Loading...
Search for: hamidi--nima
0.124 seconds

    Hydrogen storage in single- and multi-walled carbon nanotubes and nanotube bundles

    , Article Australian Journal of Basic and Applied Sciences ; Volume 5, Issue 7 , 2011 , Pages 483-490 ; 19918178 (ISSN) Hamidi, S ; Golnabi, H ; Sharif University of Technology
    2011
    Abstract
    This article describes the hydrogen storage capacity in different carbon nanotubes. The hydrogen storage capacities in the armchair, zigzag, and chiral nanotubes are investigated. The hydrogen storing capacities as a function of the carbon nanotube (CNT) diameter are investigated for the single-walled (SWNT), multi-walled (MWNT), and CNT bundles and results are compared. Hydrogen storage capacity in SWNTs is increased by increasing the nanotube diameter. For diameter d=0.3887 nm of (5,0) CNT the hydrogen capacity is 0.99%, while for the (17,17) SWNT with a diameter d=2.289 nm the capacity is increased to 5.06%. In comparison of different MWNTs for a common external diameter d=1.6064 nm the... 

    The effect of filler type and content on rutting resistance of asphaltic materials

    , Article International Journal of Pavement Research and Technology ; Volume 12, Issue 3 , 2019 , Pages 249-258 ; 19966814 (ISSN) Hamidi, A ; Motamed, A ; Sharif University of Technology
    Springer  2019
    Abstract
    This research evaluates the effect of filler type and content on rutting resistance of asphaltic materials by using laboratory experiments. To examine the effect of filler type, two traditional fillers (Silica sandstone powder and Portland cement) and a new recycled lime powder (Eggshell) were considered. To investigate the effect of filler content, three different filler contents were used. Marshall Stability test was performed on full mixes in order to determine the optimum binder content of the mixtures. Then, the static creep test was performed on Fine Aggregate Matrix (FAM) samples. The permanent strain after 10 minutes of recovery (PS-660) was considered as the indicator of potential... 

    An Investigation on the Effect of Filler Type and Content on the Performance of Asphaltic Materials

    , M.Sc. Thesis Sharif University of Technology Hamidi, Arman (Author) ; Motamed, Arash (Supervisor)
    Abstract
    The objective of this research is evaluating the effect of filler type and content on the characteristics of asphaltic materials. The properties of the asphalt mixture are greatly influenced by its components. As asphalt mixtures are composed of two prominent components, aggregates and binder, the change in type and contents of these materials may lead to altering the performance of asphalt mixtures. Aggregates in the asphalt mixtures are categorized into three groups based on their particle sizes: coarse aggregate, fine aggregate and mineral filler. The effect of filler on the characteristics of asphalt mixtures can be examined by changing the type and content of filler and holding the... 

    Design and Construction of an Economic System Based on the Internet of Things (IoT) for Monitoring the Performance of Light Vessels

    , M.Sc. Thesis Sharif University of Technology Hamidi, Parsa (Author) ; Khorasanchi, Mahdi (Supervisor)
    Abstract
    Having a large source and volume of data from various machinery and electronic devices, as well as the aggregation and diverse uses of this data for higher productivity, greater safety, increased reliability, and ultimately higher profits, is a necessity and demand in every industry. This is especially important in the maritime and shipping transportation sector. The solution to predicting and preventing wear, failure, and ultimately the breakdown of vessels is to have data that is continuously and automatically collected from the ship, with the capability for transmission and analysis. The goal of this project is to develop a cost-effective system for monitoring lightweight vessels, which,... 

    Design and implementation of a new body weight support (BWS) system

    , Article 5th RSI International Conference on Robotics and Mechatronics, IcRoM 2017, 25 October 2017 through 27 October 2017 ; 2018 , Pages 69-75 ; 9781538657034 (ISBN) Hamidi Rad, M ; Behzadipour, S ; Sharif University of Technology
    Institute of Electrical and Electronics Engineers Inc  2018
    Abstract
    Gait training is a critical rehabilitation procedure for patients suffering from walking problems. It, however, puts the therapist in high orthopedic risk since he should prevent the patient from possible falling. Body weight support system is a new technology helping such patients and the involved therapist by unloading a percent of the patient's weight. A new over-ground body weight support is introduced in this article. The system is composed of two main modules namely unloading and traction. The unloading module is capable of suspending an individual's weight up to 1000N dynamically. The whole system is attached to an overhead rail, moving over the head of the patient by the traction... 

    An analytical model for evaluation of wireless mesh networks

    , Article 2008 International Symposium on Telecommunications, IST 2008, Tehran, 27 August 2008 through 28 August 2008 ; October , 2008 , Pages 295-300 ; 9781424427512 (ISBN) Hamidi Sepehr, F ; Ashtiani, F ; Sharif University of Technology
    2008
    Abstract
    Wireless mesh networks (WMNs) are well-promising future networks especially for ubiquitous connection to Internet. In this paper, we propose an analytical model in order to evaluate the maximum stable throughput of a WMN based on a simplified version of IEEE 802.11s MAC protocol. Our modeling approach is based on a multi-class open queueing network. In this respect, we map some of the important features of IEEE 802.11s MAC protocol, esp., its contention-based and contention-free periods onto different parameters of the proposed queueing network. By solving the related traffic equations and applying the stability condition, we determine the maximum stable throughput, i.e., the maximum packet... 

    Critical state concepts for a cemented gravely sand

    , Article Electronic Journal of Geotechnical Engineering ; Volume 10 E , 2005 ; 10893032 (ISSN) Hamidi, A ; Haeri, S. M ; Sharif University of Technology
    2005
    Abstract
    The shear behavior of a cemented gravely sand that can be considered as the representative of Tehran alluvium has been studied using triaxial equipment. Artificially cemented samples were prepared using gypsum plaster as the cementing agent. The plaster was mixed with the base soil at the weight percentages between 1.5 and 6. The critical state concepts were used to illustrate the mechanical behavior of tested soil. © 2005 ejge  

    Optimal Control of Spacecraft on the Earth-Moon Lagrange Point Orbits considering Sun and other Planets and Elliptic Orbit Perturbations

    , M.Sc. Thesis Sharif University of Technology Ghorbani, Mehrdad (Author) ; Assadian, Nima (Supervisor)
    Abstract
    In this thesis, optimal station keeping of spacecraft on the closed-orbits near the Earth-Moon Lagrange points has been investigated. Lagrange points L1 and L2 are unstable equilibrium points of the circular restricted three-body problem (CRTBP), and periodic orbits near them are the destination of modern missions. However, perturbations resulting from the gravitational forces of the Sun and the planets and the eccentricity of the orbit of the Moon around the Earth make the Lagrange point unstable, even L4 and L5, which are stable in CRTBP. The most suitable choice for spacecraft mission near the collinear Lagrange points is the Halo and other closed-orbits around them, which need... 

    Orbit Design and Optimization of Satellite Constellation for Regional Coverage

    , M.Sc. Thesis Sharif University of Technology Borhani, Amir (Author) ; Assadian, Nima (Supervisor)
    Abstract
    In this thesis, the satellite constellation orbit design for regional coverage is investigated. The orbits of satellites in a constellation for Earth observation missions play a crucial role in performance and characteristics of the mission; for example the image resolution, the area of coverage, and the coverage interval. In this thesis the problem is to find the optimal initial orbital elements for meeting the earth observation mission objectives for one or several sites. The cost functions are the total coverage time, the maximum gap time, time average gap, altitude, and number of satellites. The problem is solved in a multi-objective manner for different combination of two of the above... 

    Autonomous Orbit Estimation for Regional Navigation Satellites

    , M.Sc. Thesis Sharif University of Technology Memaran, Mohsen (Author) ; Asadian, Nima (Supervisor)
    Abstract
    In this thesis, autonomous orbit estimation of regional navigation satellites has been investigated. Estimation of satellite orbit is an integral part of satellite navigation, which may be executed via assistance of ground station. As the satellite is exposed to the ground station view, range, direction and rate of range is measured by mean of ranging instrumentation relative to ground reference, hence the precise position is calculated. In this thesis a set of satellites are investigated in a unique structure called constellation with the purpose of navigation. The occurrence which is likely to happen in this condition, is the failure of ground station under certain circumstances or losing... 

    Fabrication and Characterization of a UF Ceramic Membrane based on TiO_2 Nanoparticles

    , M.Sc. Thesis Sharif University of Technology Mirkazemi, Amin (Author) ; Taghavinia, Nima (Supervisor)
    Abstract
    UF membranes are widely used in various industries now, a major type of these membranes are ceramic membranes which are resistant to high temperatures and corrosive fluids. In this thesis we developed an anisotropic UF ceramic membrane based on 20nm TiO2 nanoparticles on a prous sustrate. We had two major challenges, the first one was to find a suitable prous substrate and the second one was to find an appropriate coating method. Our main task was to optimise the process conditions to achive a crackless and uniform membrane layer with minimal ups and downs. Lots of coating methods and TiO2 inks have been tried, finally we used a coating method which we called it “Soft Blade Coating”, with... 

    Continuous-thrust Trajectory Optimization in the Binary Asteroids System

    , M.Sc. Thesis Sharif University of Technology Ashrafi, Mehnraz (Author) ; Asadian, Nima (Supervisor)
    Abstract
    In this thesis, the optimal trajectories of a spacecraft in the binary asteroids system is studied. The objective functions of optimal trajectories in these system are the maximum coverage of the asteroids surface and minimum time and fuel consumption. For this purpose, the dynamic of binary system is modeled. The binary system of 1999 KW4 is selected as a case study. The ellipsoid-sphere model is a good approximation for the case of this study. In this model, the asteroids orbit in a circular orbit around each other in a spin-spin-orbit resonance configuration, in which the asteroids’ rotational velocity is equal to orbital mean motion. Then, the equations of motion of the spacecraft as the... 

    Fault-tolerant Attitude Control of Sattelite Using Neural Networks

    , M.Sc. Thesis Sharif University of Technology Sepehr, Firoozeh (Author) ; Asadian, Nima (Supervisor)
    Abstract
    This research aims to introduce a new integrated fault tolerant attitude control system of satellites based on the neural networks. First, a linear controller and an optimal controller are designed assuming that no fault occurs in the reaction wheels of the satellite. It is obvious that these controllers are not able to respond properly when a fault occurs. Therefore, artificial neural networks are employed in the fault tolerant controller design. Neural networks are well-known for their adaptiveness and the ability to learn the dynamics of a system. Therefore, they can be used to predict the faulty conditions. In this research two approaches are examined to deal with the faulty conditions.... 

    Fabrication and Characterization of Inverted Perovskite Solar Cells Using Nickel Oxide as Hole Transporting Layer

    , Ph.D. Dissertation Sharif University of Technology Saki, Zahra (Author) ; Taghavinia, Nima (Supervisor)
    Abstract
    In this research, we study and optimize the inverted perovskite solar cells (PSCs) using nano layers of NiOx and Li:NiOx as hole transporting layers (HTLs) and nano layers of PC70BM and C60 as electron transporting layers (ETLs). We fabricated inverted PSCs with three different HTLs, namely MoOx, PEDOT:PSS and NiOx, using vapor assisted solution processed (VASP) method for making MAPbI3 perovskite which yielded a power conversion efficiency (PCE) of 1%, 1.93% and 3.65%, respectively. Solution-processed deposition method, high transparency (˃90%) and high band gap (3.9 eV) are the most advantages to use NiOx as HTL in current research. Using lithium as dopant to the NiOx increases the... 

    Dynamics of Tethered Satellite Formation Around Binary Asteroids

    , M.Sc. Thesis Sharif University of Technology Bakhshipour, Mehran (Author) ; Assadian, Nima (Supervisor)
    Abstract
    Studying of binary asteroids because of achieving data of existence sources in the world persuades to investigate about tethered satellite formation around binary asteroids in future missions. About 20 percent of asteroids around the sun are binary asteroids. It is going to analyse dynamics of tethered satellite around Didymos binary asteroid. Light mass of the asteroid is good reason to consider gravitational harmonic perturbation, and leads to attention about solar radiation pressure depends on distance in modelling of the dynamical system. It will be zonal harmonics up to second order and sectoral. Satellites are such a particle as an assumption; that is why attitude motion of satellites... 

    Fractional Order Modeling and Control of Flexible Satellite

    , M.Sc. Thesis Sharif University of Technology Hosseini, Masoud (Author) ; Assadian, Nima (Supervisor)
    Abstract
    In recent decades the structure of space systems has gained more complexity due to the development of space technology. Usage of larger structure in spacecraft could cause undesirable structural vibration. mNeglecting this phenomena would affect the performance of satellite subsystems specially the accuracy of satellite control subsystem. By implementing fractional order calculus in modeling of flexible satellite, the damping effect could be modeled better than classical damping model. Also using fractional order integrator and differentiator operator will increase the performance of control subsystem. In this research, the fractional order calculus has been used in modeling and control of... 

    Spacecraft Rendezvous and Docking Using Adaptive Neuro-Fuzzy Inference System

    , M.Sc. Thesis Sharif University of Technology Tallebi, Morteza (Author) ; Asadian, Nima (Supervisor)
    Abstract
    In this research an ANFIS controller will be developed to rendezvous and dock with a non-cooperative spacecraft; the controller must make the spacecraft reach the velocity and nearby position of the target spacecraft. Due to uncertainty in modeling and changes in the moment inertia tensor, the controller must be able to adapt with these changes and uncertainty, these changes may happen because of robotic arm or solar panel movings. Robustness of the controller will be evaluated by applying orbital disturbances and modeling errors through monte-carlo simulations. To model the spacecraft the specifications of a known spacecraft will be used but some specifications may be studied parametricaly.... 

    Coupled Rotational and Translational Modelling of Two Satellite Tethered Formation and their Robust Attitude Control

    , M.Sc. Thesis Sharif University of Technology Darabi, Atefe (Author) ; Assadian, Nima (Supervisor)
    Abstract
    The 6DOF modelling and robust attitude control of two tethered satellites using tether tension moments is studied in this thesis. In this regard, the coupled rotational and translational dynamics of two satellites connected by a tether in the presence of Earth’s gravitational perturbation, aerodynamic drag, solar radiation pressure and third body effects (Sun and Moon) and also uncertainties in some of physical parameters of system and sensor’s outputs is modelled. Moreover, the tether attachment point to the satellites is different from their center of mass and its effect on dynamics of the system is taken into consideration. Then, the attitude of both satellites are controlled using robust... 

    Fault-Tolerant Attitude Control of Satellite with Thrusters Using μ-synthesis

    , M.Sc. Thesis Sharif University of Technology Taheri, Abdolreza (Author) ; Assadian, Nima (Supervisor)
    Abstract
    In this project, a fault-tolerant attitude control system is developed for thruster-driven satellites. The proposed method has the advantage over current state-of-the-art approaches in that it does not require a fault detection and isolation system. Generalized moments are generated by a robust controller that is designed using mixed sensitivity H_∞ and μ-synthesis by DK-iteration. Moreover, a pulse-width modulation technique with quadratic programming optimization is tuned to map the controller outputs to thruster on-off commands as efficiently as possible. The controller is designed to tolerate up to ±30% perturbations in inertia properties and thrust degradations up to 90% of the nominal... 

    Attitude and Deformation Estimation of Flexible Satellite Using Magnetometer and Sun Sensor

    , M.Sc. Thesis Sharif University of Technology Ghani, Marzieh (Author) ; Asadian, Nima (Supervisor)
    Abstract
    The estimation of attitude and deformation of a flexible satellite using magnetometer and sun sensor data are studied in this thesis. To this end, the dynamical differential equations of the flexible satellite have been derived using Lagrange’s equation. These equations of motion are then utilized for the purpose of simulation and verification. After introducing the measurements equations, the observability of the satellite with flexible panels has been evaluated. Afterward, the attitude of the satellite body and deformation of the flexible panels have been estimated by EKF (Extended Kalman Filter) as well as UKF (Unscented Kalman Filter). The results show that the estimations using UKF are...