Sharif Digital Repository

In this paper, a wideband, circularly polarized patch antenna is proposed that leverages the unidirectional resonant modes of a circular patch mounted on top of a grounded dielectric-ferrite substrate. The proposed antenna is fed via the proximity coupling method and several parasitically coupled patches are placed on a dielectric superstrate to enhance the impedance bandwidth of the antenna. The resonant modes of the structure rotate only in the clockwise or counter clockwise directions. In the frequency range where the effective permeability of the ferrite layer is negative, the resonance frequencies of these modes differ significantly, which produces a large axial ratio (AR) bandwidth.... 

We propose a wideband circularly polarized antenna that consists of a metallic patch and some parasitically coupled elements mounted on a grounded dielectric-ferrite substrate. The metallic patch is fed by a proximity-coupled feed line placed between the ferrite and the dielectric layers. The parasitically coupled elements are included to improve the impedance bandwidth of antenna and are excited through the metallic patch. The antenna utilizes the resonant modes of the structure, which rotate only in the clockwise or counter-clockwise direction. A semi-Analytical solution based on the magnetic wall approximation shows that the resonance frequencies of the clock-and counter-clockwise... 

We propose an accurate analytical model for a circularly polarized antenna comprising a normally magnetized, grounded ferrite disk with a metalized top surface. The antenna is assumed to be excited by a conventional current probe. In the case of a thin ferrite disk, the electromagnetic fields of the dominant mode of the antenna do not vary in the direction normal to the disk. However, with increasing thickness of the ferrite disk, higher order modes start to affect antenna characteristics such as resonance frequency. This work presents an analysis of the structure that takes into account all higher modes of the antenna. To validate the theoretical calculations, HFSS simulations are... 

We propose a circularly polarized antenna with a wide axial ratio (AR) beamwidth that consists of a normally magnetized ferrite disk mounted on a ground plane. The device uses the resonant modes of the disk, which rotate only in the clockwise or counter-clockwise sense in the frequency range where the effective permeability of ferrite is negative. A semianalytical model is derived for the antenna fed by a single, conventional current probe and is validated numerically by finite element method. For a yttrium iron garnet disk with the radius and height of 5 and 1 mm, respectively, the results show a 3 dB AR beamwidth of 90° with an operation frequency, which can be tuned in the 4-4.5 GHz range... 

This paper proposes, for the first time, a tunable left handed transmission line consisting of a strip line sandwiched between a ferrite superstrate and a dielectric substrate containing a metallic wire array. The left-handed behavior is realized by combining the negative permittivity of the wire array with the negative permeability of the longitudinally magnetized ferrite substrate despite them being spatially separated. Theoretical and numerical results demonstrate the tunability of the left-handed frequency band by changing the DC bias magnetic field applied to the ferrite. Compared to other tunable lefthanded structures, the fabrication requirements on this structure are not critical,... 

This article proposes a tunable composite right-/left-handed transmission line consisting of a transversely magnetized ferrite substrate periodically loaded by microstrip inductors. The gapless transition between the left- and right-handed bands (balanced response) is the main characteristic of this structure. This composite right-/left-handed transmission line is proposed in both reciprocal and nonreciprocal versions. Based on periodic structure analysis, the dispersion relation is estimated theoretically and validated numerically by the finite-element method in the reciprocal case. Theoretical and numerical results demonstrate the tunability of the proposed structures by changing the DC... 

We propose, for the first time, a tunable left-handed (LH) waveguide consisting of an array of complementary split-ring resonators built on the broad wall of a rectangular waveguide filled with ferrite material. The left-handed behavior is caused by the negative permittivity of the complementary split-ring resonators together with the negative permeability of the transversely magnetized ferrite. The electromagnetic behavior of this structure is studied by means of an equivalent circuit model. From this model, the dispersion relation of the guide is derived and validated numerically by the finite element method. It is shown that this structure has a left-handed frequency band that can be... 

The insect circulatory system contains an open hemocoel, in which the mechanism of hemolymph flow control is ambiguous. As a continuous fluidic structure, this cavity should exhibit pressure changes that propagate quickly. Narrow-waisted insects create sustained pressure differences across segments, but their constricted waist provides an evident mechanism for compartmentalization. Insects with no obvious constrictions between segments may be capable of functionally compartmentalizing the body, which could explain complex hemolymph flows. Here, we test the hypothesis of functional compartmentalization by measuring pressures in a beetle and recording abdominal movements. We found that the... 

In [1], [2] it is shown that the minimum broadcast rate of a linear index code over a finite field Fq is equal to an algebraic invariant of the underlying digraph, called minrankq. In [3], it is proved that for F2 and any positive integer k, minrankq(G) ≤ k if and only if there exists a homomorphism from the complement of the graph G to the complement of a particular undirected graph family called 'graph family {Gk}'. As observed in [2], by combining these two results one can relate the linear index coding problem of undirected graphs to the graph homomorphism problem. In [4], a direct connection between linear index coding problem and graph homomorphism problem is introduced. In contrast to... 

I present an in-depth review of the trends and the directions taken by researchers worldwide in optical code-division multiple-access (OCDMA) systems. I highlight those trends and features that I believe are essential to the successful introduction of various OCDMA techniques in communication systems and data networks in the near future. In particular I begin by giving a comprehensive review of the construction of optical orthogonal codes (OOCs). Specifically I discuss the recently developed algorithms that are based on matrix algebra, which simplify and enhance the efficiencies of algorithms in OOC generation. In communication systems studies I first focus on and discuss various OCDMA... 

In this paper, we analyze the worst-case delay performance of a network of fair queuing servers in case of multiple-paths between source-destination pairs. In order to develop worst-case delay analysis for the multiple-path scenario, two challenging events should be addressed: merging different sub-streams of a session as well as distributing a traffic stream among different paths (traffic partitioning). Specifically, we propose to merge incoming sub-streams of a session to a node according to a limited rate Fair Queuing (FQ) scheme. Although the merged stream is treated as a unity, this approach results in a guaranteed level of service to each sub-stream. In addition, an algorithm is... 

This paper presents an investigation of the effects of tool rake angle and nose radius on the surface quality of ultraprecision diamond-turned porous silicon. The results showed that as rake angle decreases, the high-stress field induced by the tool edge increases, causing microcracks to propagate extensively near the pore walls. As a result, the ductile-machined areas shrank under a negative tool rake angle. On the other hand, brittle fracture occurred around pores released cutting pressure significantly. These trends of rake angle effects are distinctly different from those in the cutting of non-porous silicon. Finite element simulation of stress in the cutting area agreed with the... 

This paper presents an investigation of the effects of tool rake angle and nose radius on the surface quality of ultraprecision diamond-turned porous silicon. The results showed that as rake angle decreases, the high-stress field induced by the tool edge increases, causing microcracks to propagate extensively near the pore walls. As a result, the ductile-machined areas shrank under a negative tool rake angle. On the other hand, brittle fracture occurred around pores released cutting pressure significantly. These trends of rake angle effects are distinctly different from those in the cutting of non-porous silicon. Finite element simulation of stress in the cutting area agreed with the... 

The mechanical properties of Mg-4wt.% Zn alloy single crystals along the [0001] orientation were measured through micropillar compression at 23 °C and 100 °C. Basal slip was dominant in the solution treated alloy, while pyramidal slip occurred in the precipitation hardened alloy. Pyramidal dislocations pass the precipitates by forming Orowan loops, leading to homogeneous deformation and to a strong hardening. The predictions of the yield stress based on the Orowan model were in reasonable agreement with the experimental data. The presence of rod-shape precipitates perpendicular to the basal plane leads to a strong reduction in the plastic anisotropy of Mg. © 2020 Elsevier B.V  

The mechanical properties of Mg-4wt.% Zn alloy single crystals along the [0001] orientation were measured through micropillar compression at 23 °C and 100 °C. Basal slip was dominant in the solution treated alloy, while pyramidal slip occurred in the precipitation hardened alloy. Pyramidal dislocations pass the precipitates by forming Orowan loops, leading to homogeneous deformation and to a strong hardening. The predictions of the yield stress based on the Orowan model were in reasonable agreement with the experimental data. The presence of rod-shape precipitates perpendicular to the basal plane leads to a strong reduction in the plastic anisotropy of Mg. © 2020 Elsevier B.V  

This research explored the influences of shielding gases on the appearance of weld beads and the microstructures and mechanical properties of thin-wall samples using conventional gas metal arc welding as the heat source by using 5356 aluminium alloy welding wire as the raw materials and nitrogen (N2) and argon (Ar) as the shielding gases. The results showed that under the same parameters and after mono-layer single-bead welding was performed using N2 as the shielding gas, the bead height was higher, the bead width was narrower, and the penetration depth was shallower. The grain size of the thin-wall sample protected by N2 was 43.5–47.8 % smaller than that obtained under Ar protection.... 

In this paper, we describe a carbon dioxide mineralization process and its associated solid products. These solid products include amorphous silica, iron hydroxides and magnesium carbonates. These products were subjected to various characterization tests, and the results are published here. It was found that the iron hydroxides from this process can have different crystalline properties, and their formation depended very much on the pH of the reaction conditions. Different forms of magnesium carbonate were also obtained, and the type of carbonate precipitated was found to be dependent on the carbonation temperature. Hydromagnesite was obtained mainly at low temperatures, while dypingite was... 

Employing a proper pulse shaper in the conventional split Hopkinson pressure bar (SHPB) test helps to achieve dynamic equilibrium condition and to fulfill a constant strain rate condition in the test specimen. To this end, the parameters affecting the incident pulse shape, i.e., pulse shaper thickness, pulse shaper diameter, striker bar length and striker bar velocity are experimentally studied. Moreover, simulation results, validated by experimental data together with wave propagation analysis, are exploited to provide general guidelines to properly design a pulse shaper. It is recommended to use a relatively large diameter pulse shaper for testing work-hardening materials. Also, for... 

In this work the effects of backwash pressure, duration of acid and sodium hydroxide backwashing, sodium hydroxide concentration, and the duration of forward washing on performance of permeate flux recovery (PFR) were investigated. A two-level fractional factorial design (FFD) was used to design the experiments. The ability of back propagation neural network (BPNN) and radial basis function neural network (RBFNN) in predicting the performance of cleaning-in-place (CIP) of hydrophilic polyethersulfone (PES) membrane were investigated. It is found that BPNN has better ability in predicting the PFR performance than RBFNN. The best architecture of BPNN was a network consisting of 1 hidden layer... 

Distant, dusty and extremely luminous galaxies form a key component of the high redshift universe, tracing the period of intense cosmic activity that ultimately gave rise to the present-day universe. These highly luminous galaxies, first detected in the ground-based submillimeter region, are however optically very faint, which hampers identification of the optical counterpart and the measurement of a redshift. We are developing a new direct-detection submm spectrograph DESHIMA. By taking advantage of the rapidly advancing technology of superconducting microresonators, DESHIMA will revolutionize the appearance and capabilities of a submm spectrograph. There will no longer be large grating...