Sharif Digital Repository

The evolution of microstructure and the mechanical properties of an aluminum 6061 alloy tube subjected to a novel severe plastic deformation process called tube channel pressing were studied. Results show that the tube channel pressing causes an impressive grain refinement and strengthening of the material. As an illustration, mostly ultrafine grained tube (D-=760nm) bearing the yield strength of 352. MPa can be obtained after 5 passes of tube channel pressing. Additionally, the tube channel pressing causes the heterogeneous grain refinement resulting in a bimodal distribution of size of grains after 7th pass. Therefore, it can be inferred that the main microstructure refining mechanism... 

In this work, the 6061 aluminum alloy tubes are severely deformed through a novel method called Tube Channel Pressing (TCP). The ability of this process in improving mechanical properties, grain refinement and microstructural changes of the alloy with different heat treatments before and after TCP process is investigated. Results show that TCP has notable effect on grain refinement and decreases crystallite size of solid solution treated aluminum 6061 material to 52. nm after equivalent strain of 3.09 which is comparable with the measured data from other SPD processes. The strength of the specimens aged before TCP is higher than that of those aged after TCP. The specimens artificially aged... 

Natural aging behavior of the aluminum 6061 alloy after a novel Severe Plastic Deformation process called Tube Channel Pressing (TCP) was studied. For this purpose, Vickers microhardness test was used to investigate the changes of mechanical properties while TEM and XRD observations were utilized in order to characterize microstructural evolution during natural aging. Results show that Si-enriched precipitates appear and coarsen rapidly in the first few days of natural aging of TCPed aluminum 6061 alloy which causes consecutive increase and decrease of Vickers microhardness, respectively. Similarly, other alloying elements such as Cu and Fe lead to formation of coarse precipitates during... 

This study is aimed to realize evolution of microstructure and mechanical properties of aluminum 6061 alloy tube subjected to Severe Plastic Deformation (SPD) and subsequent annealing. For this purpose, the tube is initially processed by different passes of an SPD process called Tube Channel Pressing (TCP) and then subjected to a subsequent annealing at 473. °K for 2. h. Afterwards, tension test is used for the evaluation of mechanical properties while Electron Back-Scattered Diffraction (EBSD) equipped Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM) are utilized for the microstructural characterizations. Results show that the Continuous Static Recrystallization... 

The effect of heat treatment on the axial crushing behavior of thin-walled aluminum 6061 alloy tubes is studied in this work. For this purpose, thin-walled grooved specimens were subjected to different aging heat treatments to obtain different work hardening behaviors. Afterward, quasi-static axial compression tests were achieved to evaluate the crushing behavior. Additionally, a finite element method simulation was employed to determine the distributions of stress, strain, and imposed damage during axial compression. Results show that the optimum energy absorption characteristics can be obtained using moderated strain hardening exponent, ''n''. Low strain hardening exponent results in the... 

The deformation behavior of solid solution-treated AA6061 tubes in a novel severe plastic deformation process named Tube Channel Pressing has been assessed. In order to do so, an analysis based on the finite element method and dislocation density model is utilized, and microhardness measurement is carried out to verify the trends of analysis results. By comparing FEM results with experimental data, the optimized geometrical parameters controlling the deformation behavior of the tube in tube channel pressing are determined to obtain the best strain homogeneity and minimum dimensional changes in tube  

The effects of die geometry on the deformation behavior of aluminum 6061 alloy tube in a novel severe plastic deformation (SPD) process called tube channel pressing (TCP) were studied using the Abaqus 6.10 software. Using the optimized die geometry, 1 to 3 passes of TCP is imposed not only to validate the simulation results, but also to investigate the performance of TCP as a SPD process. The finite element method (FEM) simulation results show that the moderated plastic strain, the lower inhomogeneity in distribution of plastic strain, and the lower risk of fracture during process can be obtained using the proper die geometry. In addition, the imposed strain is a mixture of shear strain and... 

Nanowire arrays of copper oxide were first grown vertically using simple and cost effective thermal oxidation method on a copper foil. Subsequently, in order to deposit and grow PbS nanocyrstalline thin films on CuO NWs by utilizing the chemical bath deposition technique, these arrays were immersed as the substrate in the reaction solution consisting of Pb(NO3)2, (NH2)2CS and NaOH. The final products were characterized in detail by which the formation of uniform, unique arrays of CuO@PbS core–shell NWs was confirmed. Due to the nature of methods employed in synthesis of this hetero structure, the tuning of core and shell size and consequently properties of the novel structure is easily... 

In a MIMO (Multiple Input Multiple Output) radar system, proper design of transmit signal and receive filter is an advantageous tool to improve the detection performance. Thus, in this paper, we consider the problem of transmit code and receive filter design, in order to maximize the Signal to Noise Ratio (SNR) at the receiver while enforcing a similarity constraint between the transmit space-time code (STC) and a reference STC which has a desirable ambiguity function. We will show that by solving such constrained optimization problem through successive iterations, our proposed method leads to satisfactory results  

Weighting elements to achieve radiation patterns with desired characteristics is a classical work in phased array antennas. These characteristics can be low sidelobe level, narrow beamwidth, high directivity, pattern nulling in special angle and etc. For each of these characteristics, different methods have been introduced. Most of methods have been presented for uniform arrays, however there are lots of methods to obtain a desired pattern for antennas with non-uniform element distances. The problem with these methods is complexity or not very good results. In this paper, fast and easy methods based on Least Square Error that leads to good results are presented. In addition, weighting of... 

Distributed generation connected with AC, DC, or hybrid loads and energy storage systems is known as a microgrid. Campus microgrids are an important load type. A university campus microgrids, usually, contains distributed generation resources, energy storage, and electric vehicles. The main aim of the microgrid is to provide sustainable, economical energy, and a reliable system. The advanced energy management system (AEMS) provides a smooth energy flow to the microgrid. Over the last few years, many studies were carried out to review various aspects such as energy sustainability, demand response strategies, control systems, energy management systems with different types of optimization... 

This paper resolve the salinity-dependent interactions of polar components of crude oil at calcite-brine interface in atomic resolution. Molecular dynamics simulations carried out on the present study showed that ordered water monolayers develop immediate to a calcite substrate in contact with a saline solution. Carboxylic compounds, herein represented by benzoic acid (BA), penetrate into those hydration layers and directly linking to the calcite surface. Through a mechanism termed screening effect, development of hydrogen bonding between –COOH functional groups of BA and carbonate groups is inhibited by formation of a positively-charged Na+ layer over CaCO3 surface. Contrary to the common... 

An important tool for assessing a radar's performance is the ambiguity function. On the other hand, many different schemes have been designed for the transmit waveforms of a MIMO radar. For each one, a criterion has been chosen to improve the performace, e.g. achieving better missed detection. In this paper, considering the ambiguity function as the benchmark, we propose a waveform design scheme, which optimizes the ambiguity function of the MIMO radar system  

Flow hydrodynamics of laminar falling film of aqueous Li Br solution (Li Br - H2O) on a horizontal elliptical tube has been investigated in this research. The film velocity distribution and film thickness, namely, the flow characteristics are determined by solving analytically simultaneous simplified Navier - Stokes equations and continuity equation in polar and Cartesian coordinates. The analysis is based on steady state laminar flow of falling liquid film of Li Br - H2O on a horizontal elliptical tube in polar model and Cartesian model (CM), for cases in which traction on the film surface is considered negligible. Models are compared with each other in three cases of aspect ratios (Ar),... 

Velocity distributions in (r,θ) directions are evaluated by solving simultaneous simplified Navier-Stokes equations (NSE) and continuity equation (CE) in polar coordinate. The analysis is based on steady state laminar flow of thin falling liquid film on a horizontal circular tube, for cases in which traction on the film surface is considered negligible. It is a common geometry for part of engineering problems such as evaporator, condenser, absorber, generator of absorption chillers and other similar units in mechanical and chemical engineering. Knowledge of the velocity profiles is usually needed for: 1 - solving governing energy and species equations 2- estimating the average and film... 

Velocity distributions in (r,θ) directions are evaluated by solving simultaneous simplified Navier-Stokes equations (NSE) and continuity equation (CE) in polar coordinate. The analysis is based on steady state laminar flow of thin falling liquid film on a horizontal circular tube, for cases in which traction on the film surface is considered negligible. It is a common geometry for part of engineering problems such as evaporator, condenser, absorber, generator of absorption chillers and other similar units in mechanical and chemical engineering. Knowledge of the velocity profiles is usually needed for: 1- solving governing energy and species equations 2- estimating the average and film... 

This work concerns the experimental investigation of surfactant alternating CO 2 injection in carbonate rocks. The core samples provided from a low-temperature fractured light oil reservoir, located in southwest Iran. The experiments were designed to observe the effect of CO 2-foam injection on gas mobility and oil recovery at different surfactant concentrations. The core samples were initially saturated with synthetic/field brine, 5,000 ppm, and then flooded with live oil to reach connate water saturation at reservoir condition, 115F and 1,700 psia. The commercial surfactant used was sodium lauryl sulfate as an anionic surfactant. The results of this work, along with field-scale simulation... 

Knowledge of Air-water two phase flows is significant to different engineering systems such as chemical reactors and power plant and petrochemical and petroleum industry. One of the most industrial cases of two phase flow is two phase flow in vertical large pipes. In this paper in order to find two phase flow behavior along vertical large diameter pipes we simulate air inlets with different number of holes and different hole diameters in the same flow rate of air. In addition, flow characteristics such as cross-sectional void fraction and velocity and pressure were considered. To achieve this aim, main equations of flow have been developed for investigation of flow behavior in air-water two... 

The present work investigates the thermal performance of a five turn Open Loop Pulsating Heat Pipe (OLPHP). The effects of working fluid namely water and ferrofluid, heat input, ferrofluid concentration, charging ratio, and orientation will be considered. Experimental results show that using ferrofluids can enhance the thermal performance in comparison with the case of distilled water. In addition, applying a magnetic field on the OLPHP charged with ferrofluid reduces its thermal resistance. Variation of the ferrofluid concentration results in different thermal performance of the OLPHP. Best charging ratio for the distilled water and ferrofluid without magnetic field is 60 % in most of the...