Sharif Digital Repository

In this paper effects of material properties estimations, used for particulate reinforced composites, on the thermo-mechanical response of functionally graded sphere and cylinder are presented. A numerical solution for an arbitrary material gradation is obtained for each geometry independently. With this assumption, the governing partial differential equations are reduced to an ordinary differential equation in each geometry. The thermo-elastic solution for hollow sphere is derived using spherical symmetry. However, plane strain and axial symmetry are assumed for solving hollow cylinder. In the numerical method, radial domain is divided into some finite sub-domains and material properties... 

Focused on the assessment of the diphenhydramine hydrochloride (DPH) capabilities as an alternative to conventional and harmful industrial corrosion inhibitors, electrochemical techniques were employed. The optimum concentration of 1000 ppm was determined by molecular simulation and validated through electrochemical experiments. The results acquired from the electrochemical impedance spectroscopy (EIS) study showed that DPH at a concentration of 1000 ppm has a corrosion efficiency of 91.43% after 6 h immersion. The DPH molecules' orientation on the surface was assessed based on EIS predicting horizontal adsorption on the surface. Molecular simulations were done to explore the adsorption... 

Graphene-tungsten oxide composite thin films with sheetlike surface morphology were fabricated and applied in photoinactivation of viruses under visible light irradiation. Using X-ray photoelectron spectroscopy, it was found that the chemically exfoliated graphene oxide sheets incorporated in the tungsten oxide film reduced through a visible light photocatalytic reduction. In addition, annealing the films at 450 °C in air resulted in formation of W-C and W-O-C bonds to obtain graphene-tungsten oxide composite films. The composite films fabricated by this method showed an excellent visible light photocatalytic performance in photoinactivation of bacteriophage MS2 viruses, as compared to... 

In this paper a semi-analytical method is developed to analyze functionally graded cylindrical panels. In this method, the radial domain is divided into some finite sub-domains and the material properties are assumed to be constant in each subdomain. Imposing the continuity conditions at the interface of the adjacent sub-domains, together with the global boundary conditions, a set of linear algebraic equations are derived. Solving the linear algebraic equations, the elastic response for the thick-walled FG cylindrical panel is obtained. The method can be used for all material properties variations but in present study, material properties are assumed vary with Mori-Tanaka estimation. Results... 

A low-power wide-range CMOS temperature sensor architecture is proposed for RFID and Sensor Networks based on temperature-to-frequency conversion using supply voltage controlled sub-threshold ring oscillator. The principles of operation are investigated and proved via simulation results. Most errors are canceled out by this ratio-metric design. An inaccuracy of -0.84°C to +0.34°C occurs over a range of -40°C to 80°C after using a novel in-field digital two-point calibration. The entire sensor consumes less than 93nW to 305nW over the temperature range and can be digitally reconfigured for setting sample rate and resolution in a tradeoff. © 2016 IEEE  

In this research, different coating methods of polyaniline (PANI) on the anode electrodes and their performance in microbial fuel cells (MFCs) were investigated. The performance of systems in a discontinuous state was studied using the high energy content dairy industry wastewater. The phase enrichment assessment was conducted under open circuit potential (OCP) and the performance of MFCs coated with PANI through three methods was evaluated via chemical oxygen demand (COD), polarization, power density, energy coulombic efficiency (ECE), coulombic efficiency (CE), and potential efficiency (PE) values. The results showed the maximum value for the power density of 28Wm-3, CE of 17%, and COD of... 

In this paper, static behavior and pull-in of micro tweezers is studied. The micro tweezer is modelled as two cantilever beams. Static behavior of the micro tweezer under the effect of electrostatic actuation is modelled using the Euler-Bernoulli beam theory. In order to capture size effects on the behavior of micro tweezers, modified couple stress theory is utilized. It is shown when the voltage between two electrodes increased from some specific value, micro beams adhere to each other and it is observed that the pull-in voltage predicted by the modified couple stress theory considerably differs with that of the classical theory of elasticity. Results of this paper can be used for accurate... 

Despite widespread use of SRAM-based reconfigurable devices (SRDs) in mainstream applications, their usage has been very limited in enterprise and safety-critical applications due to SRAM susceptibility to soft errors. Previous mitigation techniques to protect SRDs impose significant area and power overheads. Additionally, they suffer from susceptibility of configuration bits to multiple bit upsets (MBUs). In this paper, we present a highly available fault-tolerant architecture to protect SRD-based designs against MBUs in both configuration and user bits. In the proposed architecture, the entire design is duplicated with respect to the relative locations of logic blocks within the SRD and... 

Molybdenum disulfide (MoS2), a 2D layered structure, because of its unique properties has widely attracted many researchers. In this study, by employing physical and chemical methods, not only layers of MoS2 have been intercalated, but also their surface properties enhanced. Low-dimensional and potential properties of intercalated MoS2 nanosheets are the aim of many researches. Here, we report a novel four step method to intercalate the layers of MoS2 nanosheets successfully using acid treatment, sonication, oxidization and thermal shocking. The other goal in this study is to evaluate the cation exchange ability and anticorrosion performance of the Ce3+ doped MoS2 nanosheets. The... 

In this study, effects of dried saffron purple petals (SPP) powder were examined on the rheological, fluid loss, and corrosion inhibition properties of bentonite-based drilling fluids. Drilling fluids containing different amounts of the SPP powder were prepared and their rheological behavior was investigated via the rotary viscometry and rheometric mechanical spectroscopy (RMS). Rotary viscometer results were fitted with Power-law, Bingham plastic, and Herschel-Bulkley models and the obtained data were compared with that of the base mud. All models fitted the rotary viscometer data with the determination coefficients higher than 0.93. The presence of 3 wt% of the SSP in the fluid... 

Blotches are the common artifacts in degraded motion picture sequences. They are usually caused by placing dust and dirt on film surfaces as well as abrasion of film materials. Blotches are seen as dark and bright flashes spreading through the frames, randomly. The spike detection index (SDIa) method is the simplest approach used to detect these artifacts. However, when the motion vectors are not precise enough in some points they might be declared as blotches too. This situation can also occur in areas containing a high level of noise. To overcome these difficulties, two post-processing methods are proposed in this paper. In the first method, the edge points are first omitted from the set... 

Transformation-induced plasticity (TRIP) steel resistance spot welds are delicate to low-energy interfacial failure via crack propagation through martensitic fusion zone during cross-tension (CT) loading. This paper addresses the effect of three different types of in situ postweld heat treatment (PWHT) on the mechanical properties of TRIP steel resistance spot welds. Depending on the post weld second pulse current level, three different strengthening mechanisms were found including (i) martensite tempering with reduced hardness, (ii) refining of martensite packets with improved toughness and (iii) nugget re-melting/enlargement combined with possible reduction of grain boundary impurity... 

The high aspect ratio and unique thermal and electrical characteristics of carbon nanofiber (CNF) made it an ideal physical barrier against the penetration of corrosive ions. However, the poor compatibility of the CNF with the polymer matrix and the lack of active corrosion inhibitors are the key limitations of this nanomaterial, resulting in short-term anti-corrosion resistance. An intelligent self-healing epoxy (EP) coating, including CNF modified with a polydopamine (PDA)-La3+ complex, was successfully fabricated to overcome these issues. Electrochemical impedance spectroscopy (EIS) evaluation implied that mild steel (MS) submerged in a 3.5 wt % NaCl solution containing the CNF-PDA-La... 

In this study, poly (vinylidene fluoride) PVDF/Starch nanofibers with a great potential for tissue engineering applications have been investigated. The electrospun nanofibers were formed by the electrospinning of the PVDF/Starch solutions in various ratios of PVDF to Starch. Characterizations of PVDF/Starch nanofiber were performed using rheometric mechanical spectroscopy (RMS), field emission scanning electron microscope (FE-SEM) and tensile test. The results showed that the addition of more Starch into the PVDF solution increased the viscosity of the prepared PVDF/Starch solutions. In addition, the mechanical properties of PVDF enhanced in the presence of Starch due to the higher... 

The evaluation of multigroup constants in reactor calculations depends on several parameters. One of these parameters is the Dancoff factor which is used for calculating the resonance integral and flux depression in the resonance region in heterogeneous systems. In the current paper, a computer program (MCDAN-3D) is developed for calculating three dimensional black and gray Dancoff coefficients, based on Monte Carlo, escape probability and neutron free flight methods. The developed program is capable to calculate the Dancoff factor for an arbitrary arrangement of fuel and moderator pebbles. Moreover this program can simulate fuels with homogeneous and heterogeneous compositions. It might... 

Evaluation of multigroup constants in reactor calculations depends on several parameters, the Dancoff factor amid them is used for calculation of the resonance integral as well as flux depression in the resonance region in the heterogeneous systems. This paper focuses on the computer program (MCDAN-3D) developed for calculation of the multigroup black and gray Dancoff factor in three dimensional geometry based on Monte Carlo and escape probability methods. The developed program is capable to calculate the Dancoff factor for an arbitrary arrangement of fuel rods with different cylindrical fuel dimensions and control rods with various lengths inserted in the reactor core. The initiative...