sc precipitates in an Al-Sc alloy by using an elastic phase-field model. Since the precipitates of Al3Sc phase are fully coherent with the Al matrix, the elastic energy will have an inuence on the resulting morphology. We have studied the effects of elastic strain energies on shape evolution of Al3Sc phase, numerically. The simulated nano-structures evolve from spherical to cubic shapes. The equilibrium shape of the coherent Al3Sc phase is found to be determined by minimizing the sum of the elastic and interfacial energies through the phase-field... 

In this study, the effect of deploying microtabs on performance improvement of a horizontal axis wind turbine blade is numerically investigated in three-dimensions. The NREL Phase VI, a stall-regulated upwind wind turbine, is used as the baseline case. Different cases are considered to investigate the effects of spanwise location as well as the height variation of tabs along the blade span, on the flow over the rotor blade. In all cases, the tab is located at 95% chord of the airfoil section on the lower surface of the blade. Results reveal that locating microtabs at the outboard part of the blade has a greater impact on the rotor performance than the inboard part. However, both cases... 

The main purpose of this paper is to investigate the feasibility of using field programmable gate arrays (FPGAs) chips as alternatives for the conventional CPUs to accelerate the numerical solution of the fluid dynamics differential equations. FPGA is an integrated circuit that contains an array of logic blocks, and its architecture can be reprogrammed and reconfigured after manufacturing. Complex circuits for various applications can be designed and implemented using FPGA hardware. The reconfigurable hardware used in this paper is a system on a chip FPGA type that integrates both microprocessor and FPGA architectures into a single device. In this paper, typical computational fluid dynamics...