Sharif Digital Repository

This paper describes a new compensating system for the flicker and harmonics generated by a highly-varying load, e.g. a welding machine, connected between two phases of a three-phase system. The proposed system is an active filter with two-phase structure employed in a three-phase system. The system also employs simple and effective control strategies for dc-bus regulation and current control. The proposed system is a package with less switches compared to the conventional three-phase systems. It results in no increase in switch ratings, thus giving a more economic compensator. © 2006 IEEE  

In this paper, a new simple and complete technique of modeling and analysis of a matrix converter is presented based on the singular value decomposition (SVD) of modulation matrix. The proposed modeling method yields a new limitation between the matrix converter gain and its input power factor, which is more relaxed as compared to the limits reported so far in the literature. The SVD of the modulation matrix leads to a unified modulation technique which achieves the full capability of a matrix converter. It is shown that this approach is general and all other modulation methods established for a matrix converter are specific cases of this technique. The proposed modulation method can be used... 

In this paper, the reactive power control of a variable-speed permanent-magnet synchronous wind generator with a matrix converter at the grid side is improved. A generalized modulation technique based on singular value decomposition of the modulation matrix is used to model different modulation techniques and investigate their corresponding input reactive power capability. Based on this modulation technique, a new control method is proposed for the matrix converter which uses active and reactive parts of the generator current to increase the control capability of the grid-side reactive current compared to conventional modulation methods. A new control structure is also proposed which can... 

A matrix converter is a voltage/current source AC/AC frequency converter. In grid-connected operation of a variable-speed permanent magnet synchronous wind power generator, the matrix converter is normally controlled as a voltage source converter. In this control method, the generator-side voltage is synthesized from the grid-side voltage source. However, in the stand-alone mode of operation, the grid-side stiff voltage source is not available, and the input filter of the matrix converter is unstable. In this article, a new control method is presented that controls a permanent magnet synchronous wind generator in a stand-alone mode with a matrix converter as a current source converter. The... 

In this paper an analytical approach is proposed to formulate the proper set of phase currents reference to ride the permanent magnet synchronous generator (PMSG)-based wind turbine (WT) through faults properly, regardless of fault type. Hence, the WT is forced to inject required reactive current by grid codes together with active power injection, to help support grid frequency during faults and reduce the energy storage system (ESS) power rating. Moreover, it prevents pulsating active power injection to the grid. During grid faults, the DC-link voltage is controlled by the ESS instead of the grid-side converter (GSC) and the GSC controller applies calculated reference currents. The ESS... 

A novel fault ride-through strategy for wind turbines, based on permanent magnet synchronous generator, has been proposed. The proposed strategy analytically formulates the reference current signals, disregarding grid fault type and utilizes the whole system capacity to inject the reactive current required by grid codes and deliver maximum possible active power to support grid frequency and avoid generation loss. All this has been reached by taking the grid-side converter’s phase current limit into account. The strategy is compatible with different countries’ grid codes and prevents pulsating active power injection, in an unbalanced grid condition. Model predictive current controller is... 

The title compound, C32H26N2S2, is a new spiro thio-oxindole derivative which was synthesized with the aim that it might be effective in treating a number of diseases. In spite of the existence of the Csp 3 atom, the thio-oxindole group is almost planar. There are a number of intra-molecular C - H⋯S hydrogen bonds. © International Union of Crystallography 2007  

The catalytic activity of a mixture of ZnCl2: AlCl3 supported on silica gel was evaluated for the alkylation of phenols with benzyl alcohol, tret-butyl alcohol and styrene under microwave irradiation and solvent-free conditions. The catalyst preparation method, its characterization and reusability, were reported. The effect of the phenol to benzyl alcohol ratio and the time of reaction on the phenol conversion and distribution of products was investigated. A conversion percentage up to 97% was achieved when hydroquinone was used. A selective ortho- directed alkylation for phenol, α-naphthol and β-naphthol was observed. © Sharif University of Technology, December 2009  

Herein we report a new organocatalyst for the asymmetric Michael addition of nitroalkanes to α,β-unsaturated aldehydes. This catalyst incorporates a basic imidazole group in addition to the secondary amine responsible for activation of the α,β-unsaturated carbonyl compounds via iminium ion formation. The new organocatalyst is capable of catalyzing the enantioselective carbon-carbon bond formation with a high degree of enantiocontrol providing products in enantiomeric excesses of up to 92% and yields of up to to 91 %. These results constitute the best results so far reported for organocatalyzed Michael additions of nitroalkanes to α,β-unsaturated aldehydes, and provide proof of principle that... 

An efficient and one-pot synthesis of thiopyrano[2,3-b]indole derivatives via Hetero Diels-Alder reaction of α,β-Unsaturated thio-oxindoles with electron poor acetylenes and Cyclic Dienophiles is described. In the proposed method the reaction is performed under neutral and one-pot reaction conditions, and also the substances can be mixed without any activation or modification and without using any catalysts  

Four 5-, 10-, 20- and 30-story moment frames, representing low-, mid-, and two high-rise structures, were subjected to a great number of idealized directivity pulses. The amplitudes and periods of pulses vary from 0.02 g to 1.0 g and 0.5 to 12 sec, respectively. Over 1400 nonlinear dynamic analyses of low- to high-rise moment frames were performed which were feasible through using modified fish-bone model. The distribution of interstory drift along the height was studied and two applied contours were proposed: (i) the maximum interstory drift contour, and (ii) the critical story contour. These contours were demonstrated versus the ratio of natural period of the structure to the pulse period... 

In this article singular points of a parallel manipulator are obtained based on a novel geometrical method. Here we introduce the constrained plain method (CPM) and some of its application in parallel mechanism. Given the definition of constraint plane (CP) and infinite constraint plane (ICP) the dependency conditions of constraints is achieved with the use of a new theorem based on the Ceva geometrical theorem. The direction of angular velocity of a body is achieved by having three ICPs with the use of another theorem. Finally, with the use of the above two novel theorems singularities of the 3UPF_PU mechanism are obtained. It should be emphasized that this method is completely geometrical,... 

An analytical model is proposed to study the effect of particle size on melting enthalpy and entropy of metallic nanoparticles (NPs). The Mott's and Regel's equations for melting entropy in the combination of core average coordination number (CAC) and surface average coordination number (SAC) of freestanding NPs are considered. Clusters of icosahedral (IC), body centered cubic (BCC), and body centered tetragonal (BCT) structure without any vacancies and defects are modeled. Using the variable coordination number made this model to be in good agreement with experimental and molecular dynamic (MD) results of different crystal structures. The model predicts melting entropy and enthalpy of... 

Grinding is widely used for manufacturing of components that require fine surface finish and good dimensional accuracy. In this study a thermo-mechanical finite element analysis is conducted to find out how grinding parameters can affect temperature and residual stress distribution in the workpiece. Results of parametric study presented in this work indicate, by carefully selecting the grinding parameters, minimum thermal and mechanical damage can be achieved. Higher workpiece velocities produce higher surface residual stress. By increasing depths of cut, depth of tensile residual stresses increases. Convection heat coefficient does not have any considerable effect on surface residual stress... 

Adaptive Noise Cancellation (ANC) is a well-known technique for background noise reduction in automobile and vehicular environments. The noise fields in automobile and other vehicle interior obey the diffuse noise field model closely. On the other hand, the ANC does not provide sufficient noise reduction in the diffuse noise fields. In this paper, a new multistage post-filter is designed for ANC as a solution to diffuse noise conditions. The designed post-filter is a single channel Linear Prediction (LP) based speech enhancement system. The LP is performed by an adaptive lattice filter and attempts to extract speech components by using intermediate ANC signals. The post-filter has no... 

Shot peening is widely used to improve the fretting fatigue strength of critical surfaces. Fretting fatigue occurs in contacting parts that are subjected to fluctuating loads and sliding movements at the same time. This paper presents a sequential finite element simulation to investigate the shot peening effects on normal stress, shear stress, bulk stress and slip amplitude, which are considered to be the controlling parameters of fretting damage. The results demonstrated that among the modifications related to shot peening, compressive residual stress has a dominant effect on the fretting parameters  

One-dimensional (1D) MgO structures were successfully synthesized via carbothermic reduction of mechanically activated mixture of MgO and graphite. Mechanical activation of source materials before carbothermic reduction can substantially enhance the formation of MgO products at a temperature (1000 °C) relatively lower than that required in previous approaches (≥1200 °C). However, the morphology of MgO formed is dependent on the degree of mechanical activation and the condition of the subsequent carbothermic reduction. Two distinctive morphologies were found for MgO products synthesized using our method: single crystalline nanorods with rectangular cross-sections whose diameters range from 50... 

Attitude and vibration control of a general form of flexible satellites is addressed in this paper. Partial differential dynamic equations are derived considering new details such as multi sectioned solar panels and elastic connections between main hub and solar panels. Boundary control approach is adopted to eliminate simplification errors of discrete models, using just one actuator in the hub. Asymptotic stability of attitude dynamics is proved for a group of boundary controllers and necessary conditions for asymptotic stability of vibrations are discussed. Being independent of modeling accuracy and using easily measurable feedbacks are among advantages of the proposed class of... 

Characterization and calcination behavior of a low-grade manganese ore, as a part of Mn ferroalloys production, was studied by XRF, ex-situ XRD, in-situ XRD, and SEM-EDS techniques. Calcination experiments were carried out at and up to 900 °C (1173 K) in air and argon atmospheres. The samples were in particles and powder forms. The results indicated that both quartz and calcite phases in the ore exhibit a bimodal spatial distribution; as relatively large regions and finely distributed in the Mn- and Fe-containing phases. By Rietveld analysis of the in-situ XRD data, the reactions occurring upon heating during the calcination process were deduced. Thermal decomposition and reactive diffusion...