Sharif Digital Repository

Diffusive molecular communications (DiMC) have recently gained attention as a candidate for nano- to micro- and macro-scale communications due to its simplicity and energy efficiency. As signal propagation is solely enabled by Brownian motion mechanics, DiMC faces severe inter-symbol interference (ISI), which limits reliable and high data-rate communications. Herein, recent literature on DiMC performance enhancement strategies is surveyed; key research directions are identified. Signaling design and associated design constraints are presented. Studies on fundamental information theoretic limits of DiMC channel are reviewed. Classical and novel transceiver designs are discussed with an... 

Diffusive molecular communications (DiMC) have recently gained attention as a candidate for nano- to micro- and macro-scale communications due to its simplicity and energy efficiency. As signal propagation is solely enabled by Brownian motion mechanics, DiMC faces severe inter-symbol interference (ISI), which limits reliable and high data-rate communications. Herein, recent literature on DiMC performance enhancement strategies is surveyed; key research directions are identified. Signaling design and associated design constraints are presented. Studies on fundamental information theoretic limits of DiMC channel are reviewed. Classical and novel transceiver designs are discussed with an... 

This study investigates whether and how the pursuit of certain commercial business practices such as market orientation and market disruptiveness capability improves both the economic performance and social performance of social enterprises. Based on the empirical data collected from 164 UK social enterprises, our results show that market orientation improves social performance and economic performance simultaneously, whereas market disruptiveness capability improves only the economic performance, not the social performance, of social enterprises. However, we found a positive interaction effect of market disruptiveness capability and market orientation on social performance, while its effect... 

Coupling of side chain dynamics over long distances is an important component of allostery. Methionine side chains show the largest intrinsic flexibility among methyl-containing residues but the actual degree of conformational averaging depends on the proximity and mobility of neighboring residues. The 13C NMR chemical shifts of the methyl groups of methionine residues located at long distances in the same protein show a similar scaling with respect to the values predicted from the static X-ray structure by quantum methods. This results in a good linear correlation between calculated and observed chemical shifts. The slope is protein dependent and ranges from zero for the highly flexible... 

Coupling of side chain dynamics over long distances is an important component of allostery. Methionine side chains show the largest intrinsic flexibility among methyl-containing residues but the actual degree of conformational averaging depends on the proximity and mobility of neighboring residues. The 13C NMR chemical shifts of the methyl groups of methionine residues located at long distances in the same protein show a similar scaling with respect to the values predicted from the static X-ray structure by quantum methods. This results in a good linear correlation between calculated and observed chemical shifts. The slope is protein dependent and ranges from zero for the highly flexible... 

Stoichiometric hydroxyapatite (HA) powder was synthesized by wet method using orthophosphoric acid and calcium hydroxide, as raw materials. In this regard, the time-depending changes of the precipitated particles and effects of heating on them were investigated. The as-precipitated and heated powder samples were examined using field emission electron microscopy (FESEM), XRD and Raman spectroscopy methods. The results revealed that the morphology and size of the precipitated particles change in each stage of the process. After drying, these nanoparticles tend to form small agglomerates. © 2003 Elsevier Science B.V. All rights reserved  

The precipitation process considered here, involved the addition of orthophosphoric acid solution to a calcium hydroxide solution. Several parameters such as the effects of atmosphere controlling, pH, adding extra acid solution, the amount of stirring speed, and post-chemical treatment were studied. In order to study the thermal stability of synthesised powders, they were sintered for 2 h at 1200 °C and the as-precipitated and sintered powder samples were examined using SEM, XRD, FTIR and ICP methods. The results clearly revealed that the final precipitated powder is hydroxyapatite (HA) with good purity, stoichiometry and successful thermal stability. SEM high magnification micrographs... 

Very recently, two-dimensional (2D) iodinene, a novel layered and buckled structure has been successfully fabricated (Qian et al 2020 Adv. Mater. 32 2004835). Motivated by this latest experimental accomplishment, for the first time we conduct density functional theory, first-principles calculations to explore the structural, electronic, and optical properties of monolayer, few-layer and bulk iodinene. Unlike the majority of monoelemental 2D lattices, iodinene is predicted to be an intrinsic semiconductor. On the basis of calculations using the generalized gradient approximation of Perdew-Burke-Ernzerhof for the exchange-correlation functional and the Heyd-Scuseria-Ernzerhof (HSE06)... 

We present and analyse light curves of four transits of the Southern hemisphere extrasolar planetary system WASP-4, obtained with a telescope defocused so the radius of each point spread function was 17 arcsec (44 pixels). This approach minimizes both random and systematic errors, allowing us to achieve scatters of between 0.60 and 0.88 mmag per observation over complete transit events. The light curves are augmented by published observations and analysed using the jktebop code. The results of this process are combined with theoretical stellar model predictions to derive the physical properties of the WASP-4 system. We find that the mass and radius of the planet are M b = 1.289 +0.090 -0.090... 

We present in situ whole-field measurements of the temperature field using laser-induced fluorescence in a study of bottom-chilled uni-directional solidification of aqueous ammonium chloride. We utilize a two-color, two-dye, ratiometric approach to address the significant spatial and temporal variations of laser sheet intensity field due to refractive index variations caused by the evolving concentration and temperature fields. In our work we take advantage of two temperature sensitive fluorescent dyes with opposite temperature sensitivities in order to increase the overall sensitivity and temperature resolution of the measurements. The resulting temperature sensitivity (about 4% K-1) is... 

In this study, effect of desiccant wheel, heat exchanger and cooling coil will be evaluated on decreasing the wet bulb temperature of entering air to cooling tower and decreasing the outlet cold water temperature. For this purpose, change effect of desiccant wheel parameters will be investigated on wet bulb temperature of outlet air from heat exchanger. After that, optimum parameters and minimum wet bulb temperature will be selected. Then, outlet cold water temperature will be achieved for various cooling coil surface temperature with definition of by pass factor and also by using optimum desiccant wheel parameters and entrance air wet bulb temperature to tower related to cooling coil... 

The effect on the thermal parameters of superconducting transition-edge bolometers produced on a single crystalline SrTiO3 (STO) substrate with and without a CeO2 buffer layer was investigated. Metal-organic deposition was used to deposit the 20-nm CeO2 buffer layer, whereas RF magnetron sputtering was applied to fabricate 150-nm-thick superconducting YBa2Cu3O7-δ (YBCO) thin film. The critical transition temperature for both of the YBCO films was 90 K, and the transition width was ∼1.9 K. The bolometers fabricated from these samples were characterized with respect to the voltage phase and amplitude responses, and the results were compared with that of simulations conducted by applying a... 

Purpose: This study aimed to investigate the biomechanical impact of laminectomy on cervical intersegmental motion and load sharing using a parametric patient-specific finite element (FE) model towards providing clinicians with a viable quantitative tool for informed decision-making and improved surgical planning. Methods: Ten subject-specific nonlinear osteo-ligamentous cervical spine (C3–C7) FE models were developed using X-ray image-based algorithms. The models were used to evaluate the effect of laminectomy on lower cervical spine biomechanics for two-level (C3–C4) and three-level (C3–C5) laminectomy procedures. Results: The average cervical spine ranges of motion (ROM) for the pre-op... 

Purpose: This study aimed to investigate the biomechanical impact of laminectomy on cervical intersegmental motion and load sharing using a parametric patient-specific finite element (FE) model towards providing clinicians with a viable quantitative tool for informed decision-making and improved surgical planning. Methods: Ten subject-specific nonlinear osteo-ligamentous cervical spine (C3–C7) FE models were developed using X-ray image-based algorithms. The models were used to evaluate the effect of laminectomy on lower cervical spine biomechanics for two-level (C3–C4) and three-level (C3–C5) laminectomy procedures. Results: The average cervical spine ranges of motion (ROM) for the pre-op... 

Using reverse nonequilibrium molecular dynamics simulations the influence of intermolecular bridges on the thermal conductivity (λ) in carbon nanotube (CNT) bundles has been investigated. The chosen cross linkers (CH 2, O, CO) strengthen the transversal energy transport relative to the one in CNT bundles without bridges. The results showed that λ does not increase linearly with the linker density. The efficiency of the heat transport is determined by the number of linkers in the direction of the heat flux, the type of the linker, and their spatial ordering. The influence of a forced axial stress on the transversal λ has been also studied. The observed λ reduction with increasing axial... 

We employ reverse nonequilibrium molecular dynamics simulations to investigate the interfacial heat transfer in composites formed by an ungrafted or a grafted carbon nanotube which is surrounded by oligomeric polyamide-6,6 chains. The structural properties of the polymer matrix and the grafted chains are also studied. The influence of the grafting density, the length of the grafted chains as well as their chemical composition on the interfacial thermal conductivity (λi) are in the focus of our computational study. For the considered grafted polyethylene and polyamide chains we do not find a sizeable difference in the observed λi values. In contrast to this... 

We present high-precision photometry of two transit events of the extrasolar planetary system WASP-5, obtained with the Danish 1.54-m telescope at European Southern Obseratory La Silla. In order to minimize both random and flat-fielding errors, we defocused the telescope so its point spread function approximated an annulus of diameter 40 pixel (16 arcsec). Data reduction was undertaken using standard aperture photometry plus an algorithm for optimally combining the ensemble of comparison stars. The resulting light curves have point-to-point scatters of 0.50 mmag for the first transit and 0.59 mmag for the second. We construct detailed signal-to-noise ratio calculations for defocused... 

The fracture problem of a crack in a functionally graded strip with its properties varying in a linear form along the strip thickness under an anti-plane load is considered. The embedded anti-plane crack is located in the middle of strip half way through the thickness. The third mode stress intensity factor is derived using two different methods. In the first method, by employing Fourier integral transforms, the governing equation is converted to a singular integral equation, which is subsequently solved numerically by the collocation method based on Chebyshev polynomials. Then, the problem is solved by means of finite element method in which quadrilateral 8-node singular elements around... 

In this paper, a two dimensional functionally graded material (2D-FGM) under an anti-plane load with an internal crack is considered. The crack is oriented in an arbitrary direction. The material properties are assumed to vary exponentially in two planar directions. The problem is analyzed and solved by two different methods namely Fourier integral transforms with singular integral equation technique, and then by the finite element method. The effects of crack orientation, material non-homogeneity, and other parameters on the value of stress intensity factor (SIF) are studied. Finally, the obtained results for Mode III stress intensity factor of different methods are compared  

The elastic behavior of an edge dislocation located inside the core of a core-shell nanowire which is embedded in an infinite matrix is studied within the surface/interface elasticity theory. The corresponding boundary value problem is solved exactly by using complex potential functions. An important parameter so-called interface characteristic parameter which has the dimension of length and is a combination of the interface moduli enters the formulations. The stress field of the dislocation, image force acting on the dislocation, and the dislocation strain energy is calculated by considering the interface effect. The introduced characteristic parameter allows the examination of the...