Sharif Digital Repository

Tungsten oxide nanoparticles were fabricated by a pulsed laser ablation method in deionized water using the first harmonic of a Nd:YAG laser (λ = 1064 nm) at three different laser pulse energies (E1 = 160, E2 = 370 and E3 = 500 mJ/pulse), respectively. The aim is to investigate the effect of laser pulse energy on the size distribution and gasochromic property of colloidal nanoparticles. The products were characterized by dynamic light scattering (DLS), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and UV-Vis spectroscopy. The results indicated that WO 3 nanoparticles were formed. After ablation, a 0.2 g/l PdCl 2 solution was added to activate the solution against... 

In this letter a simple procedure to synthesize sodium tungsten oxide nano-thick plates from WO 3 films has been reported. WO 3 films were grown by pulsed-laser deposition method and then heat treated at temperatures up to 560 °C and times up to 120 min. Slide glass was used as both substrate and sodium source simultaneously. XRD analysis revealed presence of an amorphous structure for as-deposited WO 3 films. On the other hand, XRD showed formation of a monoclinic WO 3 structure with annealing in lower temperatures and a triclinic Na 0.5WO 3.25 structure with annealing at higher temperatures. Intensity of the triclinic phase peaks enhanced drastically by rising annealing temperature and... 

In this study, tungsten oxide films were synthesized by pulsed laser deposition (PLD) method. The as-deposited films were annealed at a temperature of 250 and 350°C in air for 1 h. The surface morphology, microstructure, crystalline phase and chemical composition of the as-prepared and annealed films were characterized by SEM, XRD and XPS techniques, respectively. Deposition of Pd nanoparticles onto the tungsten oxide surface was performed by hydrogen reduction of a drop-drying PdCl 2 solution onto a WO 3 surface at 60°C. The influence of the annealing temperature on microstructure and gasochromic performance as well as the effect of operating temperature is presented in this work. Results... 

Nowadays, gasochromic Pd/WO3 coatings as optically switchable materials during H2 absorption have become more interesting due to their novel applications in smart windows and gas sensor devices. In this study, WO3 films were fabricated by Pulsed Laser Deposition (PLD) on glass substrates. Using an electroless method, Pd nanoparticles were deposited on the surface of the produced films. The effect of Pd growth time on coloring/bleaching rate was studied for different submerging times (1, 2, 5, 10, 15, 20 and 40 min). The best coloring/bleaching velocity was attained with a growth time of 2 min. The effect of growing time and growth feature of Pd particles was further studied using Scanning... 

In this study, tungsten oxide films were deposited by pulsed-laser deposition (PLD) technique. The as-deposited films were annealed at 250 °C in air for 1 h. The surface morphology, microstructure, crystalline phase, and chemical composition of the films were characterized by SEM, XRD and XPS techniques. Pt nanoparticles were deposited onto the tungsten oxide films through a two-step process. First of all, a layer of PtCl2 was coated on the WO3 surface by drop-drying the PtCl2 solution onto the WO3 surface at 60 °C. Consequently, the reduction of the PtCl2 into the metallic Pt nanoparticles was performed at 200 °C. In this study, the effect of the temperature during hydrogen reduction of... 

In this study, tungsten oxide nanoparticles were fabricated by pulsed laser ablation (PLA) of tungsten target using the first harmonic of a Nd:YAG laser (1064 nm) in deionized water. After ablation, a 0.2 g/lit PdCl 2 solution was added to activate the solution against the hydrogen gas. Dynamic light scattering and X-ray photoelectron spectroscopy were used to measure the average size and the surface chemical composition of the synthesized nanoparticles, respectively. The aim is to investigate the influence of hydrogen exposure time on colouration process of colloidal nanoparticles. According to optical measurements, hydrogen bubbling into the produced colloidal Pd-WO 3 led to formation of... 

For the 4th IUPAP International Conference of Women in Physics, we report on activities in science and engineering in Iran, and conditions for women in physics, in the three years since the 3rd IUPAP International Conference of Women in Physics was held in 2008. Iran has made prominent advancements and astonishing progress in laser technology, biotechnology, nanotechnology, genetics, computer software and hardware, and robotics. Iranian scientists have been very productive in several experimental fields, such as pharmaceutical, organic, and polymer chemistry. Conditions for women in physics have improved greatly in recent years. A project to improve the environment for learning physics, and... 

Micro and nanotechnology can potentially revolutionize drug delivery systems. Novel microfluidic systems have been employed for the cell culture applications and drug delivery by micro and nanocarriers. Cells in the microchannels are under static and dynamic flow perfusion of culture media that provides nutrition and removes waste from the cells. This exerts hydrostatic and hydrodynamic forces on the cells. These forces can considerably affect the functions of the living cells. In this paper, we simulated the flow of air, culture medium, and the particle transport and deposition in the microchannels under different angles of connection inlet. It was found that the shear stress induced by the... 

Thin porous membranes are important components in a microfluidic device, serving as separators, filters, and scaffolds for cell culture. However, the fabrication and the integration of these membranes possess many challenges, which restrict their widespread applications. This paper reports a facile technique to fabricate robust membrane-embedded microfluidic devices. We integrated an electrospun membrane into a polydimethylsiloxane (PDMS) device using the simple plasma-activated bonding technique. To increase the flexibility of the membrane and to address the leakage problem, the electrospun membrane was fabricated with the highest weight ratio of PDMS to polymethylmethacrylate (i.e., 6:1... 

Microfluidic devices have been widely used for biological and cellular studies. Microbioreactors for three-dimensional (3D) multicellular spheroid culture are now considered as the next generation in in vitro diagnostic tools. The feasibility of using 3D cell aggregates to form multicellular spheroids in a microbioreactor with U-shaped barriers has been demonstrated experimentally. A barrier array is an alternative to commonly used microwell traps. The present study investigates oxygen and glucose concentration distributions as key parameters in a U-shaped array microbioreactor using finite element simulation. The effect of spheroid diameter, inlet concentration and flow rate of the medium... 

Dielectrophoresis is a robust approach for manipulating bioparticles in microfluidic devices. In recent years, many groups have developed dielectrophoresis-based microfluidic systems for separation and concentration of various types of bioparticles, where the gradient of the electric field causes dielectrophoresis force acting on the suspended particles. Enhancing the gradient of the electric field with three-dimensional (3D) electrodes can significantly improve the efficiency of the system. Implementing planar electrodes in a 3D arrangement is a simple option to form a 3D-electrode configuration. This paper reports the development of a novel dielectrophoretic microfluidic system for... 

In this study, effectiveness of non-ionic block copolymers such as Lugalvan BNO12 and Triton X series (Triton X100 & Triton X405) has been reported for graphene dispersion in aqueous solutions. Stability of the aqueous graphene dispersions is investigated using UV–visible spectroscopy, Rheological, and Conductivity studies. Adsorption isotherms are constructed to determine the amount of polymers adsorbed on the surface of graphene by the spectroscopic analysis. Lugalvan BNO12 has been found to be adsorbed in higher amounts on the graphene surface compared to the Triton X series polymers. Thermogravimetric analysis (TGA) and Fourier Transform Infrared (FTIR) Spectroscopy investigations... 

Service-oriented computing has emerged as a new software development paradigm that enables implementation of Web accessible software systems that are composed of distributed services which interact with each other via exchanging messages. Modeling and analysis of interactions among services is a crucial problem in this domain. Interactions among a set of services that participate in a service composition can be described from a global point of view as a choreography. Choreographies can be specified using specification languages such as Web Services Choreography Description Language (WS-CDL) and visualized using graphical formalisms such as collaboration diagrams. In this paper, we present an... 

We investigate how the inverse degree index of graphs depends on their cyclomatic number. In particular, we provide sharp lower bounds on the inverse degree index over all graphs on a given number of vertices with a given cyclomatic number. We also deduce some structural properties of extremal graphs. Some open questions regarding the upper bound over the same class of graphs are discussed and some possible further developments are indicated. © 2023, University of Nis. All rights reserved  

This paper presents the measurements results of simulated partial discharge propagation on a compact three phase XLPE cable, and shows how the high frequency signal on one phase of the cable is induced on the other two phases. A frequency dependent three phase cable model is employed to simulate this phenomena. © 2008 Australasian Universities Power Engineering Conference (AUPEC'08)  

This study was aimed at evaluating the effects of alkali activator solution and utilization of silica fume (SF) on durability and microstructural characteristics of alkali-activated ground granulated blast furnace slag (GGBFS) pastes. The pastes were activated with sodium silicate (SS) blended with NaOH (SH) solution with molar concentrations of 8 M, 12 M, and 16 M and SS:SH ratios of 1.0, 2.5, and 4.0. The same mixes were prepared with SF as partial replacement of GGBFS at a dosage of 10% by weight. The initial and final water absorption as well as the electrical resistivity of the specimens were measured. The optimal paste fabricated with 12 M NaOH solution and SS:SH ratio of 2.5 showed... 

A microfluidic system provides an excellent platform for cellular studies. Most importantly, a three-dimensional (3D) cell culture model reconstructs more accurately the in vivo microenvironment of tissue. Accordingly, microfluidic 3D cell culture devices could be ideal candidates for in vitro cell culture platforms. In this paper, two types of 3D cellular aggregates, i.e., toroid and spheroid, are numerically studied. The studies are carried out for microfluidic systems containing U-shaped barrier as well as microwell structure. For the first time, we obtain oxygen and glucose concentration distributions inside a toroid aggregate as well as the shear stress on its surface and compare its... 

Microfluidic cell culture platforms are ideal candidates for modeling the native tumor microenvironment because they can precisely reconstruct in vivo cellular behavior. Moreover, mathematical modeling of tumor growth can pave the way toward description and prediction of growth pattern as well as improving cancer treatment. In this study, a modified mathematical model based on concentration distribution is applied to tumor growth in both conventional static culture and dynamic microfluidic cell culture systems. Apoptosis and necrosis mechanisms are considered as the main inhibitory factors in the model, while tumor growth rate and nutrient consumption rate are modified in both quiescent and...