Sharif Digital Repository

Austenitic stainless steels are the most common kinds of stainless steels. Although these alloys are generally very weldable, there are some problems in join- ing of them using fusion welding. Solidification and liquation cracking or corrosion at grain bound- aries in the heat-affected zone are examples of these problems. Transient liquid phase (TLP) bonding is an important variation of diffusion bonding that has the potential to overcome this problems. Two-step TLP bonding is an ingenious development to form non-planar interface. This method consists of a short-time high temperature heating to melt interlayer followed by isothermal solidification of liquid phase at a lower temperature. In... 

Considering the wide applications of 304 stainless steel in various industries and the existing literature on transient liquid phase bonding of stainless steels with a variety of interlayers, the present work aimed to reduce the bonding time by using a two step bonding method. Faster bonding reduces both energy consumption during bonding and the base metal grain growth. It also leads to a lower reduction in the base metal and joint strength.Due to the melting point of the interlayer, different durations and a temperature of 1200°C were selected for the first step. This temperature was maintained for a specified period of time before it sharply dropped to and remained at 1180°C (the... 

Simultaneous detection of pH and glucose levels in sweat is a promising tool for early skin disease detection and diabetes diagnosis. Hydrogels have attracted a lot of attention in the field of wearable biosensors due to sweat absorption capability, biocompatibility, and the ability to store enzymes and reagents in their cavities. In this research, we have presented an innovative wearable colorimetric biosensor based on polyvinyl alcohol (PVA) hydrogel, which can simultaneously measure pH level (in the range of 3-9) and glucose concentration (in the range of 0.025-0.5 mM) of sweat with the help of machine learning (ML). This wearable sensor consists of two main parts: sensors and a patch, in... 

High-strength low alloy (HSLA) E275 developed specifically for automotive application. Also St12 Steel is used in autobodies. On the other hand the resistance spot weld of dissimilar materials is generally more challenging than that of similar materials due to differences in the physical, chemical and mechanical properties of the base metals. The influence of the primary welding parameters affecting the heat input such as; current and time on the morphology, fracture mode, microhardness, and tensile shear load bearing capacity of dissimilar welds between HSLA E275 steel and St12 steel in two different thicknesses (1,2 mm) has been investigated in this study which consisted six group. The... 

This thesis studies the possible solution to the H0 tension via a dynamical systems approach. The early dark energy (IDE) scenario can somewhat alleviate the Hubble constant tension. On the other hand, postulating a new subdominant EDE in the pre – recombination Universe can also resolve the H0 tension. We introduce a novel model to interweave the early dark energy(EDE) and interacting dark energy-dark matter (IDE) scenarios. In this scenario, the early dark energy emerges naturally by changing the topological class of the phase portrait of the universe dynamics. In particular, an EDE component contributing only 10% of the matter density of the Universe—preferably in the vicinity of the... 

Temerature fluctuation of the Cosmic Microwave Background (CMB) is one of the key observebles of the modern cosmology. Today, it is widely believed that quantum fluctuation that are stretched to horizon scales during a period of acceleration expansion -- at the onset of evolution of the universe-- are responsible for these perturbations. In the simplest scenarios of the inflation, a scalar field is responsible for both nearly expansional expansion of the universe and the proimordial fluctuations. In this thesis, we investigate the models of inflation with an additional light degree of freedom. In particular, we employ the method of the Effective Field Theory to study the general structure... 

By studying of simulations, it can be seen that the linear point (LP), a point lies midway between the scales associated with the peak and the dip in the correlation function on BAO scales, is a useful window into cosmology and large scale structures rather than baryonic echo peak. Some fundamental features of the LP, been unaffected by redshift space distortions and gravitational non-linear effects, has made it important. I want to find evidences to stability of the LP by utilizing Standard Perturbation Theory through my thesis  

The introduction of multi phase steels in recent years resulted in a considerable increase in development of some industries such as automobiles. By inducing soft and hard phases together, these steels could bring better mechanical properties than classical ones. Recent studies on 4340 ferritic- bainitic and ferritic- martensitic dual phase steels, indicate that 34 volume percent ferrite with hard phase, has the best combination of strength, toughness and fatigue properties. In present research, by proper heat treatment on a 4340 steel, it is tried to prepare specimens ferritic- bainitic- martensitic triple phase steels with 34 volume percent of ferrite and different percents of martensite.... 

In the research transient liquid phase bonding of AL6061-SiC composite was performed using copper as interlayer. The joining praocess was performed in various tetemperatures (560c and 580c and 600c) And times (6 and 8 hours). Optimum Joining condition was determined by using optical and of the joint, micro hardness test was performed from the bonding zone to the bulk of the base composite. The fatigue endurance limit of Al6061-SiC composite was determined by several fatigue tests and TLP bonded samples were loaded under achieved endurance limit stress. Finally fatigue fracture surface of both base composite and TLP bonded samples were studied by using of scanning electronic microscope  

In this research, transient liquid phase (TLP) bonding of FSX-414 superalloy was investigated using MBF-80 interlayer. The bonding was performed at different temperatures (1050-1200oC) for various times (1-120min). Also, different gap sizes were studied using the interlayer with various thicknesses (25-100µm). Homogenizing treatment was performed at different temperatures (1175-1225oC) and times (1-6h) for the samples with complete isothermal solidification. The microstructure of the samples were studied using the optical, scanning electron and transmission electron microscopes. Also, XRD, SEM/EDS, SEM/WDS and TEM/EDS analyses were used to analyse the observed phases at the joints. To... 

AISI 4340 steel bars were austenitized at 900°C for 1 hour followed by heating at 740°C (ferrite and austenite region) for 100 min and quenching into a salt bath at 300°C for different times followed by quenching into water to obtain triple phase microstructures with 34 Vol.% ferrite and various martensite (or bainite) contents. Presence of three phases in adjacent of each other confirmed by metallographic analysis and TEM technique. Volume fraction of different phases was measured by image analyser. The results of optical microscopy showed that by increasing VM, morphology of martensite varies from uniform distribution of small spherical network particles to large blocky islands with... 

Interlayer composition as one of the most important factors of TLP bonding could affect bonding region composition and microstructure that both of them govern the mechanical properties of the joint. Due to the risk of substrate microstructure degradation , welding of dual phase steel needs more cautions. TLP bonding ideally acquires joints having more similar microstructure to substrate. Moreover , using this method could avoid the change of base metal microstructure when heat treatment of carbon steel is postponed until after bonding. Fe-based , Ni-based and commercially pure Cu are three different composition has been studied in this work. The bonded samples were investigated by optic and... 

Dual Phase ferritic-martensitic steels are kind of high strength low alloy steels (HASLA) which are widely used in industry because of their strength and formability. Since welding of dual phase steels in conventional welding methods causes structural change and Subsequently alters mechanical properties of both weld zone and heat affected zone(HAZ), additional operations which are not commercially viable is needed to achieve a dual phase structure in structurally changed regions. In this study, transient liquid phase (TLP) bonding method is used during dual phasing process in order to preserve dual phase ferritic-martensitic structure and avoid extra heat treatment. Applied pressure during...