Sharif Digital Repository

Considerable attention has been devoted to demonstrate reliability enhancement of power systems with power wheeling transactions. The impacts of power wheeling on power systems depends on various factors such as direction, amount of power/energy wheeled, system topology and sink or source nodes of power system. The effects on Iran Composite Power System (ICPS) reliability of wheeling energy from Azerbaijan to Turkmenistan are presented in this paper. This transaction is done through the transmission facilities on north part of ICPS. The sensitivity of ICPS to the direction and amount of power wheeling is attended. Finally, the optimum value for power wheeling is determined and the associated... 

To achieve economic stability, distribution Company as an economic institution should be managed by various processes. In this way, knowledge of different processes is the first step. Furthermore, expectations, outputs, requirement data, and sub-processes should be extracted and determined. Accordingly, to assign the performance responsibility of each process, the decision making points must be introduced and, the deviation or change in set-points should be investigated into processes. Also, the performance of processes could be monitored by introducing of the sub-indictors. In this study, a practical method is presented for monitoring of reliability and power loss indices from viewpoint... 

In distribution systems, feeder reconfiguration (FR) can lead to loss reduction, reliability improvement and some other economic savings. These advantages can be intensified by proper control and switching of Capacitor Banks (CBs). In this paper, using Ant Colony Optimization (ACO) technique, a novel method is proposed for simultaneous dynamic scheduling of FR and CB switching in the presence of DG units having uncertain and variant generations over time. This method is applicable to both smart and classic distribution systems. While for the latter, state estimation method should be used to estimate the loads at different buses by employing a limited number of measurements. The objective of... 

This paper investigates the outage probability and the throughput of relay networks with joint information and energy transfer where the relay harvests energy from transmitted radio-frequency (RF) signal of the source. Considering different power consumption models, we derive the outage probability of the systems for both adaptive and non-adaptive power allocations at the relay. With a total energy consumption constraint at the source, we provide closed-form expressions for the optimal time sharing and power allocation between the source energy and information transfer signals. The analytical and simulation results demonstrate the efficiency of joint energy and information transfer systems... 

Due to the important role that distribution systems play in quality of power delivered to the customers, there has always been a great deal of interest in investigating different methods of efficiency enhancement for these networks. Two of these methods are Feeder Reconfiguration (FR) and Capacitor Allocation (CA); both have been widely employed to reduce losses and improve several other operational characteristics in electrical power distribution systems. As in FR process the topology of the network changes, it is necessary to change some previous settings; for instance: the capacity of capacitor banks in service in each bus, after each reconfiguration process. This is due to the fact that... 

We study the tradeoff between the sum rate and the error probability in downlink of wireless networks. Using the recent results on the achievable rates of finite-length codewords, the problem is cast as a joint optimization of the network sum rate and the per-user error probability. Moreover, we develop an efficient algorithm based on the divide-and-conquer technique to simultaneously maximize the network sum rate and minimize the maximum users’ error probability and to evaluate the effect of the codeword length on the system performance. The results show that, in delay-constrained scenarios, optimizing the per-user error probability plays a key role in achieving high throughput. IEEE  

Using multiple antennas at the transmit and receive sides of a passive radar brings both the benefits of MIMO radar and passive radar. However one of the obstacles arisen in such configuration is the receive antennas placement in proper positions so that the radar performance is improved. Here we just consider the case of positioning one receiver among multiple illuminators of opportunity. Indeed it is a start for the solution of optimizing the geometry of the multiple receivers in a passive radar  

SbCl3 supported on montmorillonite K-10 is an efficient catalyst for the ring opening of epoxides with aromatic amines under solvent-free conditions and microwave irradiation to give the corresponding b-amino alcohols in high yields with high regioselectivity  

One of the important obstacles in MIMO (Multiple Input Multiple Output) radars is the issue of designing proper transmit signals. Indeed, the capability of signal design is a significant advantage in MIMO radars, through which, the system can achieve much better performance. Many different aspects of this performance improvement have been considered yet, and the transmit signals have been designed to attain such goal, e.g., getting higher SNR or better detector's performance at the receiver. However, an important tool for evaluating the radar's performance is its ambiguity function. In this paper, we consider the problem of transmit signal design, in order to optimize the ambiguity function... 

Two gains play key roles in recently developed MIMO wireless communication systems: "spatial diversity" gain and "spatial multiplexing" gain. The diversity gain refers to the capability to decrease the error rate of the MIMO channel, while the multiplexing gain implicitly refers to the amount of increase in the capacity of the MIMO channel. It has been shown that there is a fundamental tradeoff between these two types of gains, meaning interplay between increasing reliability (via an increase in the diversity gain) and increasing data rate (via an increase in the multiplexing gain). On the other hand, recently, MIMO radars have attracted much attention for their superior ability to enhance... 

It is a well known fact that using multiple antennas at transmit and receive sides improves the detection performance. However, in such multiple-input multiple-output (MIMO) configuration, proper positioning of transmitters and receivers is a big challenge that can have significant influence on the performance of the overall system. In addition, determining the power of each transmitter under a total power constraint is a problem that should be solved in order to enhance the performance and coverage of such a system. In this paper, we design the Neyman-Pearson detector under the Rayleigh scatter model and use it to introduce a criterion for the antenna placement at both transmit and receive... 

There has been much interest, recently, towards exploiting the Multiple-Input Multiple-Output (MIMO) technique in radar. It is shown that using multiple antennas at transmit and receive sides can improve the performance of the system. However, in order to analyze the system's performance, its ambiguity function, i.e. the ambiguity function of a MIMO radar, is needed to be defined. In this paper, beginning from the information theoretic definitions, we derive such function, specifically for a MIMO radar with widely separated antennas  

By combining the two ideas of MIMO (Multiple Input Multiple Output) and PCL (Passive Coherent Location) in radar, one can achieve the advantages of both recently developed techniques simultaneously. While using multiple antennas at the receive side provides a spatial diversity of the object to be detected, using multiple illuminators of opportunity, most importantly, makes the radar covert to the interceptors. One obstacle in such MIMO configuration is choosing the positions of the receive antennas. In this paper, after analyzing the Neyman-Pearson detector for the DVB-T based PCL, we introduce the probability of missed detection as a criterion to place the receive antenna. Here, we only... 

One of the most important obstacles in passive radar applications is removing the direct signal from the target channel. Otherwise, week echoes from the targets in the target channel would be ignored due to the limited dynamic range of the system. One of the most effective techniques in this field is using adaptive filters. In this paper various adaptive filters are introduced and their performances are shown and compared  

It has been shown that using multiple antennas in a radar system improves the performance considerably, since multiple target echoes are received from different aspect angles of the target. In this way, the target detection is improved. However, when using multiple antennas, some problems, such as designing the transmit signals, synchronization, etc. emerge that should be solved. One of such problems is the receiver placement. Receiver placement deals with choosing a proper position for the receive antenna in order to optimize the whole system's performance. In this paper, a receiver placement procedure based on improving the radar ambiguity function is proposed for the case of a multisite... 

By employing the MIMO (multiple-input-multiple-output) technology in radar, some new problems emerged, that, in order to benefit the MIMO gains in radar, it was necessary to solve them suitably. One of such obstacles is determining the positions of receive antennas in a MIMO radar system with widely separated antennas (WS MIMO radar), since it is shown that the antennas' positions affect the whole system's performance considerably. In this study, a proper receivers' positioning procedure is proposed. To do this end, four criteria are developed based on the proposed MIMO detector and the MIMO ambiguity function. The simulations verify that the proposed positioning procedure improves the... 

Phenols and alcohols are silylated with hexamethyldisilazane (HMDS) under microwave irradiation in solvent-free condition in good to excellent yields  

Modified couple stress theory is a size-dependent theorem capturing the micro/nanoscale effects influencing the mechanical behaviors of the micro- and nanostructures. In this paper, it is applied to investigate the nonlinear vibration of carbon nanotubes under step DC voltage. The vibration, natural frequencies and dynamic pull-in characteristics of the carbon nanotubes are studied in detail. Moreover, the effects of various boundary conditions and geometries are scrutinized on the dynamic characteristics. The results reveal that application of this theory leads to the higher values of the natural frequencies and dynamic pull-in voltages  

We study a classical problem in communication and wireless networks called Finding White Space Regions. In this problem, we are given a set of antennas (points) some of which are noisy (black) and the rest are working fine (white). The goal is to find a set of convex hulls with maximum total area that cover all white points and exclude all black points. In other words, these convex hulls make it safe for white antennas to communicate with each other without any interference with black antennas. We study the problem on three different settings (based on overlapping between different convex hulls) and find hardness results and good approximation algorithms