Sharif Digital Repository

In this research, production of ferrite - martensite dual phase Steels with different martensite morphology was considered during transient liquid phase bonding of a low carbon steel. The steel was bonded using an iron base interlayer with melting point of 1443 K and 40 μm thickness. Bonding process carried out at 1473 K, under pressure of 0.5 MPa, at different holding time of 10, 20, 30 and 40 minutes. Microstructural studies of joint region showed that isothermal solidification completed at the bonding time of 40 minutes. Microstructure of joints made at the bonding time of 10, 20, and 30 minutes consists of two distinct region, athermal and isothermal solidified zones. Microstructure of... 

Graphene oxide (GO) nanosheets were hybridized with Fe3O4 nanoparticles (NPs) to form magnetic GO (MGO) and were further labeled by [68Ga]GaCl3 as a potential drug delivery system. Paper chromatography, Fourier transform infra red (FTIR) spectroscopy, low-angle X-ray diffraction (XRD), CHN and atomic force microscopy (AFM) were utilized to characterize the trinary composite ([68Ga]@MGO). Biological evaluations of the prepared nanocomposite were performed in normal Sprague Dawley rats and it was found to be a possible host for theranostic radiopharmaceuticals. The results showed that the grafting of Fe3O4 NPs on nanocomposite reduced the unwanted liver and spleen uptakes and increased the... 

Introduction: Artificial Intelligence (AI) represents a significant advancement in technology, and it is crucial for policymakers to incorporate AI thinking into policies and to fully explore, analyze and utilize massive data and conduct AI-related policies. AI has the potential to optimize healthcare financing systems. This study provides an overview of the AI application domains in healthcare financing. Method: We conducted a scoping review in six steps: formulating research questions, identifying relevant studies by conducting a comprehensive literature search using appropriate keywords, screening titles and abstracts for relevance, reviewing full texts of relevant articles, charting... 

In the present study, a special heat treatment cycle (step quenching) was used to produce a dual-phase (DP) microstructure in low carbon steel. By producing this DP microstructure, the mechanical properties of the investigated steel such as yield stress, tensile strength, and Vickers hardness were increased 14, 55, and 38%, respectively. In order to investigate the effect of heat treatment on formability of the steel, Nakazima forming test was applied and subsequently finite element base modeling was used to predict the outcome on forming limit diagrams. The results show that the DP microstructure also has a positive effect on formability. The results of finite element simulations are in a... 

Finite element analysis of creeping short fiber composites is carried out in the second stage creep with application in microelectronic and optoelectronic/photonic devices. Prediction of the creep behavior is very significant for designing the optoelectronic and photonic composites with optical fibers. Study on the creep behavior is necessary for failure, fracture, fatigue, and creep resistance of the optoelectronic/photonic composites. The creep behavior of the short fiber composites is estimated by FEM. Study on the creep behavior is necessary for defect analysis and creep resistance of the short fiber composites. In this research work, prediction of the creep behavior of the short fiber... 

FEM study is carried out for predicting the behavior of the short fiber composites in the steady state creep with application in optoelectronic and photonic devices. The study on the creep behavior is necessary in order for failure, fracture, fatigue, and creep resistance of the short fiber composites. In this article, the creep behavior of the short fiber composite is predicted under tensile axial loading by the numerical method. One of the significant applications of the work is in the short fiber composite designing and optimizing. Also, the available experimental results [10] are used for the FEM simulation  

In this article, we investigated the effect of martensite morphology on the mechanical properties and formability of dual phase steels. At first, three heat treatment cycles were subjected to a low-carbon steel to produce ferrite–martensite microstructure with martensite morphology of blocky-shaped, continuous, and fibrous. Tensile tests were then carried out so as to study mechanical properties, particularly the strength and strain hardening behavior of dual phase steels. In order to study the formability of dual phase samples, Forming Limit Diagram was obtained experimentally and numerically. Experimental forming limit diagram was obtained using Nakazima forming test, while Finite Element... 

In this article, we investigated the effect of martensite morphology on the mechanical properties and formability of dual phase steels. At first, three heat treatment cycles were subjected to a low-carbon steel to produce ferrite–martensite microstructure with martensite morphology of blocky-shaped, continuous, and fibrous. Tensile tests were then carried out so as to study mechanical properties, particularly the strength and strain hardening behavior of dual phase steels. In order to study the formability of dual phase samples, Forming Limit Diagram was obtained experimentally and numerically. Experimental forming limit diagram was obtained using Nakazima forming test, while Finite Element... 

In the last two decades, quantum dots nanomaterials have garnered a great deal of scientific interest because of their unique properties. Quantum dots (QDs) are inorganic fluorescent nanocrystals in the size range between 1 and 20 nm. Due to their structural properties, they possess distinctive properties and behave in different way from crystals in macro scale, in many branches of human life. Cadmium telluride quantum dots (CdTe QDs) were labeled with 68Ga radio nuclide for fast in vivo targeting and coincidence imaging of tumors. Using instant paper chromatography, the physicochemical properties of the Cadmium telluride quantum dots labeled with 68Ga NPs (68Ga@ CdTe QDs) were found high... 

This research reports the preparation and examination of Cadmium Telluride (CdTe) Quantum Dots and doping CdTe QDs with Europium (Eu), Gadolinium (Gd), and Manganese (Mn) prepared in aqueous solution using TGA as a capping agent. Magnetic QDs (MQDs) are important agents for fluorescence (FL) /magnetic resonance (MR) dual-modal imaging due to their excellent optical and magnetic properties. Herein, the chemical bonds, structural, fluorescence, and magnetized properties of CdTe QDs and effect of Mn, Eu, and Gd ions doping on their properties were examined by X-ray powder diffraction (XRD), high-resolution transmission electron microscopy (HRTM), Energy-dispersive X-ray spectroscopy (EDX),... 

Graphene oxide (GO) sheets functionalized by aminopropylsilyl groups (8.0 wt.%) were labeled by 198,199Au nanoparticle radioisotopes (obtained through reduction of HAuCl4 in sodium citrate solution followed by thermal neutron irradiation) for fast in vivo targeting and SPECT imaging (high purity germanium-spectrometry) of tumors. Using instant thin layer chromatography method, the physicochemical properties of the amino-functionalized GO sheets labeled by 198,199Au NPs (198,199Au@AF-GO) were found to be highly stable enough in organic phases, e.g. a human serum, to be reliably used in bioapplications. In vivo biodistribution of the 198,199Au@AF-GO composite was investigated in rats bearing... 

A novel intelligent semi-active control system for an eleven degrees of freedom passenger car's suspension system using magnetorheological (MR) damper with neuro-fuzzy (NF) control strategy to enhance desired suspension performance is proposed. In comparison with earlier studies, an improvement in problem modeling is made. The proposed method consists of two parts: a fuzzy control strategy to establish an efficient controller to improve ride comfort and road handling (RCH) and an inverse mapping model to estimate the force needed for a semi-active damper. The fuzzy logic rules are extracted based on Sugeno inference engine. The inverse mapping model is based on an artificial neural network... 

Using CNG as an additive for gasoline is a proper choice due to higher octane number of CNG enriched gasoline with respect to that of gasoline. As a result, it is possible to use gasoline with lower octane number in the engine. This would also mean the increase of compression ratio in SI engines resulting in higher performance and lower gasoline consumption. Over the years, the use of simulation codes to model the thermodynamic cycle of an internal combustion engine have developed tools for more efficient engine designs and fuel combustion. In this study, a thermodynamic cycle simulation of a conventional four-stroke spark-ignition engine has been developed. The model is used to study the... 

With the declining energy resources and increase of pollutant emissions, a great deal of efforts has been focused on the development of alternatives for fossil fuels. One of the promising alternative fuels to gasoline in the internal combustion engine is natural gas [1-5]. The application of natural gas in current internal combustion engines is realistic due to its many benefits. The higher thermal efficiency due to the higher octane value and lower exhaust emissions including CO2 as a result of the lower carbon to hydrogen ratio of the fuel are the two important feature of using CNG as an alternative fuel. It is well known that computer simulation codes are valuable economically as a cost... 

Gaining insight into possible vibratory responses of dynamical systems around their stable equilibria is an essential step, which must be taken before their design and application. The results of such a study can significantly help prevent instability in closed-loop stabilized systems by avoiding the excitation of the system in the neighborhood of its resonance. This paper investigates nonlinear oscillations of a rotary inverted pendulum (RIP) with a full-state feedback controller. Lagrange’s equations are employed to derive an accurate 2-DoF mathematical model, whose parameter values are extracted by both the measurement and 3D modeling of the real system components. Although the governing... 

A suction-controlled ring device has been developed to continuously measure the coefficient of lateral soil pressure in deformable unsaturated soil samples from the at-rest to the active condition under application of increasing vertical pressure and controlled matric suction. The device incorporates a thin aluminum specimen ring equipped with horizontal strain gages for recording the lateral soil strains. In addition, a sensor recording water volume changes is utilized to continuously monitor the degree of saturation of the soil sample during tests. The matric suction within the soil texture is controlled using the axis translation technique. In order to verify the performance of the ring... 

We introduce a new smooth, non-toxic, biocompatible method for cross-linking of gum tragacanth (GT), a polysaccharide of natural origin, in order to serve as a new supporting matrix for immobilization systems. The modified gum is used as a matrix for the catalysis of the conversion of benzyl penicillin to 6-aminopenicillanic acid (6-APA) by means of Escherichia coli ATCC11105 with penicillin G acylase (PGA) activity. The results show that GT beads can not only serve as a proper matrix for immobilization, but show enhanced hydrolysis rate and stability compared to other immobilization systems used for this reaction. This signifies the potential of GT as a biocompatible matrix for... 

The Class-E power amplifier has been widely studied and formulated in the literature. Although the majority of reported inductive coupling wireless power transfer (WPT) systems use a class-E power amplifier for driving the primary coil, still there is a lack of a comprehensive study on class-E circuit dedicated to WPT, providing a set of closed form design equations for proper class-E operation. This paper presents the required design equations needed to design a 'true' class-E circuit for WPT applications. Equations for the series-tuned secondary coil WPT system are presented, as well as two different design procedures for the parallel-tuned secondary coil. The derived equations have been... 

Pole Side Impact Tes is one out of three crash tests described by Euro NCAP standard for star rating of a vehicle and is required for assessing the Adult Occupant Protection. In this paper the goal is to determine the crashworthiness of side doors and B pillar in a Pole Side Impact Test based on Euro New Car Assessment Program (Euro-NCAP) using computer and simulation method. In this matter, a vehicle model has been prepared and meshed using Hypermesh and CATIA. The velocity of 29 km/h has been assigned to the vehicle which was on top of a cart while the pole has been assigned as a rigid static object based on Euro NCAP requirements specifically. Results show that different amounts of energy...