Sharif Digital Repository

In this study, fatigue, corrosion fatigue and electrochemical behaviors of butt-welded A106-B steel pipes were investigated. These pipes were subjected to mechanical and thermal cyclic stresses due to the internal pressure fluctuations and cooling-heating cycles. Residual stress measurements were carried out for three different depths through the thickness and were correlated to the microstructural observations and microhardness measurements. Results showed that the maximum tensile residual stresses existed at the boundary of weld metal and base metal because of the contraction-expansion effects resulting from phase transformations and cooling rate differences. Fatigue fractures occurred at... 

The present research was aimed at simultaneous increase in strength and fracture energy of friction stir spot weld of Al-5083 alloy via reinforcing by Fe3O4 nanoparticles. Compared to non-reinforced welds, failure load and fracture energy of reinforced welds increased up to ∼115 and 560%, respectively. These findings were discussed in the light of grain refinement as well as considerable increase in hardness of fracture location due to the presence of sub-micron and nano reinforcing particles (RPs). Fe3O4 nanoparticles were transformed to Al–Fe intermetallics due to their small size and heat generated during the welding process. The stir zone of reinforced welds consisted of three different... 

The effect of the rotational speed and dwell time on the joint interface microstructure and tensile-shear strength of friction stir spot welded Al-5083 aluminum/St-12 steel alloy sheets was investigated. Joining of the sheets was performed using an alternative friction stir spot welding (FSSW) process in which the welding tool tip did not penetrate into the lower steel sheet. Rotational speeds of 900 and 1100 rpm were applied in association with the dwell times of 5 to 15 s to weld the samples. Thermal history was recorded during the joining process. Interfacial microstructure, formation of intermetallic compounds (IMCs) at the joint interface and the fracture locations were studied using... 

There has always been a question about which condition results in superior mechanical properties in friction stir spot welds: (i) when the tool tip penetrates into the lower sheet or (ii) when the tool tip does not touch it. Given the question, the effects of the tool penetration depth were investigated on the microstructure and mechanical behaviour of dissimilar Al-5083/St-12 joints produced by friction stir spot welding (FSSW). Two different processes named as non-penetrating and penetrating FSSW were used. Optical and scanning electron microscopes as well as microhardness and tensile-shear tests were utilised to examine the obtained joints. The results showed that the penetrating process... 

The present research aims at depositing molybdenum on stainless steel substrate using dense plasma focus (DPF) device. The varying parameter was the angular position of substrate surface from the anode tip. The deposited layers were characterized using various analyses such as X-ray diffraction (XRD), scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), atomic force microscopy (AFM), and microhardness measurements. Microstructural observations revealed that the deposited coatings had rough surfaces containing holes as well as a stripe-featured structure covering the whole surface including the interior regions of the holes and the regions among them.... 

Joining of Al-5083 alloy sheet to St-12 steel sheet was performed using a new friction stir spot welding (FSSW) technique in which the tool pin tip did not enter lower steel sheet. Effect of dwell time on the microstructure and mechanical properties of the joints was studied by various methods including microhardness measurements, shear test, stereo and light microscopy as well as scanning and transmission electron microscopy (SEM and TEM). Results indicated that compared to the conventional FSSW process, stronger joints can be achieved by this FSSW technique. Cross-sectional observation of the failed specimens indicated the occurrence of final fracture from the circumference of the tool pin... 

In vivo dose-dependent effects of nanoscale graphene oxide (NGO) sheets on reproduction capability of Balb/C mice were investigated. Biodistribution study of the NGO sheets (intravenously injected into male mice at dose of ∼2000 μg/mL or 4 mg/kg of body weight) showed a high graphene uptake in testis. Hence, in vivo effects of the NGO sheets on important characteristics of spermatozoa (including their viability, morphology, kinetics, DNA damage and chromosomal aberration) were evaluated. Significant in vivo effects was found at the injected concentrations ≥200 μg/mL after (e.g., ∼45% reduction in sperm viability and motility at 2000 μg/mL). Observation of remarkable DNA fragmentations and... 

Asian red ginseng was used for green reduction of chemically exfoliated graphene oxide (GO) into reduced graphene oxide (rGO). The reduction level and electrical conductivity of the ginseng-rGO sheets were comparable to those of hydrazine-rGO ones. Reduction by ginseng resulted in repairing the sp 2 graphitic structure of the rGO, while hydrazine-rGO showed more defects and/or smaller aromatic domains. The ginseng-rGO sheets presented a better stability against aggregation than the hydrazine-rGO ones in an aqueous suspension. Whilst the hydrophobic hydrazine-rGO films exhibited no toxicity against human neural stem cells (hNSCs), the hydrophilic GO and ginseng-rGO films (as more... 

Vigorous debates have taken place within and between many countries about regulatory policy regimes covering the assessment and approval of genetically modified (GM) crops. In Iran, a very vigorous and hotly contested policy debate concerning legislation covering GM crops occurred between 2004 and 2009, but it was confined within government circles with almost no public discussion. This paper analyses the Iranian policy-making process in the period 2006-9. It explains how and why a stalemate arose in disputes between ministries and departments. The chosen analytical framework draws mainly on the regulation of technological risks and the analysis of public policy-making. It deploys the... 

A μ-way latin trade of volume s is a set of μ partial latin rectangles (of inconsequential size) containing exactly the same s filled cells, such that if cell (i, j) is filled, it contains a different entry in each of the μ partial latin rectangles, and such that row i in each of the μ partial latin rectangles contains, set-wise, the same symbols and column j, likewise. In this paper we show that all μ-way latin trades with sufficiently large volumes exist, and state some theorems on the non-existence of μ-way latin trades of certain volumes. We also find the set of possible volumes (that is, the volume spectrum) of μ-way latin trades for μ = 4 and 5. (The case μ = 2 was dealt with by Fu,... 

The set of integers k for which there exist three latin squares of order n having precisely k cells identical, with their remaining n2 -k cells different in all three latin squares, denoted by I3[n], is determined here for all orders n. In particular, it is shown that I3[n] = {0,.,n2 -15}U [n2 - 12,n2-9,n2], for n ≫8. ©2002 Eisevier Science B.V. All rights reserved  

Coronary angiography is a vital instrument to detect the prevailing of vascular diseases, and accurate vascular segmentation acts a crucial role for proper quantitative analysis of the vascular tree morphological features. Level set methods are popular for segmenting the coronary arteries, but their performance is related to suitable start-up and optimum setting of regulating parameters, essentially done manually. This research presents a novel fuzzy level set procedure with the objective of segmentation of the coronary artery tree in 2-D X-ray angiography as automatically. It is clever to clearly develop from the early segmentation with spatial fuzzy grouping. The adjusting parameters of... 

Visual attributes are great means of describing images or scenes, in a way both humans and computers understand. In order to establish a correspondence between images and to be able to compare the strength of each property between images, relative attributes were introduced. However, since their introduction, hand-crafted and engineered features were used to learn increasingly complex models for the problem of relative attributes. This limits the applicability of those methods for more realistic cases. We introduce a deep neural network architecture for the task of relative attribute prediction. A convolutional neural network (ConvNet) is adopted to learn the features by including an... 

We present the first public code for the calculation of the astrometric centroid shift occurring during microlensing events. The computation is based on the contour integration scheme and covers single and binary lensing of finite sources with arbitrary limb darkening profiles. This allows for general detailed investigations of the impact of finite source size in astrometric binary microlensing. The new code is embedded in version 3.0 of vbbinarylensing, which offers a powerful computational tool for extensive studies of microlensing data from current surveys and future space missions. © 2021 The Author(s) Published by Oxford University Press on behalf of Royal Astronomical Society  

The possibility of real-time tuning of optical devices has attracted a lot of interest over the last decade. At the same time, coming up with simple lithography-free structures has always been a challenge in the design of large-area compatible devices. In this work, we present the concept and the sample design of an electrically tunable, lithography-free, ultra-thin transmission-mode color filter, the spectrum of which continuously covers the whole visible region. A simple Metal-Insulator-Metal (MIM) cavity configuration is used. It is shown that using the electro-optic dielectric material of 4-dimethyl-amino-N-methyl-4-stilbazoliumtosylate (DAST) as the dielectric layer in this... 

Magnetic flux leakage is the most widely used method for oil and gas pipeline non destructive testing. The saturation level of the sample under test has a significant effect on its efficiency; therefore, the magnetizing yoke requires an elaborate design. The finite element method is the conventional approach used for this purpose, but it is very time consuming. In this article, a neuro-fuzzy method is presented to model the behavior of the magnetizing yoke. Modeling a few different designs with the finite element method and using the results for training the neuro-fuzzy model eradicates the necessity of modeling a huge number of designs with the finite element method. The acquired... 

The problem of finding necessary and sufficient conditions to decompose a complete tripartite graph K(r, s, t) into 5-cycles was first considered by Mahmoodian and Mirzakhani (1995). They stated some necessary conditions and conjectured that these conditions are also sufficient. Since then, many cases of the problem have been solved by various authors; however the case when the partite sets r ≤ s ≤ t have odd and distinct sizes remains open. A necessary condition is t ≤ 3r. Billington and Cavenagh (2011) have shown that when r, s, and t are all odd and r ≤ s ≤ t ≤ κr, where κ ≈ 1.0806, then the conjectured necessary conditions for decomposing are also sufficient. We extend this result... 

Graphene oxide nanoplatelets (GONPs) with extremely sharp edges (lateral dimensions ∼20-200 nm and thicknesses <2 nm) were applied in extraction of the overexpressed guanine synthesized in the cytoplasm of leukemia cells. The blood serums containing the extracted guanine were used in differential pulse voltammetry (DPV) with reduced graphene oxide nanowall (rGONW) electrodes to develop fast and ultra-sensitive electrochemical detection of leukemia cells at leukemia fractions (LFs) of ∼10-11 (as the lower detection limit). The stability of the DPV signals obtained by oxidation of the extracted guanine on the rGONWs was studied after 20 cycles. Without the guanine extraction, the DPV peaks... 

Specific and sensitive electroanalysis of blood-circulating protein cancer biomarkers is often complicated by interference from serum proteins nonspecifically adsorbing at the biosensing interface and masking specific reactions of interest. Here, we have developed an electrocatalytically amplified assay for specific and sensitive analysis of human epidermal growth factor receptor-2 (HER-2/neu, a protein cancer biomarker over-expressed in breast cancers) that allows us to avoid both the interference from bovine serum albumin (BSA) and electrocatalytic amplification of the signal stemming from the specific aptamer−HER-2/neu binding. A HER-2/neu-specific thiolated aptamer sequence was...